My system has been working reliably with 6.3 for quite some time... when
I rebooted into single user mode to do the installworld with the
7.0-RELEASE kernel, the install died about halfway through with READ_DMA
TIMEOUT errors. Since I had a mixed system at that point, I set
hw.ata.ata_dma="0" in /boot/loader.conf and completed the install.
After a good boot to verify everything was working, I flipped
hw.ata.ata_dma back and rebooted. The corrupted sync message scared the
heck out of me:
Waiting (max 60 seconds) for system process `vnlru' to stop...done
Waiti
Synncgi n(gm adxi sk6s0, svencoodnedss )r efmoari nsiynsgte.m. .pr1o0c
ess `syncer' to stop...8 7 8 3 3 3 1 0 0 0 0 done
And after the reboot, the READ_DMA timeouts were back.
I installed sysutils/smartmontools (output attached in case it's usefull)
The only "odd" think I can think of about my system is an unusually high
HZ value (2386) I'm building a kernel now with 1000 to check if that
makes a difference.
Copyright (c) 1992-2008 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 7.0-RELEASE #1: Tue Feb 26 22:49:13 PST 2008
[EMAIL PROTECTED]:/usr/obj/usr/src/sys/SERVER
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel Pentium III (996.85-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x686 Stepping = 6
Features=0x387fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,PN,MMX,FXSR,SSE>
real memory = 1207959552 (1152 MB)
avail memory = 1172832256 (1118 MB)
MPTable: <AMI CNB30LE >
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
cpu0 (BSP): APIC ID: 0
cpu1 (AP): APIC ID: 1
ioapic0: Assuming intbase of 0
ioapic1: Assuming intbase of 16
ioapic0 <Version 1.1> irqs 0-15 on motherboard
ioapic1 <Version 1.1> irqs 16-31 on motherboard
kbd1 at kbdmux0
cpu0 on motherboard
cpu1 on motherboard
pcib0: <MPTable Host-PCI bridge> pcibus 0 on motherboard
pci0: <PCI bus> on pcib0
vgapci0: <VGA-compatible display> port 0xd800-0xd8ff mem
0xfd000000-0xfdffffff,0xfeaff000-0xfeafffff irq 22 at device 1.0 on pci0
drm0: <Rage XL> on vgapci0
info: [drm] Initialized mach64 1.0.0 20020904
fxp0: <Intel 82559 Pro/100 Ethernet> port 0xd400-0xd43f mem
0xfeafe000-0xfeafefff,0xfe900000-0xfe9fffff irq 20 at device 4.0 on pci0
miibus0: <MII bus> on fxp0
inphy0: <i82555 10/100 media interface> PHY 1 on miibus0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fxp0: Ethernet address: 00:e0:81:21:49:7e
fxp0: [ITHREAD]
fxp1: <Intel 82559 Pro/100 Ethernet> port 0xd000-0xd03f mem
0xfeafd000-0xfeafdfff,0xfe700000-0xfe7fffff irq 21 at device 5.0 on pci0
miibus1: <MII bus> on fxp1
inphy1: <i82555 10/100 media interface> PHY 1 on miibus1
inphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fxp1: Ethernet address: 00:e0:81:21:49:7f
fxp1: [ITHREAD]
isab0: <PCI-ISA bridge> port 0x580-0x58f at device 15.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <ServerWorks ROSB4 UDMA33 controller> port
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xffa0-0xffaf at device 15.1 on pci0
ata0: <ATA channel 0> on atapci0
ata0: [ITHREAD]
ata1: <ATA channel 1> on atapci0
ata1: [ITHREAD]
ohci0: <OHCI (generic) USB controller> mem 0xfeafc000-0xfeafcfff irq 10
at device 15.2 on pci0
ohci0: [GIANT-LOCKED]
ohci0: [ITHREAD]
usb0: OHCI version 1.0, legacy support
usb0: <OHCI (generic) USB controller> on ohci0
usb0: USB revision 1.0
uhub0: <(0x1166) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0
uhub0: 2 ports with 2 removable, self powered
pcib1: <MPTable Host-PCI bridge> pcibus 1 on motherboard
pci1: <PCI bus> on pcib1
pcm0: <Creative CT5880-C> port 0xef00-0xef3f irq 27 at device 2.0 on pci1
pcm0: <SigmaTel STAC9721/23 AC97 Codec>
pcm0: [ITHREAD]
pcm0: <Playback: DAC1,DAC2 / Record: ADC>
pmtimer0 on isa0
orm0: <ISA Option ROMs> at iomem
0xc0000-0xc7fff,0xc8000-0xc8fff,0xc9000-0xc9fff pnpid ORM0000 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: [ITHREAD]
psm0: model MouseMan+, device ID 0
fdc0: <Enhanced floppy controller> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2
on isa0
fdc0: [FILTER]
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
ppbus0: <Parallel port bus> on ppc0
ppbus0: [ITHREAD]
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppc0: [GIANT-LOCKED]
ppc0: [ITHREAD]
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio0: [FILTER]
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
unknown: <PNP0c01> can't assign resources (memory)
unknown: <PNP0303> can't assign resources (port)
speaker0: <PC speaker> at port 0x61 pnpid PNP0800 on isa0
unknown: <PNP0c02> can't assign resources (port)
unknown: <PNP0f13> can't assign resources (irq)
unknown: <PNP0501> can't assign resources (port)
unknown: <PNP0401> can't assign resources (port)
unknown: <PNP0700> can't assign resources (port)
uhid0: <Logitech Inc. WingMan RumblePad, class 0/0, rev 1.00/1.07, addr
2> on uhub0
uhub0: device problem (IOERROR), disabling port 2
Timecounters tick every 0.838 msec
ipfw2 (+ipv6) initialized, divert enabled, rule-based forwarding
disabled, default to deny, logging disabled
ad0: 239372MB <Maxtor 7Y250P0 YAR41BW0> at ata0-master PIO4
acd0: CDRW <HL-DT-ST GCE-8520B/1.04> at ata1-master UDMA33
SMP: AP CPU #1 Launched!
Trying to mount root from ufs:/dev/ad0s1a
fxp0: Microcode loaded, int_delay: 1000 usec bundle_max: 6
fxp0: Microcode loaded, int_delay: 1000 usec bundle_max: 6
fxp1: Microcode loaded, int_delay: 1000 usec bundle_max: 6
fxp1: Microcode loaded, int_delay: 1000 usec bundle_max: 6
fxp0: Microcode loaded, int_delay: 1000 usec bundle_max: 6
WARNING: attempt to net_add_domain(netgraph) after domainfinalize()
fxp1: Microcode loaded, int_delay: 1000 usec bundle_max: 6
vmnet0: Ethernet address: 00:bd:d3:f1:01:00
vmnet1: Ethernet address: 00:bd:dc:f1:01:01
vmnet2: Ethernet address: 00:bd:de:f1:01:02
vmnet3: Ethernet address: 00:bd:16:f2:01:03
vmnet4: Ethernet address: 00:bd:1e:b9:02:04
vmnet5: Ethernet address: 00:bd:20:b9:02:05
vmnet6: Ethernet address: 00:bd:22:b9:02:06
vmnet7: Ethernet address: 00:bd:23:b9:02:07
bridge0: Ethernet address: da:a1:67:37:d0:c4
fxp0: Microcode loaded, int_delay: 1000 usec bundle_max: 6
fxp0: promiscuous mode enabled
vmnet0: promiscuous mode enabled
vmnet1: promiscuous mode enabled
vmnet2: promiscuous mode enabled
vmnet3: promiscuous mode enabled
Waiting (max 60 seconds) for system process `vnlru' to stop...done
Waiti
Synncgi n(gm adxi sk6s0, svencoodnedss )r efmoari nsiynsgte.m. .pr1o0c
ess `syncer' to stop...8 7 8 3 3 3 1 0 0 0 0 done
Waiting (max 60 seconds) for system process `bufdaemon' to stop...done
All buffers synced.
Uptime: 29m46s
Rebooting...
cpu_reset: Stopping other CPUs
Copyright (c) 1992-2008 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 7.0-RELEASE #1: Tue Feb 26 22:49:13 PST 2008
[EMAIL PROTECTED]:/usr/obj/usr/src/sys/SERVER
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel Pentium III (996.85-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x686 Stepping = 6
Features=0x387fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,PN,MMX,FXSR,SSE>
real memory = 1207959552 (1152 MB)
avail memory = 1172832256 (1118 MB)
MPTable: <AMI CNB30LE >
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
cpu0 (BSP): APIC ID: 0
cpu1 (AP): APIC ID: 1
ioapic0: Assuming intbase of 0
ioapic1: Assuming intbase of 16
ioapic0 <Version 1.1> irqs 0-15 on motherboard
ioapic1 <Version 1.1> irqs 16-31 on motherboard
kbd1 at kbdmux0
cpu0 on motherboard
cpu1 on motherboard
pcib0: <MPTable Host-PCI bridge> pcibus 0 on motherboard
pci0: <PCI bus> on pcib0
vgapci0: <VGA-compatible display> port 0xd800-0xd8ff mem
0xfd000000-0xfdffffff,0xfeaff000-0xfeafffff irq 22 at device 1.0 on pci0
drm0: <Rage XL> on vgapci0
info: [drm] Initialized mach64 1.0.0 20020904
fxp0: <Intel 82559 Pro/100 Ethernet> port 0xd400-0xd43f mem
0xfeafe000-0xfeafefff,0xfe900000-0xfe9fffff irq 20 at device 4.0 on pci0
miibus0: <MII bus> on fxp0
inphy0: <i82555 10/100 media interface> PHY 1 on miibus0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fxp0: Ethernet address: 00:e0:81:21:49:7e
fxp0: [ITHREAD]
fxp1: <Intel 82559 Pro/100 Ethernet> port 0xd000-0xd03f mem
0xfeafd000-0xfeafdfff,0xfe700000-0xfe7fffff irq 21 at device 5.0 on pci0
miibus1: <MII bus> on fxp1
inphy1: <i82555 10/100 media interface> PHY 1 on miibus1
inphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fxp1: Ethernet address: 00:e0:81:21:49:7f
fxp1: [ITHREAD]
isab0: <PCI-ISA bridge> port 0x580-0x58f at device 15.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <ServerWorks ROSB4 UDMA33 controller> port
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xffa0-0xffaf at device 15.1 on pci0
ata0: <ATA channel 0> on atapci0
ata0: [ITHREAD]
ata1: <ATA channel 1> on atapci0
ata1: [ITHREAD]
ohci0: <OHCI (generic) USB controller> mem 0xfeafc000-0xfeafcfff irq 10
at device 15.2 on pci0
ohci0: [GIANT-LOCKED]
ohci0: [ITHREAD]
usb0: OHCI version 1.0, legacy support
usb0: <OHCI (generic) USB controller> on ohci0
usb0: USB revision 1.0
uhub0: <(0x1166) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0
uhub0: 2 ports with 2 removable, self powered
pcib1: <MPTable Host-PCI bridge> pcibus 1 on motherboard
pci1: <PCI bus> on pcib1
pcm0: <Creative CT5880-C> port 0xef00-0xef3f irq 27 at device 2.0 on pci1
pcm0: <SigmaTel STAC9721/23 AC97 Codec>
pcm0: [ITHREAD]
pcm0: <Playback: DAC1,DAC2 / Record: ADC>
pmtimer0 on isa0
orm0: <ISA Option ROMs> at iomem
0xc0000-0xc7fff,0xc8000-0xc8fff,0xc9000-0xc9fff pnpid ORM0000 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: [ITHREAD]
psm0: model MouseMan+, device ID 0
fdc0: <Enhanced floppy controller> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2
on isa0
fdc0: [FILTER]
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
ppbus0: <Parallel port bus> on ppc0
ppbus0: [ITHREAD]
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppc0: [GIANT-LOCKED]
ppc0: [ITHREAD]
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio0: [FILTER]
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
unknown: <PNP0c01> can't assign resources (memory)
unknown: <PNP0303> can't assign resources (port)
speaker0: <PC speaker> at port 0x61 pnpid PNP0800 on isa0
unknown: <PNP0c02> can't assign resources (port)
unknown: <PNP0f13> can't assign resources (irq)
unknown: <PNP0501> can't assign resources (port)
unknown: <PNP0401> can't assign resources (port)
unknown: <PNP0700> can't assign resources (port)
uhid0: <Logitech Inc. WingMan RumblePad, class 0/0, rev 1.00/1.07, addr
2> on uhub0
uhub0: device problem (IOERROR), disabling port 2
Timecounters tick every 0.838 msec
ipfw2 (+ipv6) initialized, divert enabled, rule-based forwarding
disabled, default to deny, logging disabled
ad0: 239372MB <Maxtor 7Y250P0 YAR41BW0> at ata0-master UDMA33
acd0: CDRW <HL-DT-ST GCE-8520B/1.04> at ata1-master UDMA33
SMP: AP CPU #1 Launched!
Trying to mount root from ufs:/dev/ad0s1a
fxp0: Microcode loaded, int_delay: 1000 usec bundle_max: 6
fxp0: Microcode loaded, int_delay: 1000 usec bundle_max: 6
fxp1: Microcode loaded, int_delay: 1000 usec bundle_max: 6
fxp1: Microcode loaded, int_delay: 1000 usec bundle_max: 6
fxp0: Microcode loaded, int_delay: 1000 usec bundle_max: 6
WARNING: attempt to net_add_domain(netgraph) after domainfinalize()
fxp1: Microcode loaded, int_delay: 1000 usec bundle_max: 6
ad0: TIMEOUT - READ_DMA retrying (1 retry left) LBA=56943008
ad0: TIMEOUT - READ_DMA retrying (0 retries left) LBA=56943008
ad0: FAILURE - READ_DMA timed out LBA=56943008
g_vfs_done():ad0s1f[READ(offset=24591417344, length=65536)]error = 5
vnode_pager_getpages: I/O read error
vmnet0: Ethernet address: 00:bd:2e:71:02:00
vmnet1: Ethernet address: 00:bd:3a:71:02:01
vmnet2: Ethernet address: 00:bd:3b:71:02:02
vmnet3: Ethernet address: 00:bd:66:71:02:03
vmnet4: Ethernet address: 00:bd:a6:f0:02:04
vmnet5: Ethernet address: 00:bd:a8:f0:02:05
vmnet6: Ethernet address: 00:bd:a9:f0:02:06
vmnet7: Ethernet address: 00:bd:ab:f0:02:07
bridge0: Ethernet address: e6:d3:5f:ee:dd:23
fxp0: Microcode loaded, int_delay: 1000 usec bundle_max: 6
fxp0: promiscuous mode enabled
vmnet0: promiscuous mode enabled
vmnet1: promiscuous mode enabled
vmnet2: promiscuous mode enabled
vmnet3: promiscuous mode enabled
ad0: TIMEOUT - READ_DMA retrying (1 retry left) LBA=6815744
ad0: TIMEOUT - READ_DMA retrying (0 retries left) LBA=6815744
ad0: FAILURE - READ_DMA timed out LBA=6815744
ad0: TIMEOUT - READ_DMA retrying (1 retry left) LBA=6815744
ad0: TIMEOUT - READ_DMA retrying (0 retries left) LBA=6815744
ad0: FAILURE - READ_DMA timed out LBA=6815744
ad0: TIMEOUT - READ_DMA retrying (1 retry left) LBA=6815744
ad0: TIMEOUT - READ_DMA retrying (0 retries left) LBA=6815744
ad0: FAILURE - READ_DMA timed out LBA=6815744
ad0: TIMEOUT - READ_DMA retrying (1 retry left) LBA=59969424
ad0: TIMEOUT - READ_DMA retrying (0 retries left) LBA=59969424
ad0: FAILURE - READ_DMA timed out LBA=59969424
g_vfs_done():ad0s1f[READ(offset=26140942336, length=65536)]error = 5
vnode_pager_getpages: I/O read error
vm_fault: pager read error, pid 1930 (kdm-bin_greet)
ad0: TIMEOUT - READ_DMA retrying (1 retry left) LBA=155868384
ad0: TIMEOUT - READ_DMA retrying (1 retry left) LBA=155868512
ad0: TIMEOUT - READ_DMA retrying (0 retries left) LBA=155868384
ad0: TIMEOUT - READ_DMA retrying (0 retries left) LBA=155868512
ad0: FAILURE - READ_DMA timed out LBA=155868384
ad0: FAILURE - READ_DMA timed out LBA=155868512
g_vfs_done():ad0s1g[READ(offset=21554118656, length=131072)]error = 5
pid 1930 (kdm-bin_greet), uid 0: exited on signal 11 (core dumped)
smartctl version 5.37 [i386-portbld-freebsd7.0] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Model Family: Maxtor MaXLine Plus II
Device Model: Maxtor 7Y250P0
Serial Number: Y61WGHYE
Firmware Version: YAR41BW0
User Capacity: 251,000,193,024 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 7
ATA Standard is: ATA/ATAPI-7 T13 1532D revision 0
Local Time is: Wed Feb 27 00:45:51 2008 PST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 363) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off
support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 107) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED
WHEN_FAILED RAW_VALUE
3 Spin_Up_Time 0x0027 188 179 063 Pre-fail Always
- 26142
4 Start_Stop_Count 0x0032 253 253 000 Old_age Always
- 147
5 Reallocated_Sector_Ct 0x0033 253 253 063 Pre-fail Always
- 4
6 Read_Channel_Margin 0x0001 253 253 100 Pre-fail Offline
- 0
7 Seek_Error_Rate 0x000a 253 252 000 Old_age Always
- 0
8 Seek_Time_Performance 0x0027 252 245 187 Pre-fail Always
- 58440
9 Power_On_Minutes 0x0032 219 219 000 Old_age Always
- 1052h+05m
10 Spin_Retry_Count 0x002b 253 252 157 Pre-fail Always
- 0
11 Calibration_Retry_Count 0x002b 253 252 223 Pre-fail Always
- 0
12 Power_Cycle_Count 0x0032 253 253 000 Old_age Always
- 251
192 Power-Off_Retract_Count 0x0032 253 253 000 Old_age Always
- 0
193 Load_Cycle_Count 0x0032 253 253 000 Old_age Always
- 0
194 Temperature_Celsius 0x0032 253 253 000 Old_age Always
- 48
195 Hardware_ECC_Recovered 0x000a 253 252 000 Old_age Always
- 11498
196 Reallocated_Event_Count 0x0008 253 253 000 Old_age Offline
- 0
197 Current_Pending_Sector 0x0008 253 253 000 Old_age Offline
- 0
198 Offline_Uncorrectable 0x0008 253 253 000 Old_age Offline
- 0
199 UDMA_CRC_Error_Count 0x0008 199 199 000 Old_age Offline
- 0
200 Multi_Zone_Error_Rate 0x000a 253 252 000 Old_age Always
- 0
201 Soft_Read_Error_Rate 0x000a 253 252 000 Old_age Always
- 14
202 TA_Increase_Count 0x000a 253 252 000 Old_age Always
- 0
203 Run_Out_Cancel 0x000b 253 252 180 Pre-fail Always
- 11
204 Shock_Count_Write_Opern 0x000a 253 252 000 Old_age Always
- 0
205 Shock_Rate_Write_Opern 0x000a 253 252 000 Old_age Always
- 0
207 Spin_High_Current 0x002a 253 252 000 Old_age Always
- 0
208 Spin_Buzz 0x002a 253 252 000 Old_age Always
- 0
209 Offline_Seek_Performnce 0x0024 198 194 000 Old_age Offline
- 0
99 Unknown_Attribute 0x0004 253 253 000 Old_age Offline
- 0
100 Unknown_Attribute 0x0004 253 253 000 Old_age Offline
- 0
101 Unknown_Attribute 0x0004 253 253 000 Old_age Offline
- 0
SMART Error Log Version: 1
ATA Error Count: 2
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 2 occurred at disk power-on lifetime: 5171 hours (215 days + 11 hours)
When the command that caused the error occurred, the device was in an unknown
state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 10 80 00 c8 e6 Error: UNC 16 sectors at LBA = 0x06c80080 = 113770624
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 10 80 00 c8 e6 08 00:13:29.312 READ DMA
c8 00 04 98 14 02 e0 08 00:13:18.144 READ DMA
c8 00 04 3c 69 06 e0 08 00:13:18.144 READ DMA
c8 00 10 50 44 06 e0 08 00:13:09.008 READ DMA
c8 00 0c 80 14 04 e0 08 00:13:09.008 READ DMA
Error 1 occurred at disk power-on lifetime: 5171 hours (215 days + 11 hours)
When the command that caused the error occurred, the device was in an unknown
state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 10 80 00 c8 e6 Error: UNC 16 sectors at LBA = 0x06c80080 = 113770624
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 10 80 00 c8 e6 08 00:13:07.840 READ DMA
c8 00 01 00 00 00 e0 08 00:13:07.840 READ DMA
c8 00 02 00 00 00 e0 08 00:13:07.840 READ DMA
c8 00 01 01 00 00 e0 08 00:13:07.840 READ DMA
c8 00 04 00 01 06 e0 08 00:13:07.840 READ DMA
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours)
LBA_of_first_error
# 1 Short offline Completed without error 00% 394 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
_______________________________________________
freebsd-stable@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-stable
To unsubscribe, send any mail to "[EMAIL PROTECTED]"
