Hi there,
Need some help here, tried googling with no luck ..
I run cdrecord as usual, then everything looks fine, then the LED of the drive
goes on for a couple of seconds then goes off and everything continues
perfectly till the end, the media is ejected, but it is not touched at all as
if "-dummy" was active. No apparent error mesage.
Have no idea what else to look for !
If this is not the correct list, please point me to the correct place.
TIA.
attached as much info as i could think of.
# cdrecord -dev=0,0,0 -speed=1 -v --eject -dao myimage.iso
Cdrecord 1.11a15 (i686-pc-linux-gnu) Copyright (C) 1995-2001 J\uffffrg Schilling
TOC Type: 1 = CD-ROM
scsidev: '0,0,0'
scsibus: 0 target: 0 lun: 0
Linux sg driver version: 3.5.33
Using libscg version 'bero-0.5a'
cdrecord: Warning: using inofficial version of libscg (bero-0.5a
'@(#)scsitransp.c 1.81 01/04/20 Copyright 1988,1995,2000 J. Schilling').
atapi: 1
Device type : Removable CD-ROM
Version : 2
Response Format: 2
Capabilities :
Vendor_info : 'PIONEER '
Identifikation : 'DVD-RW DVR-110 '
Revision : '1.22'
Device seems to be: Generic mmc2 DVD.
Using generic SCSI-3/mmc DVD-R(W) driver (mmc_mdvd).
Driver flags : SWABAUDIO BURNFREE
Supported modes: PACKET SAO
Drive buf size : 1024000 = 1000 KB
FIFO size : 4194304 = 4096 KB
Track 01: data 4444 MB
Total size: 5104 MB (505:40.17) = 2275513 sectors
Lout start: 5104 MB (505:42/13) = 2275513 sectors
Current Secsize: 2048
ATIP start of lead in: -150 (00:00/00)
Disk type: unknown dye (reserved id code)
Manuf. index: -1
Manufacturer: unknown (not in table)
Blocks total: 2298496 Blocks current: 2298496 Blocks remaining: 22983
Starting to write CD/DVD at speed 1 in dummy mode for single session.
Last chance to quit, starting dummy write in 0 seconds. Operation starts.
Waiting for reader process to fill input buffer ... input buffer ready.
trackno=0
BURN-Free is OFF.
Sending CUE sheet...
cdrecord: WARNING: Drive returns wrong startsec (0) using -150
Starting new track at sector: 0
Track 01: 4444 of 4444 MB written (fifo 100%).
Track 01: Total bytes read/written: 4660250624/4660250624 (2275513 sectors).
Writing time: 101.814s
Fixating...
WARNING: Some drives don't like fixation in dummy mode.
Fixating time: 0.006s
cdrecord: fifo had 73404 puts and 73404 gets.
cdrecord: fifo was 809 times empty and 639 times full, min fill was 0%.
#cdrecord -scanbus
Cdrecord 1.11a15 (i686-pc-linux-gnu) Copyright (C) 1995-2001 J\uffffrg Schilling
Linux sg driver version: 3.5.33
Using libscg version 'bero-0.5a'
cdrecord: Warning: using inofficial version of libscg (bero-0.5a
'@(#)scsitransp.c 1.81 01/04/20 Copyright 1988,1995,2000 J. Schilling').
scsibus0:
0,0,0 0) 'PIONEER ' 'DVD-RW DVR-110 ' '1.22' Removable CD-ROM
0,1,0 1) *
0,2,0 2) *
0,3,0 3) *
0,4,0 4) *
0,5,0 5) *
0,6,0 6) *
0,7,0 7) *
scsibus1:
1,0,0 100) 'PIONEER ' 'DVD-ROM DVD-117 ' '1.07' Removable CD-ROM
1,1,0 101) *
1,2,0 102) *
1,3,0 103) *
1,4,0 104) *
1,5,0 105) *
1,6,0 106) *
1,7,0 107) *
scsibus2:
2,0,0 200) 'ATA ' 'HDS722516VLSA80 ' 'V34O' Disk
2,1,0 201) *
2,2,0 202) *
2,3,0 203) *
2,4,0 204) *
2,5,0 205) *
2,6,0 206) *
2,7,0 207) *
#dmesg
Linux version 2.6.12-gentoo-r10power-izel ([EMAIL PROTECTED]) (gcc
version 3.3.5-20050130 (Gentoo 3.3.5.20050130-r1, ssp-3.3.5.20050130-1,
pie-8.7.7.1)) #1 Tue Sep 27 21:56:53 JST 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003ff40000 (usable)
BIOS-e820: 000000003ff40000 - 000000003ff50000 (ACPI data)
BIOS-e820: 000000003ff50000 - 0000000040000000 (ACPI NVS)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
127MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000ff780
On node 0 totalpages: 261952
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 225280 pages, LIFO batch:31
HighMem zone: 32576 pages, LIFO batch:15
DMI 2.3 present.
ACPI: RSDP (v000 ACPIAM ) @ 0x000f67e0
ACPI: RSDT (v001 A M I OEMRSDT 0x08000430 MSFT 0x00000097) @ 0x3ff40000
ACPI: FADT (v002 A M I OEMFACP 0x08000430 MSFT 0x00000097) @ 0x3ff40200
ACPI: MADT (v001 A M I OEMAPIC 0x08000430 MSFT 0x00000097) @ 0x3ff40300
ACPI: OEMB (v001 A M I OEMBIOS 0x08000430 MSFT 0x00000097) @ 0x3ff50040
ACPI: DSDT (v001 1ABVA 1ABVA003 0x00000003 INTL 0x02002026) @ 0x00000000
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 6:10 APIC version 16
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 3, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 40000000 (gap: 40000000:bff80000)
Built 1 zonelists
Kernel command line: root=/dev/hda3 hdc=ide-scsi hdb=ide-scsi video=vesafb-tng
ide_setup: hdc=ide-scsi
ide_setup: hdb=ide-scsi
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 2101.027 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1033476k/1047808k available (2881k kernel code, 13524k reserved, 1183k
data, 196k init, 130304k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 4120.57 BogoMIPS (lpj=2060288)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0383fbff c1c3fbff 00000000 00000000
00000000 00000000 00000000
CPU: After vendor identify, caps: 0383fbff c1c3fbff 00000000 00000000 00000000
00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: After all inits, caps: 0383fbff c1c3fbff 00000000 00000020 00000000
00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: AMD Athlon(tm) XP 3000+ stepping 00
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 pin1=2 pin2=-1
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=2
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050309
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:02:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs *10)
ACPI: PCI Interrupt Link [LNKD] (IRQs *3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
Machine check exception polling timer started.
audit: initializing netlink socket (disabled)
audit(1127827653.166:0): initialized
highmem bounce pool size: 64 pages
inotify device minor=63
Installing knfsd (copyright (C) 1996 [EMAIL PROTECTED]).
Linux agpgart interface v0.101 (c) Dave Jones
[drm] Initialized drm 1.0.0 20040925
PCI: Enabling device 0000:00:05.0 (0000 -> 0003)
[drm] Initialized sis 1.1.0 20030826 on minor 0: Silicon Integrated Systems
[SiS] 300/305 PCI/AGP VGA Display Adapter
vesafb: NVidia Corporation, NV15 Reference Board, Chip Rev A0 (OEM: NVidia)
vesafb: VBE version: 3.0
vesafb: protected mode interface info at c000:0ef9
vesafb: pmi: set display start = c00c0f32, set palette = c00c0fa8
vesafb: pmi: ports = 3b4 3b5 3ba 3c0 3c1 3c4 3c5 3c6 3c7 3c8 3c9 3cc 3ce 3cf
3d0 3d1 3d2 3d3 3d4 3d5 3da
vesafb: hardware supports DDC2 transfers
vesafb: monitor limits: vf = 75 Hz, hf = 83 kHz, clk = 140 MHz
vesafb: scrolling: redraw
Console: switching to colour frame buffer device 128x48
vesafb: framebuffer at 0xb0000000, mapped to 0xf8880000, using 1536k, total
65536k
fb0: VESA VGA frame buffer device
ACPI: Power Button (FF) [PWRF]
ACPI: Sleep Button (CM) [SLPB]
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
mice: PS/2 mouse device common for all mice
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
loop: loaded (max 8 devices)
e100: Intel(R) PRO/100 Network Driver, 3.4.8-k2-NAPI
e100: Copyright(c) 1999-2005 Intel Corporation
ACPI: PCI Interrupt 0000:01:04.0[A] -> GSI 19 (level, low) -> IRQ 19
e100: eth0: e100_probe: addr 0xafefe000, irq 19, MAC addr 00:50:8B:BC:0C:26
ACPI: PCI Interrupt 0000:01:05.0[A] -> GSI 16 (level, low) -> IRQ 16
e100: eth1: e100_probe: addr 0xafeff000, irq 16, MAC addr 00:50:8B:BC:0C:27
VIA Networking Velocity Family Gigabit Ethernet Adapter Driver Ver. 1.13
Copyright (c) 2002, 2003 VIA Networking Technologies, Inc.
Copyright (c) 2004 Red Hat Inc.
ACPI: PCI Interrupt 0000:00:0b.0[A] -> GSI 18 (level, low) -> IRQ 18
PCI: Via IRQ fixup for 0000:00:0b.0, from 10 to 2
eth2: VIA Networking Velocity Family Gigabit Ethernet Adapter
eth2: Ethernet Address: 00:11:09:86:05:2B
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:0f.1
ACPI: PCI Interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 20
PCI: Via IRQ fixup for 0000:00:0f.1, from 255 to 4
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
input: AT Translated Set 2 keyboard on isa0060/serio0
hda: ST360020A, ATA DISK drive
input: ImExPS/2 Generic Explorer Mouse on isa0060/serio1
hdb: PIONEER DVD-RW DVR-110, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: Pioneer DVD-ROM ATAPIModel DVD-117 0107, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide4...
Probing IDE interface ide5...
hda: max request size: 128KiB
hda: 117231408 sectors (60022 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100)
hda: cache flushes not supported
hda: hda1 hda2 hda3 hda4
ide-scsi is deprecated for cd burning! Use ide-cd and give dev=/dev/hdX as
device
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: PIONEER Model: DVD-RW DVR-110 Rev: 1.22
Type: CD-ROM ANSI SCSI revision: 02
scsi1 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: PIONEER Model: DVD-ROM DVD-117 Rev: 1.07
Type: CD-ROM ANSI SCSI revision: 02
libata version 1.11 loaded.
sata_via version 1.1
ACPI: PCI Interrupt 0000:00:0f.0[B] -> GSI 20 (level, low) -> IRQ 20
PCI: Via IRQ fixup for 0000:00:0f.0, from 10 to 4
sata_via(0000:00:0f.0): routed to hard irq line 4
ata1: SATA max UDMA/133 cmd 0xD800 ctl 0xD402 bmdma 0xC800 irq 20
ata2: SATA max UDMA/133 cmd 0xD000 ctl 0xCC02 bmdma 0xC808 irq 20
ata1: dev 0 cfg 49:2f00 82:74eb 83:7fea 84:4023 85:74e9 86:3c02 87:4023 88:203f
ata1: dev 0 ATA, max UDMA/100, 321672960 sectors: lba48
ata1: dev 0 configured for UDMA/100
scsi2 : sata_via
ata2: no device found (phy stat 00000000)
scsi3 : sata_via
Vendor: ATA Model: HDS722516VLSA80 Rev: V34O
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 321672960 512-byte hdwr sectors (164697 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 321672960 512-byte hdwr sectors (164697 MB)
SCSI device sda: drive cache: write back
sda: sda1 sda2
Attached scsi disk sda at scsi2, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 5
Attached scsi generic sg1 at scsi1, channel 0, id 0, lun 0, type 5
Attached scsi generic sg2 at scsi2, channel 0, id 0, lun 0, type 0
usbmon: debugs is not available
ACPI: PCI Interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 21
PCI: Via IRQ fixup for 0000:00:10.4, from 10 to 5
ehci_hcd 0000:00:10.4: VIA Technologies, Inc. USB 2.0
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:10.4: irq 21, io mem 0xfebffc00
ehci_hcd 0000:00:10.4: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
USB Universal Host Controller Interface driver v2.2
ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 21
PCI: Via IRQ fixup for 0000:00:10.0, from 11 to 5
uhci_hcd 0000:00:10.0: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.0: irq 21, io base 0x0000dc00
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 21
PCI: Via IRQ fixup for 0000:00:10.1, from 11 to 5
uhci_hcd 0000:00:10.1: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (#2)
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.1: irq 21, io base 0x0000e000
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.2: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (#3)
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.2: irq 21, io base 0x0000e400
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.3: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (#4)
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:10.3: irq 21, io base 0x0000ec00
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.01:USB HID core driver
Advanced Linux Sound Architecture Driver Version 1.0.9rc2 (Thu Mar 24
10:33:39 2005 UTC).
ALSA device list:
No soundcards found.
NET: Registered protocol family 2
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP established hash table entries: 262144 (order: 9, 2097152 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
ip_conntrack version 2.1 (8186 buckets, 65488 max) - 212 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
ipt_recent v0.3.1: Stephen Frost <[EMAIL PROTECTED]>.
http://snowman.net/projects/ipt_recent/
arp_tables: (C) 2002 David S. Miller
NET: Registered protocol family 1
NET: Registered protocol family 17
ACPI wakeup devices:
PCI0 MC97 USB1 USB2 USB3 USB4 EHCI ILAN SLPB
ACPI: (supports S0 S1 S3 S4 S5)
ReiserFS: hda3: found reiserfs format "3.6" with standard journal
ReiserFS: hda3: using ordered data mode
ReiserFS: hda3: journal params: device hda3, size 8192, journal first block
18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda3: checking transaction log (hda3)
ReiserFS: hda3: replayed 6 transactions in 1 seconds
ReiserFS: hda3: Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Freeing unused kernel memory: 196k freed
Adding 2449904k swap on /dev/hda2. Priority:-1 extents:1
ReiserFS: hda3: Removing [7239 633558 0x0 SD]..done
ReiserFS: hda3: There were 1 uncompleted unlinks/truncates. Completed
ReiserFS: sda1: found reiserfs format "3.6" with standard journal
ReiserFS: sda1: using ordered data mode
ReiserFS: sda1: journal params: device sda1, size 8192, journal first block
18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sda1: checking transaction log (sda1)
ReiserFS: sda1: replayed 1 transactions in 0 seconds
ReiserFS: sda1: Using r5 hash to sort names
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
nvidia: module license 'NVIDIA' taints kernel.
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 16
NVRM: loading NVIDIA Linux x86 NVIDIA Kernel Module 1.0-6629 Wed Nov 3
13:12:51 PST 2004
sr0: scsi3-mmc drive: 40x/40x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
sr1: scsi3-mmc drive: 40x/40x cd/rw xa/form2 cdda tray
Attached scsi CD-ROM sr1 at scsi1, channel 0, id 0, lun 0
sr0: Hmm, seems the drive doesn't support multisession CD's
sr1: Hmm, seems the drive doesn't support multisession CD's
VFS: Can't find ext3 filesystem on dev sr0.
VFS: Can't find ext3 filesystem on dev sr0.
VFS: Can't find ext3 filesystem on dev sr0.
attempt to access beyond end of device
sr0: rw=0, want=68, limit=4
isofs_fill_super: bread failed, dev=sr0, iso_blknum=16, block=16
attempt to access beyond end of device
sr0: rw=0, want=68, limit=4
isofs_fill_super: bread failed, dev=sr0, iso_blknum=16, block=16
--
gentoo-user@gentoo.org mailing list
