-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
Hello!
I try to setup a wireless card to my gentoo box, but I can't set it:
the net is with a wpa-key (type tkip). The SSID is Super S and when I
configure it so:
#iwconfig wlan0 essid "my SSID" nick "Cinzia" key wep-key
after that I read with iwconfig:
# iwconfig wlan0
wlan0 IEEE 802.11b+/g+ ESSID:"my SSID"
Mode:Managed Channel:1 Access Point: 00:00:80:F9:37:03
Bit Rate:268.501 Mb/s Tx-Power:268500993 Sensitivity:24937
Retry:on Fragment thr=256 B
Encryption key:xxxx-xxxx-xxxx-xxxx-xxxx-xxxx-xx Security
mode:restricted
Power Management:on
But if I do
#dhcpd wlan0
the card doesn't try to contact the router (no log) and in dmesg:
#dmesg
updating initial settings on iface activation
get_mask 0x00000000, set_mask 0x0006CEBC
important setting has been changed. Need to update packet templates, too
updating packet templates
updating transmit power: 15 dBm
updating antenna value: 0x4A
updating Energy Detect (ED) threshold: 0
acx111 doesn't support ED!
updating Channel Clear Assessment (CCA) value: 0x00
acx111 doesn't support CCA!
updating channel to: 1
updating: enable Tx
updating: enable Rx on channel: 1
updating regulatory domain: 0x30
updating WEP key settings
setting WEP key: 0 with total size: 13
setting WEP key 0 as default
acx_set_status(1):SCANNING
starting radio scan
get_mask 0x00000000, set_mask 0x00000000 - after update
ADDRCONF(NETDEV_UP): wlan0: link is not ready
acx_i_timer: adev->status=1 (SCANNING)
continuing scan (1 sec)
acx_i_timer: adev->status=1 (SCANNING)
continuing scan (2 sec)
acx_i_timer: adev->status=1 (SCANNING)
continuing scan (3 sec)
acx_i_timer: adev->status=1 (SCANNING)
continuing scan (4 sec)
acx_i_timer: adev->status=1 (SCANNING)
continuing scan (5 sec)
acx_i_timer: adev->status=1 (SCANNING)
continuing scan (6 sec)
acx_i_timer: adev->status=1 (SCANNING)
stopping scan
no matching station found in range yet
acx_set_status(1):SCANNING
starting radio scan
rx: unsupported 802.11 protocol
rx: unsupported 802.11 protocol
acx_i_timer: adev->status=1 (SCANNING)
continuing scan (1 sec)
acx_i_timer: adev->status=1 (SCANNING)
continuing scan (2 sec)
acx_i_timer: adev->status=1 (SCANNING)
continuing scan (3 sec)
acx_i_timer: adev->status=1 (SCANNING)
continuing scan (4 sec)
acx_i_timer: adev->status=1 (SCANNING)
continuing scan (5 sec)
acx_i_timer: adev->status=1 (SCANNING)
continuing scan (6 sec)
acx_i_timer: adev->status=1 (SCANNING)
stopping scan
no matching station found in range yet
acx_set_status(1):SCANNING
starting radio scan
rx: unsupported 802.11 protocol
acx: truncated rx header (-1656 bytes)!
rx: unsupported 802.11 protocol
acx_i_timer: adev->status=1 (SCANNING)
continuing scan (1 sec)
acx_i_timer: adev->status=1 (SCANNING)
continuing scan (2 sec)
acx_i_timer: adev->status=1 (SCANNING)
continuing scan (3 sec)
acx_i_timer: adev->status=1 (SCANNING)
continuing scan (4 sec)
It is a card problem and a setup problem? The card uses experimental acx
driver (it is a AVM Fritz! WLAN USB)
Thanks a lot,
Luigi
- --
Public key GPG(0x633F86B7) on http://keyserver.linux.it/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.2.2 (GNU/Linux)
iD8DBQFEP/x+HmkkjmM/hrcRAtxDAJ0YMZxXmjQax5BMFAV49aaCaLrvTACfVKen
D8O1UUSA0ctlJFUwiTdUmlA=
=4cQv
-----END PGP SIGNATURE-----
--
gentoo-user@gentoo.org mailing list
