I have same motherboard and I tried re patch as follows.
The result is still failed.
http://people.freebsd.org/~yongari/re/re.HEAD.20080624
re0: <RealTek 8101E PCIe 10/100baseTX> port 0x2000-0x20ff mem 0x48200000-0x48200
fff,0x48000000-0x4800ffff irq 16 at device 0.0 on pci1
re0: Chip rev. 0x24800000
re0: MAC rev. 0x00200000
re0: Unknown H/W revision: 0x24800000
device_attach: re0 attach returned 6
Thanks,
Tadashi Takahashi
At 09:52 08/07/08, Pyun YongHyeon wrote:
On Tue, Jul 08, 2008 at 07:35:30AM +0900, NAGATA Shinya wrote:
> > Could you please try 'boot -v' and see if there is some error messages?
>
> 're0' is displayed. But it seems like kernel couldn't find a driver.
> | re0: Reserved 0x100 bytes for rid 0x10 type 4 at 0x2000
> | pci1: <network, ethernet> at device 0.0 (no driver attached)
>
>
> --
> NAGATA Shinya
> Consoles: internal video/keyboard serial port
> BIOS drive C: is disk0
> BIOS 572kB/2085068kB available memory
>
[...]
> found-> vendor=0x10ec, dev=0x8136, revid=0x02
^^^^^^^^^^^^^^^^^^^^^^^^^
This looks like RealTek 8101 PCIe fast ethernet controller.
> bus=1, slot=0, func=0
> class=02-00-00, hdrtype=0x00, mfdev=0
> cmdreg=0x0007, statreg=0x0010, cachelnsz=16 (dwords)
> lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
> intpin=a, irq=11
> powerspec 3 supports D0 D1 D2 D3 current D0
> MSI supports 1 message, 64 bit
> MSI-X supports 2 messages in map 0x20
> map[10]: type 4, range 32, base 00002000, size 8, enabled
> pcib1: requested I/O range 0x2000-0x20ff: in range
> map[18]: type 1, range 64, base 90200000, size 12, enabled
> pcib1: requested memory range 0x90200000-0x90200fff: good
> map[20]: type 3, range 64, base 90000000, size 16, enabled
> pcib1: requested memory range 0x90000000-0x9000ffff: good
> pcib1: matched entry for 1.0.INTA
> pcib1: slot 0 INTA hardwired to IRQ 16
> re0: Reserved 0x100 bytes for rid 0x10 type 4 at 0x2000
> pci1: <network, ethernet> at device 0.0 (no driver attached)
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
This indicates re(4) probe didn't recognize the hardware. I have no
idea why this can happen. Would you try 7-stable? 7-stable changed
device probe/attach routine so it compares PCI device ids in probe
stage intead of allocating resources as 6.x.
--
Regards,
Pyun YongHyeon
_______________________________________________
freebsd-stable@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-stable
To unsubscribe, send any mail to "[EMAIL PROTECTED]"
_______________________________________________
freebsd-stable@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-stable
To unsubscribe, send any mail to "[EMAIL PROTECTED]"
