On 09/22/10 16:40, me wrote:
> On Wed, Sep 22, 2010 at 7:00 PM, Bill Longman <bill.long...@gmail.com> wrote:
>> I have a new workstation running 64 bits 2.6.34 gentoo sources. It's an
>> HP p6520y (AthlonIIX4) with 6GB and lsusb reports an Alcor Micro 21-in-1
>> Flash Card Reader.
>>
>> I have no usb storage devices plugged in and I see in my dmesg many of
>> the following messages:
>>
>> usb-storage: queuecommand called
>> usb-storage: *** thread awakened.
>> usb-storage: Command TEST_UNIT_READY (6 bytes)
>> usb-storage: 00 00 00 00 00 00
>> usb-storage: Bulk Command S 0x43425355 T 0x5473 L 0 F 0 Trg 0 LUN 1 CL 6
>> usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
>> usb-storage: Status code 0; transferred 31/31
>> usb-storage: -- transfer complete
>> usb-storage: Bulk command transfer result=0
>> usb-storage: Attempting to get CSW...
>> usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
>> usb-storage: Status code 0; transferred 13/13
>> usb-storage: -- transfer complete
>> usb-storage: Bulk status result = 0
>> usb-storage: Bulk Status S 0x53425355 T 0x5473 R 0 Stat 0x1
>> usb-storage: -- transport indicates command failure
>> usb-storage: Issuing auto-REQUEST_SENSE
>> usb-storage: Bulk Command S 0x43425355 T 0x5474 L 18 F 128 Trg 0 LUN 1 CL 6
>> usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
>> usb-storage: Status code 0; transferred 31/31
>> usb-storage: -- transfer complete
>> usb-storage: Bulk command transfer result=0
>> usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries
>> usb-storage: Status code 0; transferred 18/18
>> usb-storage: -- transfer complete
>> usb-storage: Bulk data transfer result 0x0
>> usb-storage: Attempting to get CSW...
>> usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
>> usb-storage: Status code 0; transferred 13/13
>> usb-storage: -- transfer complete
>> usb-storage: Bulk status result = 0
>> usb-storage: Bulk Status S 0x53425355 T 0x5474 R 0 Stat 0x0
>> usb-storage: -- Result from auto-sense is 0
>> usb-storage: -- code: 0xf0, key: 0x2, ASC: 0x3a, ASCQ: 0x0
>> usb-storage: Not Ready: Medium not present
>> usb-storage: scsi cmd done, result=0x2
>> usb-storage: *** thread sleeping.
>>
>> Any ideas who/what is doing this? How to debug?
>>
>> Bill
>>
>> --
>> Bill Longman
>> Εν αρχη ην ο λογος
>>
> I'd guess, at a glance, that you have CONFIG_USB_STORAGE_DEBUG set in
> your kernel config.
>
> To check if that's it (assuming you have /proc/config.gz enabled) run:
> # zgrep CONFIG_USB_STORAGE_DEBUG /proc/config.gz
>
Yep...thanks.
