Dear Paters, Thank you for your reply.
From: Wes Peters <[EMAIL PROTECTED]> Subject: Re: bge drivers does not work for 3COM 3C996-SX / 3C996B-T Date: Sun, 28 Dec 2003 20:59:47 -0800 Message-ID: <[EMAIL PROTECTED]> > On Sunday 28 December 2003 04:01 am, Hideki Yamamoto wrote: > > Hi, > > > > I tried today's 4.9-stable on a FreeBSD box with two 3COM 3C996-SXs and > > two onboard BMC5703 chips. 3COM 3C996-SX boards are linkup, but the > > other side, an SX I/F on SUN F280 is not linkup. > > When doing ping command to SUN, LED on 3C996 are brinking but > > nothing happens to SUN board. > > I changed bge0 to bge2, but the situation is the same. > > Hardware diagram is as follows. bge0 can connect to the router or > > another PC with intel SX board. > > Is this related to AUTO negotiation? I cannot find any parameters > > about AUTO negotiation in 'bge' driver source. > > > > Any help would be greatly appreciated. > > > > Hideki Yamamoto > > > > +--------------+ > > > > | (bge0)3C996-SX+-----+[Router] > > | > > | (bge2)3C996-SX+-----+[SUN F280] > > > > +--------------+ > > > > bge0: <Broadcom BCM5701 Gigabit Ethernet, ASIC rev. 0x105> mem > > 0xf7ef0000-0xf7efffff irq 10 at device 1.0 on pci1 bge0: Ethernet > > address: 00:04:76:e1:06:cf > > No miibus or PHY on bge0? Sorry, I cannot answer because my knowledge is not sufficient. > > bge1: <Broadcom BCM5703 Gigabit Ethernet, ASIC rev. 0x1002> mem > > 0xf7ee0000-0xf7eeffff irq 11 at device 2.0 on pci1 bge1: Ethernet > > address: 00:0b:cd:d2:b0:40 > > miibus0: <MII bus> on bge1 > > brgphy0: <BCM5703 10/100/1000baseTX PHY> on miibus0 > > brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, > > 1000baseTX-FDX, auto pcib2: <Host to PCI bridge> on motherboard > > Apparently this is a copper (1000baseTX) card, right? Yes. Both bge1 and bge3 are onboard 1000/100/10base copper cards. These are based on BCM5703. Both bge0 and bge2 are SX cards. > > bge2: <Broadcom BCM5701 Gigabit Ethernet, ASIC rev. 0x105> mem > > 0xf7ff0000-0xf7ffffff irq 15 at device 1.0 on pci4 bge2: Ethernet > > address: 00:0a:5e:1d:83:25 > > bge3: <Broadcom BCM5703 Gigabit Ethernet, ASIC rev. 0x1002> mem > > 0xf7fe0000-0xf7feffff irq 16 at device 2.0 on pci4 bge3: Ethernet > > address: 00:0b:cd:d2:b0:3b > > Again, no miibus or PHY on bge2 and bge3? Are these both SX cards? Would you tell me how to gathere additional information? > Where am I, and what am I doing in this handbasket? > > Wes Peters [EMAIL PROTECTED] > Regards, Hideki Yamamoto _______________________________________________ [EMAIL PROTECTED] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-stable To unsubscribe, send any mail to "[EMAIL PROTECTED]"
