On Tue, Aug 24, 2010 at 4:27 AM, Mick <michaelkintz...@gmail.com> wrote:
> On 24 August 2010 11:23, Adam Carter <adamcart...@gmail.com> wrote: > > > >> No. I ditched my xorg.conf completely; it had been there just because I > >> couldn't get the Westinghouse monitor to work without it. The Xorg logs > >> show it recognizes a boatload of > >> modes that the monitor likes, but gives an alibi for not using the HD > >> ones. The approach > >> does not seem promising. > >> > >> /var/log/Xorg.0.log attached. I'm paying attention to lines 269 295 327 > >> 369 377 380 and 381 > >> > >> 269: (II) MACH64(0): Modeline "1920x1080"x0.0 148.50 1920 2008 2052 > >> 2200 1080 1084 1089 1125 +hsync +vsync (67.5 kHz) > >> 295: (II) MACH64(0): Modeline "1920x1080"x60.0 172.80 1920 2040 2248 > >> 2576 1080 1081 1084 1118 -hsync +vsync (67.1 kHz) > >> 327: (II) MACH64(0): Estimated virtual size for aspect ratio 1.7931 is > >> 1920x1080 > >> 369: (II) MACH64(0): Not using default mode "1920x1440" (insufficient > >> memory for mode) > >> 377: (II) MACH64(0): Not using driver mode "1920x1080" (bad mode > >> clock/interlace/doublescan) > >> 380: (II) MACH64(0): Not using driver mode "1920x1080" (bad mode > >> clock/interlace/doublescan) > >> 381: (WW) MACH64(0): Shrinking virtual size estimate from 1920x1080 to > >> 1280x1024 > >> > > > > I assume 269 and 295 are related to 377 and 380. I remember i had a lot > of > > pain getting a Geforce 440MX to do 16:9, but it was all in the modelines. > > There are some modeline calculators on the web, but be warned that some > of > > them produce bad output. I did eventually get it to work after a lot of > > trial and error. > > > > Also because of this; > > > > (II) MACH64(0): <default monitor>: Using hsync range of 30.00-85.00 kHz > > (II) MACH64(0): <default monitor>: Using vrefresh range of 55.00-75.00 Hz > > (II) MACH64(0): <default monitor>: Using maximum pixel clock of 160.00 > MHz > > > > > > you may need to set the ranges in your xorg.conf instead. check the > monitors > > specs first tho. > > What does xrandr -q show? > -- > Regards, > Mick > > treat log # xrandr -q Screen 0: minimum 320 x 240, current 1280 x 1024, maximum 1440 x 1024 default connected 1280x1024+0+0 0mm x 0mm 1280x1024 60.0* 1440x900 60.0 1280x960 60.0 1152x864 75.0 1024x768 75.0 70.0 60.0 896x672 60.0 832x624 75.0 800x600 75.0 72.0 60.0 56.0 65.0 700x525 75.0 60.0 640x512 75.0 60.0 640x480 75.0 73.0 67.0 60.0 720x400 70.0 576x432 75.0 512x384 75.0 70.0 60.0 416x312 75.0 400x300 75.0 72.0 60.0 56.0 320x240 75.0 73.0 60.0 treat log # -- Kevin O'Gorman, PhD
