On 1/10/07, Bruce A. Mah <[EMAIL PROTECTED]> wrote:
If memory serves me right, LI Xin wrote:
> Not sure if the snapshot contained the changes, though... IIRC the
> January snapshot is not released yet?
The January CURRENT snapshots are being built and uploaded now. The
mirrors might have some of the architectures, but an announcement will
come only after everything's been uploaded (and had a little while to
propagate).
I just booted the january/amd64 snapshot ISO and it detects it fine:
++++++++++++++++++++++++
pcib3: <ACPI PCI-PCI bridge> irq 16 at device 28.4 on pci0
pcib3: secondary bus 3
pcib3: subordinate bus 3
pcib3: I/O decode 0x9000-0x9fff
pcib3: memory decode 0xf9000000-0xfaffffff
pcib3: no prefetched decode
pci3: <ACPI PCI bus> on pcib3
pci3: physical bus=3
found-> vendor=0x11ab, dev=0x4362, revid=0x22
bus=3, slot=0, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0010, cachelnsz=8 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=10
powerspec 2 supports D0 D1 D2 D3 current D0
VPD Ident: Marvell Yukon 88E8053 Gigabit Ethernet Controller
PN: Yukon 88E8053
EC: Rev. 2.2
MN: Marvell
SN: AbCdEfG83CD03
CP: id 1, BAR16, off 0x3cc
RV: 0x6c
MSI supports 2 messages, 64 bit
map[10]: type 1, range 64, base 0xfa000000, size 14, enabled
pcib3: requested memory range 0xfa000000-0xfa003fff: good
map[18]: type 4, range 32, base 0x9000, size 8, enabled
pcib3: requested I/O range 0x9000-0x90ff: in range
pcib3: matched entry for 3.0.INTA
pcib3: slot 0 INTA hardwired to IRQ 16
mskc0: <Marvell Yukon 88E8053 Gigabit Ethernet> port 0x9000-0x90ff mem
0xfa000000-0xfa003fff irq 16 at device 0.0 on pci3
mskc0: Reserved 0x4000 bytes for rid 0x10 type 3 at 0xfa000000
mskc0: MSI count : 2
mskc0: attempting to allocate 2 MSI vectors (2 supported)
mskc0: using IRQs 258259 for MSI
mskc0: RAM buffer size : 48KB
mskc0: Port 0 : Rx Queue 32KB(0x00000000:0x00007fff)
mskc0: Port 0 : Tx Queue 16KB(0x00008000:0x0000bfff)
msk0: <Marvell Technology Group Ltd. Yukon EC Id 0xb6 Rev 0x02> on mskc0
msk0: bpf attached
msk0: Ethernet address: 00:16:e6:83:cd:03
miibus0: <MII bus> on msk0
e1000phy0: <Marvell 88E1111 Gigabit PHY> on miibus0
e1000phy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX-FDX, auto
mskc0: [MPSAFE]
mskc0: [FAST]
+++++++++++++++
Thanks.
Bruce.
cheers
mars
_______________________________________________
freebsd-stable@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-stable
To unsubscribe, send any mail to "[EMAIL PROTECTED]"
