|
Hello, About 2 weeks ago I upgraded my linux
box to a freebsd machine with a abit bp6 mobo, 2 celleron 533mhz cpus, 256m ram, and a 60gig maxtor hd. I keep
getting the error READ command timeout tag=0 serv=0 - resetting. below is more details and at the bottom is my dmesg.I am EXTREAMLY frustrated about to go nuts trying to pinpoint the
problem. To sum it up – PROBLEM: operating system getting read timeouts from the
drive and resetting it. (the actually error in /var/messages
is ad6: READ command timeout
tag=0 serv=0 – resetting) When this happens it haults the machine and
continues until its happy with the reset of the drive. It is very random when it happens..
sometimes goes days or hours or seconds. MY TROUBLESHOOTING: Have moved the drive from initial ata33
controller to ata66 udma controller and using a brand new high density cable. I have re-compiled
the kernel manytimes, I have disconnected all other drives including
floppy and recompiled kernel. Disabled ata from kernel and
recompiled.. all getting same resulting random hardrive device timing out.
WHAT I THINK IT COULD BE: Bad Hard Drive – The hard drive is brand new and is
not hot to the touch at all when
it panics or crashes but it does make a lot of grinding noises when
this is occouring I was told from the person at the server. Some Weird unstable ata code with FreeBSD. - http://www.google.com/search?hl=en&q=READ+command+timeout+tag%3D0+serv%3D0+-+resetting&btnG=Google+Search will show you
TONS of other people using freeebsd who have had the same problem or
close to it but no answers except to run in PIO mode but even in
that I get the same error. Bad Power Supply: When the drive causes a kernel
panic… upon reboot the bios shows
no hardrive. You have to switch power leads from the supply to get it
to come back, even if it’s the same one you used before. I know bad
power supplies can make some fruity shit happen and a bitch to trouble
shoot. Just for notes... the hardrive is
a brand new Maxtor 60 gig drive. The case is brand
new with a 350w power supply. The motherboard/ram/cpus came out of a
working linux server. Any Sugestions would be VERY MUCH
appreciated! my dmesg is as follows: Copyright (c) 1992-2002 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991,
1992, 1993, 1994 The Regents of the reserved. FreeBSD 4.5-RELEASE #0: Fri May 10 [EMAIL PROTECTED]:/usr/src/sys/compile/MOO Timecounter "i8254" frequency
1193182 Hz CPU: Pentium II/Pentium II Xeon/Celeron (534.55-MHz
686-class CPU) Origin = "GenuineIntel" Id = 0x665 Stepping = 5 Features=0x183fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR> real memory = 268435456 (262144K bytes) avail memory =
258686976 (252624K bytes) Programming 24 pins in IOAPIC #0 IOAPIC #0 intpin 2 -> irq 0 FreeBSD/SMP: Multiprocessor motherboard cpu0 (BSP): apic id: 0, version:
0x00040011, at 0xfee00000 cpu1 (AP): apic id: 1, version: 0x00040011, at 0xfee00000 io0 (APIC): apic id: 2, version:
0x00170011, at 0xfec00000 Preloaded elf kernel
"kernel" at 0xc029e000. Pentium Pro MTRR support enabled md0: Malloc disk Using $PIR table, 8 entries at 0xc00fd7e0 npx0: <math processor> on motherboard npx0: INT 16 interface pcib0: <Intel 82443BX (440 BX) host to PCI bridge> on
motherboard IOAPIC #0 intpin 19 -> irq 2 IOAPIC #0 intpin 16 -> irq 10 IOAPIC #0 intpin 18 -> irq 11 pci0: <PCI bus> on pcib0 pcib1: <Intel 82443BX (440 BX) PCI-PCI (AGP) bridge>
at device 1.0 on pci0 pci1: <PCI bus> on pcib1 isab0: <Intel 82371AB PCI to ISA bridge> at device 7.0
on pci0 isa0: <ISA bus> on isab0 atapci0: <Intel PIIX4 ATA33 controller> port
0xf000-0xf00f at device 7.1 on pci0 ata0: at 0x1f0 irq 14 on atapci0 ata1: at 0x170 irq 15 on atapci0 pci0: <Intel 82371AB/EB (PIIX4) USB controller> at 7.2
irq 2 Timecounter "PIIX" frequency
3579545 Hz chip1: <Intel 82371AB Power management controller>
port 0x5000-0x500f at device 7.3 on pci0 pci0: <Matrox MGA Millennium
2064W graphics accelerator> at 15.0 irq 10 rl0: <Accton MPX 5030/5038
10/100BaseTX> port 0xd400-0xd4ff mem 0xd7000000-0xd70000ff irq 2 at
device 17.0 on pci0 rl0: Ethernet address: 00:e0:29:5f:b1:14 miibus0: <MII bus> on rl0 rlphy0: <RealTek internal media
interface> on miibus0 rlphy0: 10baseT,
10baseT-FDX, 100baseTX, 100baseTX-FDX, auto atapci1: <HighPoint HPT366
ATA66 controller> port 0xe000-0xe0ff,0xdc00-0xdc03,0xd800-0xd807
irq 11 at device 19.0 on pci0 ata2: at 0xd800 on atapci1 atapci2: <HighPoint HPT366
ATA66 controller> port 0xec00-0xecff,0xe800-0xe803,0xe400-0xe407
irq 11 at device 19.1 on pci0 ata3: at 0xe400 on atapci2 orm0: <Option ROMs> at iomem 0xc0000-0xc7fff,0xc8000-0xc97ff,0xef000-0xeffff
on isa0 atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 atkbd0: <AT Keyboard> flags 0x1 irq
1 on atkbdc0 kbd0 at atkbd0 vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sio0 at port
0x3f8-0x3ff irq 4 flags 0x10 on isa0 sio0: type 16550A APIC_IO: Testing 8254 interrupt delivery APIC_IO: routing 8254 via IOAPIC #0 intpin
2 IP packet filtering initialized, divert enabled, rule-based
forwarding disabled, default to
deny, logging limited to 200 packets/entry by default SMP: AP CPU #1 Launched! ad6: 57259MB <MAXTOR 4K060H3> [116336/16/63] at
ata3-master UDMA66 Mounting root from ufs:/dev/ad6s1a rl0: promiscuous mode enabled |
