Hello, I'm interested in running the RAMSpeed benchmark http://alasir.com/software/ramspeed/ http://www.alasir.com/software/ramspeed/ramspeed-2.6.0.tar.gz for x86, ideally for both syscall emulation mode and full system mode.
# I installed gem5 cd ~ hg clone http://repo.gem5.org/gem5 cd ~/gem5 scons build/X86/gem5.opt # then I grabbed ramspeed: cd wget http://www.alasir.com/software/ramspeed/ramspeed-2.6.0.tar.gz tar xvzf ramspeed-2.6.0.tar.gz cd ~/ramspeed-2.6.0/ # I created a static binary, gcc -Wl,-O2 -Wl,-s -static -o ramspeed temp/ramspeed.o temp/intmark.o temp/intmem.o temp/fltmark.o temp/fltmem.o temp/mmxmark.o temp/mmxmem.o temp/ssemark.o temp/ssemem.o # trying syscall emulation mode, it fails due to "gettimeofday" being unimplemented bpayne@bpayne-VirtualBox64:~/gem5$ build/X86/gem5.opt configs/example/se.py -c ~/ramspeed-2.6.0/ramspeed -o "-b1" warning: No header file specified for SimObject: Switch gem5 Simulator System. http://gem5.org gem5 is copyrighted software; use the --copyright option for details. gem5 compiled Nov 7 2012 13:26:33 gem5 started Nov 7 2012 14:51:06 gem5 executing on bpayne-VirtualBox64 command line: build/X86/gem5.opt configs/example/se.py -c /home/bpayne/ramspeed-2.6.0/ramspeed -o -b1 Global frequency set at 1000000000000 ticks per second 0: system.remote_gdb.listener: listening for remote gdb #0 on port 7000 **** REAL SIMULATION **** info: Entering event queue @ 0. Starting simulation... warn: instruction 'fnstcw_Mw' unimplemented warn: instruction 'fldcw_Mw' unimplemented RAMspeed (Linux) v2.6.0 by Rhett M. Hollander and Paul V. Bolotoff, 2002-09 8Gb per pass mode fatal: syscall gettimeofday (#96) unimplemented. @ cycle 9162000 [unimplementedFunc:build/X86/sim/syscall_emul.cc, line 83] Memory Usage: 624768 KBytes # since "time" is a central metric in ramspeed.c, I decided to try full system mode # When I use the full system files (img+kernel) available from # http://gem5.org/Download # for x86, # http://www.m5sim.org/dist/current/x86/x86-system.tar.bz2 # http://www.m5sim.org/dist/current/x86/config-x86.tar.bz2 # the kernel is "too old" when ramspeed is run within full system mode: ./ramspeed -b1 FATAL: kernel too old ramspeed[810]: segfault at 00002acb... Segmentation fault I have created an .img file for Ubuntu 12.04 64bit using QEMU and am able to boot into it using QEMU. Then I can run ramspeed to verify it works within the image. My question is where do I get the kernel I need to specify when I run the following: build/X86/gem5.opt configs/example/fs.py --disk-image=/home/bpayne/full_system_images/disks/ubuntu-x86_64_1204.img --kernel=/home/bpayne/full_system_images/binaries/x86_64-vmlinux-2.6.22.9 I tried --kernel=/boot/vmlinux-3.2.0-29-generic which is on the host, but that file is only 5MB (rather than the 50MB kernel which was downloaded from m5sim.org. I have compiled the kernel before, but didn't produce the file gem5 is looking for. Thank you, Ben Payne Laboratory for Physical Sciences http://www.lps.umd.edu/ office: 443-654-7890 _______________________________________________ gem5-users mailing list gem5-users@gem5.org http://m5sim.org/cgi-bin/mailman/listinfo/gem5-users
