On Wed, Nov 08, 2006 at 07:39:52PM -0700, Scott Long wrote:
> Is the firewire controller something that you can disable? Can you
> selectively disable some of the USB controllers?
>
> Scott
>
I've tried disabling every combination of devices possible. The only
change that fixed the problem (surprise, surprise) was disabling the
integrated em NIC and or the nvidia card. I don't have another PCI
express video board to swap with unfortunatly; so, I can't test that
route.
I should mention that disabling acpi also works, but it appears that SMP
won't work without acpi.
vmstat -i without apic:
interrupt total rate
irq0: clk 1371151 999
irq1: atkbd0 288 0
irq5: ehci0 1 0
irq6: fdc0 11 0
irq7: ppc0 6 0
irq8: rtc 175479 127
irq9: uhci2 acpi0+ 6204 4
irq11: nvidia0 em* 610237 444
irq14: ata0 17 0
irq15: ata1 48 0
Total 2163442 1576
Oddly, the dmesg output is the same weither or not the apics are enabled
or not?
Copyright (c) 1992-2006 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 6.2-PRERELEASE #0: Wed Nov 8 16:01:29 PST 2006
[EMAIL PROTECTED]:/usr/obj/usr/src/sys/CSERV65.SMP
MPTable: <DELL WS 670 >
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Xeon(TM) CPU 3.00GHz (2992.51-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0xf43 Stepping = 3
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
Features2=0x641d<SSE3,RSVD2,MON,DS_CPL,CNTX-ID,CX16,<b14>>
AMD Features=0x20100000<NX,LM>
Logical CPUs per core: 2
real memory = 1072209920 (1022 MB)
avail memory = 1035890688 (987 MB)
pnpbios: Bad PnP BIOS data checksum
ioapic0: Changing APIC ID to 8
ioapic0: Assuming intbase of 0
ioapic1: Changing APIC ID to 9
ioapic1: Assuming intbase of 24
ioapic2: Changing APIC ID to 10
ioapic2: Assuming intbase of 48
ioapic0 <Version 2.0> irqs 0-23 on motherboard
ioapic1 <Version 2.0> irqs 24-47 on motherboard
ioapic2 <Version 2.0> irqs 48-71 on motherboard
kbd1 at kbdmux0
kqemu version 0x00010300
kqemu: KQEMU installed, max_locked_mem=517120kB.
cpu0 on motherboard
pcib0: <MPTable Host-PCI bridge> pcibus 0 on motherboard
pci0: <PCI bus> on pcib0
pcib0: unable to route slot 2 INTA
pcib0: unable to route slot 3 INTA
pcib0: unable to route slot 4 INTA
pci0: <unknown> at device 0.1 (no driver attached)
pcib1: <PCI-PCI bridge> irq 11 at device 2.0 on pci0
pci1: <PCI bus> on pcib1
pcib2: <MPTable PCI-PCI bridge> at device 0.0 on pci1
pci2: <PCI bus> on pcib2
pcib3: <MPTable PCI-PCI bridge> at device 0.2 on pci1
pci3: <PCI bus> on pcib3
em0: <Intel(R) PRO/1000 Network Connection Version - 6.2.9> port 0xdcc0-0xdcff
mem 0xdfee0000-0xdfefffff irq 48 at device 14.0 on pci3
em0: Ethernet address: 00:13:72:78:b9:e3
pcib4: <MPTable PCI-PCI bridge> irq 11 at device 3.0 on pci0
pci4: <PCI bus> on pcib4
pcib5: <MPTable PCI-PCI bridge> irq 11 at device 4.0 on pci0
pci5: <PCI bus> on pcib5
nvidia0: <Quadro PCI-E Series> mem
0xdd000000-0xddffffff,0xc0000000-0xcfffffff,0xde000000-0xdeffffff irq 16 at
device 0.0 on pci5
nvidia0: [GIANT-LOCKED]
uhci0: <Intel 82801EB (ICH5) USB controller USB-A> port 0xff80-0xff9f irq 16 at
device 29.0 on pci0
uhci0: [GIANT-LOCKED]
usb0: <Intel 82801EB (ICH5) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <Intel 82801EB (ICH5) USB controller USB-B> port 0xff60-0xff7f irq 19 at
device 29.1 on pci0
uhci1: [GIANT-LOCKED]
usb1: <Intel 82801EB (ICH5) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <Intel 82801EB (ICH5) USB controller USB-C> port 0xff40-0xff5f irq 18 at
device 29.2 on pci0
uhci2: [GIANT-LOCKED]
usb2: <Intel 82801EB (ICH5) USB controller USB-C> on uhci2
usb2: USB revision 1.0
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhci3: <Intel 82801EB (ICH5) USB controller USB-D> port 0xff20-0xff3f irq 16 at
device 29.3 on pci0
uhci3: [GIANT-LOCKED]
usb3: <Intel 82801EB (ICH5) USB controller USB-D> on uhci3
usb3: USB revision 1.0
uhub3: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
ehci0: <Intel 82801EB/R (ICH5) USB 2.0 controller> mem 0xffa80800-0xffa80bff
irq 23 at device 29.7 on pci0
ehci0: [GIANT-LOCKED]
usb4: waiting for BIOS to give up control
usb4: EHCI version 1.0
usb4: companion controllers, 2 ports each: usb0 usb1 usb2 usb3
usb4: <Intel 82801EB/R (ICH5) USB 2.0 controller> on ehci0
usb4: USB revision 2.0
uhub4: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub4: 8 ports with 8 removable, self powered
pcib6: <MPTable PCI-PCI bridge> at device 30.0 on pci0
pci6: <PCI bus> on pcib6
fwohci0: <Texas Instruments TSB43AB22/A> mem
0xdcffb800-0xdcffbfff,0xdcffc000-0xdcffffff irq 16 at device 12.0 on pci6
fwohci0: OHCI version 1.10 (ROM=0)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 80:78:00:13:b9:e3:72:00
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
sbp0: <SBP-2/SCSI over FireWire> on firewire0
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 82:78:00:e3:72:00
fwe0: Ethernet address: 82:78:00:e3:72:00
fwe0: if_start running deferred for Giant
fwohci0: Initiate bus reset
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire0: bus manager 0 (me)
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH5 UDMA100 controller> port
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xffa0-0xffaf mem 0xdffffc00-0xdfffffff irq
18 at device 31.1 on pci0
ata0: <ATA channel 0> on atapci0
ata1: <ATA channel 1> on atapci0
atapci1: <Intel ICH5 SATA150 controller> port
0xfe00-0xfe07,0xfe10-0xfe13,0xfe20-0xfe27,0xfe30-0xfe33,0xfea0-0xfeaf irq 18 at
device 31.2 on pci0
ata2: <ATA channel 0> on atapci1
ata3: <ATA channel 1> on atapci1
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
pcm0: <Intel ICH5 (82801EB)> port 0xec00-0xecff,0xe8c0-0xe8ff mem
0xdffffa00-0xdffffbff,0xdffff900-0xdffff9ff irq 17 at device 31.5 on pci0
pcm0: <Analog Devices AD1981B AC97 Codec>
pmtimer0 on isa0
orm0: <ISA Option ROMs> at iomem
0xc0000-0xcbfff,0xcc000-0xcd7ff,0xcd800-0xcffff on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
fdc0: <Enhanced floppy controller> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: [FAST]
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
ukbd0: DELL DELL USB Keyboard, rev 1.10/1.05, addr 2, iclass 3/1
kbd2 at ukbd0
ums0: Logitech Optical USB Mouse, rev 2.00/3.40, addr 3, iclass 3/1
ums0: 3 buttons and Z dir.
Timecounter "TSC" frequency 2992511138 Hz quality 800
Timecounters tick every 1.000 msec
ad0: 38166MB <WDC WD400BB-53AUA1 18.20D18> at ata0-master UDMA100
acd0: CDRW <TSSTcorp CD-RW/DVD-ROM TS-H492C/DE02> at ata1-master UDMA33
ad4: 76293MB <SAMSUNG HD080HJ/P ZH100-34> at ata2-master SATA150
Trying to mount root from ufs:/dev/ad4s1a
WARNING: /home was not properly dismounted
WARNING: /tmp was not properly dismounted
WARNING: /usr was not properly dismounted
WARNING: /var was not properly dismounted
bridge0: Ethernet address: 5a:8f:36:b8:41:7c
netsmb_dev: loaded
--
Russell A. Jackson <[EMAIL PROTECTED]>
Network Analyst
California State University, Bakersfield
_______________________________________________
freebsd-stable@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-stable
To unsubscribe, send any mail to "[EMAIL PROTECTED]"
