> dmesg output and mptable output would go a long ways towards somebody
> being able to help you.
For my system these are attached at the end of this email.
> I seem to remember that you said the machines used to work just fine.
> It would be helpful for you to bracket the breakage to a smaller
> window of time using CVS & doing a binary search on the source trees,
> looking for the date the breakage occured.
Somewhat harder - I was a bit blase about that update as I had tried
it on several other systems first, so I can tell you that for me it
started on April 8th, but I cannot remember when I updated before that,
so I cannot give you a date when it was actually working :-( Maybe one
of the others with the problem could narrow it down a little further ?
-pcf. [note that I have since updated to RC-1 to see if this makes any
difference to the stability, and I am no longer running SMP]
--------------------------------------------------------------------
dmesg:
Copyright (c) 1992-2002 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.6-RC #0: Fri May 17 15:57:38 BST 2002
[EMAIL PROTECTED]:/usr/obj/usr/src/sys/TIXLINK1
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium III/Pentium III Xeon/Celeron (548.55-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x673 Stepping = 3
Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,
PAT,PSE36,MMX,FXSR,SSE>
real memory = 268435456 (262144K bytes)
avail memory = 256303104 (250296K bytes)
Preloaded elf kernel "kernel" at 0xc04ca000.
netsmb_dev: loaded
Pentium Pro MTRR support enabled
md0: Malloc disk
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Intel 82443BX host to PCI bridge (AGP disabled)> on motherboard
pci0: <PCI bus> on pcib0
pci0: <Cirrus Logic GD5446 SVGA controller> at 11.0
pcib1: <DEC 21150 PCI-PCI bridge> at device 13.0 on pci0
pci1: <PCI bus> on pcib1
tl0: <Compaq Netelligent 10/100 Proliant> port 0x3800-0x380f mem 0xc6ffddf0-0xc6ffd
dff irq 11 at device 7.0 on pci1
tl0: Ethernet address: 00:50:8b:8b:de:ab
miibus0: <MII bus> on tl0
nsphy0: <DP83840 10/100 media interface> on miibus0
nsphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
tlphy0: <ThunderLAN 10baseT media interface> on miibus0
tlphy0: 10base2/BNC, 10base5/AUI
sym0: <875> port 0x3000-0x30ff mem 0xc6fff000-0xc6ffffff,0xc6ffdf00-0xc6ffdfff irq
15 at device 9.0 on pci1
sym0: No NVRAM, ID 7, Fast-20, SE, parity checking
sym1: <875> port 0x3400-0x34ff mem 0xc6ffe000-0xc6ffefff,0xc6ffde00-0xc6ffdeff irq
9 at device 9.1 on pci1
sym1: No NVRAM, ID 7, Fast-20, SE, parity checking
pci0: <unknown card> (vendor=0x0e11, dev=0xa0f0) at 14.0
tl1: <Compaq Netelligent 10/100> port 0x2000-0x200f mem 0xc6efeef0-0xc6efeeff irq 5
at device 15.0 on pci0
tl1: Ethernet address: 00:08:c7:84:c7:4e
miibus1: <MII bus> on tl1
nsphy1: <DP83840 10/100 media interface> on miibus1
nsphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
tlphy1: <ThunderLAN 10baseT media interface> on miibus1
tlphy1: 10base2/BNC, 10base5/AUI
isab0: <Intel 82371AB PCI to ISA bridge> at device 20.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 ATA33 controller> port 0xf100-0xf10f at device 20.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
uhci0: <Intel 82371AB/EB (PIIX4) USB controller> irq 0 at device 20.2 on pci0
uhci0: Could not map ports
device_probe_and_attach: uhci0 attach returned 6
chip1: <Intel 82371AB Power management controller> at device 20.3 on pci0
eisa0: <EISA bus> on motherboard
mainboard0: <CPQ0689 (System Board)> on eisa0 slot 0
orm0: <Option ROMs> at iomem 0xc0000-0xc7fff,0xe8000-0xedfff,0xee000-0xeffff on isa
0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0: cannot reserve I/O port range
Waiting 15 seconds for SCSI devices to settle
sa0 at sym1 bus 0 target 12 lun 0
sa0: <ARCHIVE Python 06240-XXX 8040> Removable Sequential Access SCSI-3 device
sa0: 40.000MB/s transfers (20.000MHz, offset 16, 16bit)
da0 at sym0 bus 0 target 0 lun 0
da0: <COMPAQ AD009322B9 3A07> Fixed Direct Access SCSI-2 device
da0: 40.000MB/s transfers (20.000MHz, offset 15, 16bit), Tagged Queueing Enabled
da0: 8678MB (17773500 512 byte sectors: 255H 63S/T 1106C)
da1 at sym0 bus 0 target 1 lun 0
da1: <COMPAQ AD009322B9 3A07> Fixed Direct Access SCSI-2 device
da1: 40.000MB/s transfers (20.000MHz, offset 15, 16bit), Tagged Queueing Enabled
da1: 8678MB (17773500 512 byte sectors: 255H 63S/T 1106C)
Mounting root from ufs:/dev/da0a
tl0: tx underrun -- increasing tx threshold to 512 bytes
tl0: tx underrun -- increasing tx threshold to 1024 bytes
tl0: tx underrun -- increasing tx threshold to 1280 bytes
mptable:
===============================================================================
MPTable, version 2.0.15
-------------------------------------------------------------------------------
MP Floating Pointer Structure:
location: BIOS
physical address: 0x000f4ff0
signature: '_MP_'
length: 16 bytes
version: 1.4
checksum: 0x9f
mode: Virtual Wire
-------------------------------------------------------------------------------
MP Config Table Header:
physical address: 0x000fc131
signature: 'PCMP'
base table length: 260
version: 1.4
checksum: 0xd7
OEM ID: 'COMPAQ '
Product ID: 'PROLIANT '
OEM table pointer: 0x00000000
OEM table size: 0
entry count: 24
local APIC address: 0xfee00000
extended table length: 76
extended table checksum: 86
-------------------------------------------------------------------------------
MP Config Base Table Entries:
--
Processors: APIC ID Version State Family Model Step Flags
1 0x10 BSP, usable 6 7 3 0x383fbff
0 0x10 AP, usable 6 7 3 0x383fbff
--
Bus: Bus ID Type
0 PCI
1 PCI
9 ISA
--
I/O APICs: APIC ID Version State Address
8 0x11 usable 0xfec00000
--
I/O Ints: Type Polarity Trigger Bus ID IRQ APIC ID PIN#
INT active-hi edge 9 1 8 1
INT active-hi edge 9 0 8 2
INT active-hi edge 9 3 8 3
INT active-hi edge 9 4 8 4
INT active-hi level 9 5 8 5
INT active-hi edge 9 6 8 6
INT active-hi edge 9 7 8 7
INT active-hi edge 9 8 8 8
INT active-hi level 9 9 8 9
INT active-hi edge 9 10 8 10
INT active-hi level 9 11 8 11
INT active-hi edge 9 12 8 12
INT active-lo edge 9 13 8 13
INT active-hi edge 9 14 8 14
INT active-hi level 9 15 8 15
--
Local Ints: Type Polarity Trigger Bus ID IRQ APIC ID PIN#
ExtINT conforms conforms 9 0 255 0
NMI conforms conforms 9 0 255 1
-------------------------------------------------------------------------------
MP Config Extended Table Entries:
Extended Table HOSED!
To Unsubscribe: send mail to [EMAIL PROTECTED]
with "unsubscribe freebsd-stable" in the body of the message
