----- Original Message -----
From: "Andy Jema" <[EMAIL PROTECTED]>
To: <[EMAIL PROTECTED]>
Cc: <freebsd-stable@freebsd.org>
Sent: Wednesday, March 22, 2006 6:07 AM
Subject: (no subject)
Hello!
I gave a new try to 6.1-BETA4 on my Blade 150 recently but
there are some errors still spitting out during an installation:
acd0: TIMEOUT - READ_BIG retrying (1 retry left)
Interrupt storm detected on "vec1996:"; throttling interrupt source
acd0: TIMEOUT - READ_BIG retrying (1 retry left)
hw.ata.atapi_dma to 0
dmesg:
Sun Blade 150 (UltraSPARC-IIe 650MHz), No Keyboard
Copyright 1998-2002 Sun Microsystems, Inc. All rights reserved.
OpenBoot 4.6, 512 MB memory installed, Serial #53155393.
Ethernet address 0:3:ba:2b:16:41, Host ID: 832b1641.
Rebooting with command: boot cdrom
Boot device: /[EMAIL PROTECTED],0/[EMAIL PROTECTED]/[EMAIL PROTECTED],0:f File
and args:
Perhaps similarly:
http://groups.google.com/group/mailing.freebsd.current/browse_frm/thread/4953b4952a84db2d/8498b3cbc5b01ca1#8498b3cbc5b01ca1
Why I think it's related:
timeouts and interrupt storm in ata,
only since 6.1beta4 or very recently before that (6.0stable-snap011 was
fine)
only when CPUTYPE is not ix86
In this case the hardware is x86 (athlonxp) so it looks like it's merely
changing CPUTYPE that breaks it.
Changing cputype from stock to i686 does not break it.
athlon-xp is kind of silly and makes little performance difference as far as
I can tell for the things I do on that box so i686 is fine, but yours, mine
& some other recent messages just looks like a pattern to me.
Brian K. White -- [EMAIL PROTECTED] -- http://www.aljex.com/bkw/
+++++[>+++[>+++++>+++++++<<-]<-]>>+.>.+++++.+++++++.-.[>+<---]>++.
filePro BBx Linux SCO FreeBSD #callahans Satriani Filk!
FreeBSD/sparc64 boot block
Boot path: /[EMAIL PROTECTED],0/[EMAIL PROTECTED]/[EMAIL PROTECTED],0:f
Boot loader: /boot/loader
Consoles: Open Firmware console
Boot path set to /[EMAIL PROTECTED],0/[EMAIL PROTECTED]/[EMAIL PROTECTED],0:a
FreeBSD/sparc64 bootstrap loader, Revision 1.0
([EMAIL PROTECTED], Thu Mar 16 00:29:29 UTC 2006)
bootpath="/[EMAIL PROTECTED],0/[EMAIL PROTECTED]/[EMAIL PROTECTED],0:a"
Loading /boot/defaults/loader.conf
/boot/kernel/kernel data=0x490f08+0x5bbb8 syms=[0x8+0x63960+0x8+0x5396f]
/
Hit [Enter] to boot immediately, or any other key for command prompt.
Booting [/boot/kernel/kernel]...
nothing to autoload yet.
jumping to kernel entry at 0xc0060000.
Copyright (c) 1992-2006 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 6.1-BETA4 #0: Thu Mar 16 15:20:20 UTC 2006
[EMAIL PROTECTED]:/usr/obj/usr/src/sys/GENERIC
Timecounter "tick" frequency 650000000 Hz quality 1000
real memory = 536870912 (512 MB)
avail memory = 506642432 (483 MB)
cpu0: Sun Microsystems UltraSparc-IIe Processor (650.00 MHz CPU)
nexus0: <Open Firmware Nexus device>
pcib0: <U2P UPA-PCI bridge> on nexus0
pcib0: Hummingbird compatible, impl 0, version 0, ign 0x7c0, bus A
pcib0: [FAST]
pcib0: [FAST]
pcib0: [GIANT-LOCKED]
pcib0: [GIANT-LOCKED]
pcib0 dvma: DVMA map: 0xc0000000 to 0xc3ffffff
pci0: <OFW PCI bus> on pcib0
ebus0: <PCI-EBus3 bridge> mem 0xf0000000-0xf0ffffff,0xf1000000-0xf17fffff
at device 12.0 on pci0
ebus0: <idprom>: incomplete
ebus0: <flashprom> addr 0-0xfffff (no driver attached)
eeprom0: <EEPROM/clock> addr 0x100000000-0x100001fff on ebus0
eeprom0: model mk48t59
eeprom0: hostid 832b1641
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
gem0: <Sun ERI 10/100 Ethernet Adaptor> mem 0x400000-0x41ffff at device
12.1 on pci0
miibus0: <MII bus> on gem0
ukphy0: <Generic IEEE 802.3u media interface> on miibus0
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
gem0: 2kB RX FIFO, 2kB TX FIFO
gem0: Ethernet address: 00:03:ba:2b:16:41
fwohci0: <Sun PCIO-2> mem 0x420000-0x4207ff,0x422000-0x4227ff at device
12.2 on pci0
fwohci0: OHCI version 1.0 (ROM=0)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:03:ba:ff:fe:2b:16:41
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
sbp0: <SBP-2/SCSI over FireWire> on firewire0
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 02:03:ba:2b:16:41
fwe0: Ethernet address: 02:03:ba:2b:16:41
fwe0: if_start running deferred for Giant
fwohci0: Initiate bus reset
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire0: bus manager 0 (me)
ohci0: <Sun PCIO-2 USB controller> mem 0x2000000-0x2007fff at device 12.3
on pci0
ohci0: [GIANT-LOCKED]
usb0: OHCI version 1.0, legacy support
usb0: <Sun PCIO-2 USB controller> on ohci0
usb0: USB revision 1.0
uhub0: (0x108e) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 4 ports with 4 removable, self powered
pci0: <old, non-VGA display device> at device 3.0 (no driver attached)
pci0: <multimedia, audio> at device 8.0 (no driver attached)
atapci0: <AcerLabs M5229 UDMA66 controller> port
0xa00-0xa07,0xa18-0xa1b,0xa10-0xa17,0xa08-0xa0b,0xa20-0xa2f at device 13.0
on pci0
atapci0: using PIO transfers above 137GB as workaround for 48bit DMA
access bug, expect reduced performance
ata2: <ATA channel 0> on atapci0
ata3: <ATA channel 1> on atapci0
pcib1: <OFW PCI-PCI bridge> at device 5.0 on pci0
pci1: <OFW PCI bus> on pcib1
machfb0: <ATI Rage XL> port 0xb00-0xbff mem
0x3000000-0x3ffffff,0x426000-0x426fff at device 19.0 on pci0
machfb0: 16 MB aperture at 0xd5d14000, 1 KB registers at 0x037ffc00
machfb0: 8188 KB SDRAM 114.992 MHz, maximum RAMDAC clock 230 MHz, DSP
machfb0: resolution 1152x900 at 8 bpp
syscons0: <System console> on nexus0
syscons0: Unknown <16 virtual consoles, flags=0x100>
uart0: <16550 or compatible> at port 0x3f8-0x3ff irq 43 on isa0
uart0: console (9600,n,8,1)
uart1: <16550 or compatible> at port 0x2e8-0x2ef irq 43 on isa0
Timecounters tick every 1.000 msec
md0: Preloaded image </boot/mfsroot> 4194304 bytes at 0xc05a3da0
ad0: 38166MB <WDC WD400BB-22DEA0 05.03E05> at ata2-master UDMA66
acd0: CDRW <SONY CD-ROM CDU523 1/Ver 52BS> at ata2-slave UDMA66
Trying to mount root from ufs:/dev/md0
/stand/sysinstall running as init on serial console
Setting hw.ata.atapi_dma to 0 gives no luck :(
Sincerely yours,
Andy
_______________________________________________
freebsd-stable@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-stable
To unsubscribe, send any mail to "[EMAIL PROTECTED]"
_______________________________________________
freebsd-stable@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-stable
To unsubscribe, send any mail to "[EMAIL PROTECTED]"
