I have been getting unexplicable freezes on my SMP server machine.
It is an Abit VP6 with 1G Micron memory and 2 Intel P3/800 cpus.
It runs fine with a RELENG_4_3 kernel.
It runs fine with a non smp 4.4 RC kernel.
It freezes after some time with a 4.4 RC smp kernel but apparently only
when I start up an X server on my workstation (other machine) and some
x-clients on the smp machine.
The workstation is running 4.4 RC (non smp).
My homedir is on the smp machine, mounted over NFS on the workstation and I
am using NIS and I'm running i4b.
Attached is various dmesg output and the kernel config.
Jos
Copyright (c) 1992-2001 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.4-RC #0: Tue Aug 28 00:03:29 CEST 2001
[EMAIL PROTECTED]:/a/vol/obj/a/vol/src/FreeBSD-4-STABLE/src/sys/islay
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium III/Pentium III Xeon/Celeron (798.69-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x686 Stepping = 6
Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory = 1073676288 (1048512K bytes)
avail memory = 1040818176 (1016424K bytes)
Programming 24 pins in IOAPIC #0
IOAPIC #0 intpin 2 -> irq 0
FreeBSD/SMP: Multiprocessor motherboard
cpu0 (BSP): apic id: 0, version: 0x00040011, at 0xfee00000
cpu1 (AP): apic id: 1, version: 0x00040011, at 0xfee00000
io0 (APIC): apic id: 2, version: 0x00178011, at 0xfec00000
Preloaded elf kernel "kernel-4.4.smp" at 0xc04a7000.
Pentium Pro MTRR support enabled
md0: Malloc disk
Using $PIR table, 8 entries at 0xc00fdc60
apm0: <APM BIOS> on motherboard
apm: found APM BIOS v1.2, connected at v1.2
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
pcib1: <VIA 82C598MVP (Apollo MVP3) PCI-PCI (AGP) bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
isab0: <VIA 82C686 PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <VIA 82C686 ATA100 controller> port 0x9000-0x900f at device 7.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
uhci0: <VIA 83C572 USB controller> port 0x9400-0x941f irq 5 at device 7.2 on pci0
usb0: <VIA 83C572 USB controller> on uhci0
usb0: USB revision 1.0
uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <VIA 83C572 USB controller> port 0x9800-0x981f irq 5 at device 7.3 on pci0
usb1: <VIA 83C572 USB controller> on uhci1
usb1: USB revision 1.0
uhub1: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
chip1: <VIA 82C686 ACPI interface> at device 7.4 on pci0
ahc0: <Adaptec 29160 Ultra160 SCSI adapter> port 0x9c00-0x9cff mem
0xd6100000-0xd6100fff irq 11 at device 9.0 on pci0
aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/255 SCBs
fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0xa000-0xa01f mem
0xd6000000-0xd60fffff,0xd6101000-0xd6101fff irq 12 at device 10.0 on pci0
fxp0: Ethernet address 00:a0:c9:a5:38:7d
inphy0: <i82555 10/100 media interface> on miibus0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pcm0: <Creative CT5880-C> port 0xa400-0xa43f irq 12 at device 11.0 on pci0
pci0: <ATI Mach64-GV graphics accelerator> at 12.0 irq 5
ifpi0: <AVM Fritz!Card PCI> port 0xac00-0xac1f mem 0xd6103000-0xd610301f irq 10 at
device 13.0 on pci0
ifpi0: ISAC 2085 Version A1/A2 or 2086/2186 Version 1.1 (IOM-2)
ifpi0: passive stack unit 0
atapci1: <HighPoint HPT370 ATA100 controller> port
0xc000-0xc0ff,0xbc00-0xbc03,0xb800-0xb807,0xb400-0xb403,0xb000-0xb007 irq 10 at device
14.0 on pci0
ata2: at 0xb000 on atapci1
ata3: at 0xb800 on atapci1
orm0: <Option ROMs> at iomem 0xc0000-0xc7fff,0xc8000-0xcb7ff on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> on isa0
sc0: VGA <16 virtual consoles, flags=0x200>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
ppbus0: IEEE1284 device found /NIBBLE/ECP
Probing for PnP devices on ppbus0:
ppbus0: <Hewlett-Packard HP LaserJet 2100 Series> PJL,MLC,PCL,PCLXL,POSTSCRIPT
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
pcfclock0: <PCF-1.0> on ppbus0
unknown: <PNP0303> can't assign resources
unknown: <PNP0700> can't assign resources
unknown: <PNP0501> can't assign resources
unknown: <PNP0501> can't assign resources
unknown: <PNP0400> can't assign resources
i4bipr: 4 IP over raw HDLC ISDN device(s) attached (VJ header compression)
DUMMYNET initialized (010124)
i4bctl: ISDN system control port attached
i4btrc: 4 ISDN trace device(s) attached
IP packet filtering initialized, divert enabled, rule-based forwarding enabled,
default to accept, unlimited logging
IPv6 packet filtering initialized, default to accept, unlimited logging
i4bisppp: 32 ISDN SyncPPP device(s) attached (VJ header compression)
i4b: ISDN call control device attached
i4btel: 2 ISDN telephony interface device(s) attached
i4brbch: 4 raw B channel access device(s) attached
IPsec: Initialized Security Association Processing.
IP Filter: v3.4.20 initialized. Default = pass all, Logging = enabled
SMP: AP CPU #1 Launched!
ad4: 29314MB <IBM-DTLA-307030> [59560/16/63] at ata2-master tagged UDMA100
ad5: 29314MB <IBM-DTLA-307030> [59560/16/63] at ata2-slave tagged UDMA100
ad6: 19574MB <IBM-DPTA-372050> [39770/16/63] at ata3-master tagged UDMA66
ad7: 19574MB <IBM-DPTA-372050> [39770/16/63] at ata3-slave tagged UDMA66
Waiting 3 seconds for SCSI devices to settle
sa0 at ahc0 bus 0 target 4 lun 0
sa0: <HP HP35470A 1009> Removable Sequential Access SCSI-2 device
sa0: 5.000MB/s transfers (5.000MHz, offset 8)
Mounting root from ufs:/dev/ad4s1a
cd0 at ahc0 bus 0 target 0 lun 0
cd0: <TOSHIBA CD-ROM XM-5301TA 1895> Removable CD-ROM SCSI-2 device
cd0: 3.300MB/s transfers
cd0: Attempt to query device size failed: NOT READY, Medium not present
da0 at ahc0 bus 0 target 1 lun 0
da0: <IBM DNES-309170W SAH0> Fixed Direct Access SCSI-3 device
da0: 80.000MB/s transfers (40.000MHz, offset 30, 16bit), Tagged Queueing Enabled
da0: 8748MB (17916240 512 byte sectors: 255H 63S/T 1115C)
Copyright (c) 1992-2001 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.4-RC #0: Tue Aug 28 00:22:37 CEST 2001
[EMAIL PROTECTED]:/a/vol/obj/a/vol/src/FreeBSD-4-STABLE/src/sys/islay-nosmp
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium III/Pentium III Xeon/Celeron (798.69-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x686 Stepping = 6
Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory = 1073676288 (1048512K bytes)
avail memory = 1040900096 (1016504K bytes)
Preloaded elf kernel "kernel-4.4.nosmp" at 0xc0496000.
Pentium Pro MTRR support enabled
md0: Malloc disk
Using $PIR table, 8 entries at 0xc00fdc60
apm0: <APM BIOS> on motherboard
apm: found APM BIOS v1.2, connected at v1.2
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
pcib1: <VIA 82C598MVP (Apollo MVP3) PCI-PCI (AGP) bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
isab0: <VIA 82C686 PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <VIA 82C686 ATA100 controller> port 0x9000-0x900f at device 7.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
uhci0: <VIA 83C572 USB controller> port 0x9400-0x941f irq 5 at device 7.2 on pci0
usb0: <VIA 83C572 USB controller> on uhci0
usb0: USB revision 1.0
uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <VIA 83C572 USB controller> port 0x9800-0x981f irq 5 at device 7.3 on pci0
usb1: <VIA 83C572 USB controller> on uhci1
usb1: USB revision 1.0
uhub1: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
chip1: <VIA 82C686 ACPI interface> at device 7.4 on pci0
ahc0: <Adaptec 29160 Ultra160 SCSI adapter> port 0x9c00-0x9cff mem
0xd6100000-0xd6100fff irq 11 at device 9.0 on pci0
aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/255 SCBs
fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0xa000-0xa01f mem
0xd6000000-0xd60fffff,0xd6101000-0xd6101fff irq 12 at device 10.0 on pci0
fxp0: Ethernet address 00:a0:c9:a5:38:7d
inphy0: <i82555 10/100 media interface> on miibus0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pcm0: <Creative CT5880-C> port 0xa400-0xa43f irq 12 at device 11.0 on pci0
pci0: <ATI Mach64-GV graphics accelerator> at 12.0 irq 5
ifpi0: <AVM Fritz!Card PCI> port 0xac00-0xac1f mem 0xd6103000-0xd610301f irq 10 at
device 13.0 on pci0
ifpi0: ISAC 2085 Version A1/A2 or 2086/2186 Version 1.1 (IOM-2)
ifpi0: passive stack unit 0
atapci1: <HighPoint HPT370 ATA100 controller> port
0xc000-0xc0ff,0xbc00-0xbc03,0xb800-0xb807,0xb400-0xb403,0xb000-0xb007 irq 10 at device
14.0 on pci0
ata2: at 0xb000 on atapci1
ata3: at 0xb800 on atapci1
orm0: <Option ROMs> at iomem 0xc0000-0xc7fff,0xc8000-0xcb7ff on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> on isa0
sc0: VGA <16 virtual consoles, flags=0x200>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
ppbus0: IEEE1284 device found /NIBBLE/ECP
Probing for PnP devices on ppbus0:
ppbus0: <Hewlett-Packard HP LaserJet 2100 Series> PJL,MLC,PCL,PCLXL,POSTSCRIPT
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
pcfclock0: <PCF-1.0> on ppbus0
unknown: <PNP0000> can't assign resources
unknown: <PNP0303> can't assign resources
unknown: <PNP0700> can't assign resources
unknown: <PNP0501> can't assign resources
unknown: <PNP0501> can't assign resources
unknown: <PNP0400> can't assign resources
i4brbch: 4 raw B channel access device(s) attached
i4bipr: 4 IP over raw HDLC ISDN device(s) attached (VJ header compression)
DUMMYNET initialized (010124)
i4bctl: ISDN system control port attached
i4btrc: 4 ISDN trace device(s) attached
IP packet filtering initialized, divert enabled, rule-based forwarding enabled,
default to accept, unlimited logging
IPv6 packet filtering initialized, default to accept, unlimited logging
i4bisppp: 32 ISDN SyncPPP device(s) attached (VJ header compression)
i4b: ISDN call control device attached
i4btel: 2 ISDN telephony interface device(s) attached
IPsec: Initialized Security Association Processing.
IP Filter: v3.4.20 initialized. Default = pass all, Logging = enabled
ad4: 29314MB <IBM-DTLA-307030> [59560/16/63] at ata2-master tagged UDMA100
ad5: 29314MB <IBM-DTLA-307030> [59560/16/63] at ata2-slave tagged UDMA100
ad6: 19574MB <IBM-DPTA-372050> [39770/16/63] at ata3-master tagged UDMA66
ad7: 19574MB <IBM-DPTA-372050> [39770/16/63] at ata3-slave tagged UDMA66
Waiting 3 seconds for SCSI devices to settle
sa0 at ahc0 bus 0 target 4 lun 0
sa0: <HP HP35470A 1009> Removable Sequential Access SCSI-2 device
sa0: 5.000MB/s transfers (5.000MHz, offset 8)
Mounting root from ufs:/dev/ad4s1a
cd0 at ahc0 bus 0 target 0 lun 0
cd0: <TOSHIBA CD-ROM XM-5301TA 1895> Removable CD-ROM SCSI-2 device
cd0: 3.300MB/s transfers
cd0: Attempt to query device size failed: NOT READY, Medium not present
da0 at ahc0 bus 0 target 1 lun 0
da0: <IBM DNES-309170W SAH0> Fixed Direct Access SCSI-3 device
da0: 80.000MB/s transfers (40.000MHz, offset 30, 16bit), Tagged Queueing Enabled
da0: 8748MB (17916240 512 byte sectors: 255H 63S/T 1115C)
Copyright (c) 1992-2001 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.3-RELEASE-p12 #0: Sat Aug 18 11:31:50 CEST 2001
[EMAIL PROTECTED]:/a/vol/src/FreeBSD-4.3/src/sys/compile/islay
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium III/Pentium III Xeon/Celeron (798.69-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x686 Stepping = 6
Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory = 1073676288 (1048512K bytes)
avail memory = 1040896000 (1016500K bytes)
Programming 24 pins in IOAPIC #0
IOAPIC #0 intpin 2 -> irq 0
FreeBSD/SMP: Multiprocessor motherboard
cpu0 (BSP): apic id: 0, version: 0x00040011, at 0xfee00000
cpu1 (AP): apic id: 1, version: 0x00040011, at 0xfee00000
io0 (APIC): apic id: 2, version: 0x00178011, at 0xfec00000
Preloaded elf kernel "kernel-4.3" at 0xc0493000.
Pentium Pro MTRR support enabled
ERROR: "i4bctl" bmaj but is not a disk
ERROR: "i4btel" bmaj but is not a disk
ERROR: "i4brbch" bmaj but is not a disk
ERROR: "i4btrc" bmaj but is not a disk
ERROR: "i4b" bmaj but is not a disk
md0: Malloc disk
apm0: <APM BIOS> on motherboard
apm: found APM BIOS v1.2, connected at v1.2
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
pcib1: <VIA 82C598MVP (Apollo MVP3) PCI-PCI (AGP) bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
isab0: <VIA 82C686 PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <VIA 82C686 ATA100 controller> port 0x9000-0x900f at device 7.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
uhci0: <VIA 83C572 USB controller> port 0x9400-0x941f irq 5 at device 7.2 on pci0
usb0: <VIA 83C572 USB controller> on uhci0
usb0: USB revision 1.0
uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <VIA 83C572 USB controller> port 0x9800-0x981f irq 5 at device 7.3 on pci0
usb1: <VIA 83C572 USB controller> on uhci1
usb1: USB revision 1.0
uhub1: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
chip1: <VIA 82C686 ACPI interface> at device 7.4 on pci0
ahc0: <Adaptec 29160 Ultra160 SCSI adapter> port 0x9c00-0x9cff mem
0xd6100000-0xd6100fff irq 11 at device 9.0 on pci0
aic7892: Wide Channel A, SCSI Id=7, 32/255 SCBs
fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0xa000-0xa01f mem
0xd6000000-0xd60fffff,0xd6101000-0xd6101fff irq 12 at device 10.0 on pci0
fxp0: Ethernet address 00:a0:c9:a5:38:7d
pcm0: <AudioPCI ES1371> port 0xa400-0xa43f irq 12 at device 11.0 on pci0
pci0: <ATI Mach64-GV graphics accelerator> at 12.0 irq 5
ifpi0: <AVM Fritz!Card PCI> port 0xac00-0xac1f mem 0xd6103000-0xd610301f irq 10 at
device 13.0 on pci0
ifpi0: ISAC 2085 Version A1/A2 or 2086/2186 Version 1.1 (IOM-2)
ifpi0: passive stack unit 0
atapci1: <HighPoint HPT370 ATA100 controller> port
0xc000-0xc0ff,0xbc00-0xbc03,0xb800-0xb807,0xb400-0xb403,0xb000-0xb007 irq 10 at device
14.0 on pci0
ata2: at 0xb000 on atapci1
ata3: at 0xb800 on atapci1
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> on isa0
sc0: VGA <16 virtual consoles, flags=0x200>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
ppbus0: IEEE1284 device found /NIBBLE/ECP
Probing for PnP devices on ppbus0:
ppbus0: <Hewlett-Packard HP LaserJet 2100 Series> PJL,MLC,PCL,PCLXL,POSTSCRIPT
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
pcfclock0: <PCF-1.0> on ppbus0
unknown: <PNP0303> can't assign resources
unknown: <PNP0700> can't assign resources
unknown: <PNP0501> can't assign resources
unknown: <PNP0501> can't assign resources
unknown: <PNP0400> can't assign resources
IPv6 packet filtering initialized, default to accept, unlimited logging
i4btrc: 4 ISDN trace device(s) attached
i4bisppp: 32 ISDN SyncPPP device(s) attached (VJ header compression)
i4b: ISDN call control device attached
i4btel: 2 ISDN telephony interface device(s) attached
DUMMYNET initialized (010124)
i4brbch: 4 raw B channel access device(s) attached
i4bipr: 4 IP over raw HDLC ISDN device(s) attached (VJ header compression)
IP packet filtering initialized, divert enabled, rule-based forwarding enabled,
default to accept, unlimited logging
i4bctl: ISDN system control port attached
IPsec: Initialized Security Association Processing.
IP Filter: v3.4.16 initialized. Default = pass all, Logging = enabled
SMP: AP CPU #1 Launched!
ad4: 29314MB <IBM-DTLA-307030> [59560/16/63] at ata2-master tagged UDMA100
ad5: 29314MB <IBM-DTLA-307030> [59560/16/63] at ata2-slave tagged UDMA100
ad6: 19574MB <IBM-DPTA-372050> [39770/16/63] at ata3-master tagged UDMA66
ad7: 19574MB <IBM-DPTA-372050> [39770/16/63] at ata3-slave tagged UDMA66
Waiting 3 seconds for SCSI devices to settle
sa0 at ahc0 bus 0 target 4 lun 0
sa0: <HP HP35470A 1009> Removable Sequential Access SCSI-2 device
sa0: 5.000MB/s transfers (5.000MHz, offset 8)
Mounting root from ufs:/dev/ad4s1a
cd0 at ahc0 bus 0 target 0 lun 0
cd0: <TOSHIBA CD-ROM XM-5301TA 1895> Removable CD-ROM SCSI-2 device
cd0: 3.300MB/s transfers
cd0: Attempt to query device size failed: NOT READY, Medium not present
da0 at ahc0 bus 0 target 1 lun 0
da0: <IBM DNES-309170W SAH0> Fixed Direct Access SCSI-3 device
da0: 80.000MB/s transfers (40.000MHz, offset 30, 16bit), Tagged Queueing Enabled
da0: 8748MB (17916240 512 byte sectors: 255H 63S/T 1115C)
machine i386
cpu I686_CPU
ident islay
maxusers 128
#makeoptions DEBUG=-g #Build kernel with gdb(1) debug symbols
options INET #InterNETworking
options INET6 #IPv6 communications protocols
options IPSEC #IP security
options IPSEC_ESP #IP security (crypto; define w/ IPSEC)
#options IPSEC_DEBUG #debug for IP security
options FFS #Berkeley Fast Filesystem
options FFS_ROOT #FFS usable as root device [keep this!]
#options MFS #Memory Filesystem
#options MD_ROOT #MD is a potential root device
options NFS #Network Filesystem
#options NFS_ROOT #NFS usable as root device, NFS required
#options MSDOSFS #MSDOS Filesystem
#options CD9660 #ISO 9660 Filesystem
#options CD9660_ROOT #CD-ROM usable as root, CD9660 required
options PROCFS #Process filesystem
options COMPAT_43 #Compatible with BSD 4.3 [KEEP THIS!]
options SCSI_DELAY=3000 #Delay (in ms) before probing SCSI
options UCONSOLE #Allow users to grab the console
options USERCONFIG #boot -c editor
options VISUAL_USERCONFIG #visual boot -c editor
options KTRACE #ktrace(1) support
options USER_LDT #allow user-level control of i386 ldt
options SYSVSHM #SYSV-style shared memory
options SYSVMSG #SYSV-style message queues
options SYSVSEM #SYSV-style semaphores
options P1003_1B #Posix P1003_1B real-time extentions
options _KPOSIX_PRIORITY_SCHEDULING
options IPFIREWALL #firewall
options IPFIREWALL_VERBOSE #print information about
options IPFIREWALL_FORWARD #enable transparent proxy support
options IPFIREWALL_DEFAULT_TO_ACCEPT #allow everything by default
options IPDIVERT #divert sockets
options DUMMYNET # the "dummynet" bandwidth limiter
options IPV6FIREWALL #firewall for IPv6
options IPV6FIREWALL_VERBOSE #print information about
options IPV6FIREWALL_DEFAULT_TO_ACCEPT
options IPFILTER #ipfilter support
options IPFILTER_LOG #ipfilter logging
#options IPFILTER_DEFAULT_BLOCK #block all packets by default
options TCP_DROP_SYNFIN #drop TCP packets with SYN+FIN
options ICMP_BANDLIM #Rate limit bad replies
#options NETGRAPH #netgraph(4) system
options SOFTUPDATES
options PNPBIOS
options NMBCLUSTERS=4096
options MAXDSIZ="(256*1024*1024)"
options DFLDSIZ="(256*1024*1024)"
#options I4B_SMP_WORKAROUND # only required for isic? (Teles 16.3)
# To make an SMP kernel, the next two are needed
options SMP # Symmetric MultiProcessor Kernel
options APIC_IO # Symmetric (APIC) I/O
device isa
device pci
# Floppy drives
device fdc0 at isa? port IO_FD1 irq 6 drq 2
device fd0 at fdc0 drive 0
device fd1 at fdc0 drive 1
# ATA and ATAPI devices
device ata
device atadisk # ATA disk drives
#device atapicd # ATAPI CDROM drives
#device atapifd # ATAPI floppy drives
#device atapist # ATAPI tape drives
options ATA_STATIC_ID #Static device numbering
# SCSI Controllers
#device ahb # EISA AHA1742 family
device ahc # AHA2940 and onboard AIC7xxx devices
device amd # AMD 53C974 (Teckram DC-390(T))
#device dpt # DPT Smartcache - See LINT for options!
#device isp # Qlogic family
#device ncr # NCR/Symbios Logic
#device sym # NCR/Symbios Logic (newer chipsets)
#device adv0 at isa?
#device adw
#device bt0 at isa?
#device aha0 at isa?
#device aic0 at isa?
# SCSI peripherals
device scbus # SCSI bus (required)
device da # Direct Access (disks)
device sa # Sequential Access (tape etc)
device cd # CD
device pass # Passthrough device (direct SCSI access)
# RAID controllers
#device ida # Compaq Smart RAID
#device amr # AMI MegaRAID
#device mlx # Mylex DAC960 family
# atkbdc0 controls both the keyboard and the PS/2 mouse
device atkbdc0 at isa? port IO_KBD
device atkbd0 at atkbdc? irq 1
device psm0 at atkbdc? irq 12
device vga0 at isa?
# splash screen/screen saver
pseudo-device splash
# syscons is the default console driver, resembling an SCO console
device sc0 at isa?
# Enable this and PCVT_FREEBSD for pcvt vt220 compatible console driver
#device vt0 at isa?
options XSERVER # support for X server on a vt console
#options FAT_CURSOR # start with block cursor
# If you have a ThinkPAD, uncomment this along with the rest of the PCVT lines
#options PCVT_SCANSET=2 # IBM keyboards are non-std
# Floating point support - do not disable.
device npx0 at nexus? port IO_NPX irq 13
# Power management support (see LINT for more options)
device apm0 at nexus? flags 0x20 # Advanced Power Management
# Serial (COM) ports
device sio0 at isa? port IO_COM1 flags 0x10 irq 4
device sio1 at isa? port IO_COM2 irq 3
device sio2 at isa? disable port IO_COM3 irq 5
device sio3 at isa? disable port IO_COM4 irq 9
# Parallel port
device ppc0 at isa? irq 7
device ppbus # Parallel port bus (required)
device lpt # Printer
#device plip # TCP/IP over parallel
#device ppi # Parallel port interface device
#device vpo # Requires scbus and da
#device pps # Pulse per second Timing Interface
device lpbb # Philips official parallel port I2C
# bit-banging interface
#options PCFCLOCK_VERBOSE # Verbose pcfclock driver
#options PCFCLOCK_MAX_RETRIES=5 # Maximum read tries (default 10)
device pcfclock
# PCI Ethernet NICs.
#device de # DEC/Intel DC21x4x (``Tulip'')
device fxp # Intel EtherExpress PRO/100B (82557, 82558)
#device tx # SMC 9432TX (83c170 ``EPIC'')
device vx # 3Com 3c590, 3c595 (``Vortex'')
#device wx # Intel Gigabit Ethernet Card (``Wiseman'')
# PCI Ethernet NICs that use the common MII bus controller code.
device miibus # MII bus support
#device dc # DEC/Intel 21143 and various workalikes
#device rl # RealTek 8129/8139
#device sf # Adaptec AIC-6915 (``Starfire'')
#device sis # Silicon Integrated Systems SiS 900/SiS 7016
#device ste # Sundance ST201 (D-Link DFE-550TX)
#device tl # Texas Instruments ThunderLAN
#device vr # VIA Rhine, Rhine II
#device wb # Winbond W89C840F
#device xl # 3Com 3c90x (``Boomerang'', ``Cyclone'')
# ISA Ethernet NICs.
#device ed0 at isa? port 0x280 irq 10 iomem 0xd8000
device ed0
#device ex
#device ep
# Aironet 4500/4800 802.11 wireless NICs. Note: the declaration below will
# work for PCMCIA and PCI cards, as well as ISA cards set to ISA PnP
# mode (the factory default). If you set the switches on your ISA
# card for a manually chosen I/O address and IRQ, you must specify
# those paremeters here.
#device an
# The probe order of these is presently determined by i386/isa/isa_compat.c.
#device ie0 at isa? port 0x300 irq 10 iomem 0xd0000
#device fe0 at isa? port 0x300
#device le0 at isa? port 0x300 irq 5 iomem 0xd0000
#device lnc0 at isa? port 0x280 irq 10 drq 0
#device cs0 at isa? port 0x300
#device sn0 at isa? port 0x300 irq 10
# Pseudo devices - the number indicates how many units to allocated.
pseudo-device loop # Network loopback
pseudo-device ether # Ethernet support
#pseudo-device sl 1 # Kernel SLIP
pseudo-device ppp 1 # Kernel PPP
options PPP_BSDCOMP #PPP BSD-compress support
options PPP_DEFLATE #PPP zlib/deflate/gzip support
options PPP_FILTER #enable bpf filtering (needs bpf)
pseudo-device tun # Packet tunnel.
pseudo-device pty # Pseudo-ttys (telnet etc)
pseudo-device md # Memory "disks"
pseudo-device gif # IPv6 and IPv4 tunneling
pseudo-device faith 1 # IPv6-to-IPv4 relaying (translation)
pseudo-device vn #Vnode driver (turns a file into a device)
pseudo-device snp 3 #Snoop device - to look at pty/vty/etc..
# The `bpf' pseudo-device enables the Berkeley Packet Filter.
# Be aware of the administrative consequences of enabling this!
pseudo-device bpf #Berkeley packet filter
# USB support
device uhci # UHCI PCI->USB interface
device ohci # OHCI PCI->USB interface
device usb # USB Bus (required)
device ugen # Generic
device uhid # "Human Interface Devices"
device ukbd # Keyboard
device ulpt # Printer
device umass # Disks/Mass storage - Requires scbus and da
device ums # Mouse
# USB Ethernet, requires mii
#device aue # ADMtek USB ethernet
#device cue # CATC USB ethernet
#device kue # Kawasaki LSI USB ethernet
#
# debugging options for the USB subsystem
#options UHCI_DEBUG
#options OHCI_DEBUG
#options USB_DEBUG
#options UGEN_DEBUG
#options UHID_DEBUG
#options UHUB_DEBUG
#options UKBD_DEBUG
#options ULPT_DEBUG
#options UMASS_DEBUG
#options UMS_DEBUG
# Sound:
device pcm
# System Management Bus:
device smbus # Bus support, required for smb
device iicbus # Bus support, required for ic/iic/iicsmb
device iicbb # generic I2C bit-banging code
device alpm # Acer Aladdin-IV/V/Pro2 Power Management Unit
device intpm # Intel PIIX4 Power Management Unit
device bktr # brooktree848 I2C software interface
# ISDN4BSD section
#
# last edit-date: [Sun Jul 22 17:35:36 2001]
#
#---------------------------------------------------------------------------
# Siemens/Infineon chipsets
#device isic0
# Winbond chipset
#device iwic0
# AVM Fritz PCI
device ifpi0
# Teles 16.3c
#device ihfc0
# NETjet-S / Teles PCI-TJ
#device itjc0
# AVM Fritz PnP
#device ifpnp0
# AVM B1/T1
#device "i4bcapi"
#device iavc0
# enable some ISA cards within the "isic" driver
#options TEL_S0_8
#options TEL_S0_16
#options TEL_S0_16_3
#options AVM_A1
#options USR_STI
#options ELSA_PCC16
# enable some ISA PnP cards within the "isic" driver
#options TEL_S0_16_3_P
#options CRTX_S0_P
#options DRN_NGO
#options SEDLBAUER
#options ELSA_QS1ISA
#options SIEMENS_ISURF2
#options ASUSCOM_IPAC
#options EICON_DIVA
# enable ELSA Microlink PCI card within the "isic" driver
#options ELSA_QS1PCI
# protocol stack
pseudo-device "i4bq921"
pseudo-device "i4bq931"
pseudo-device "i4b"
# control devices
pseudo-device "i4btrc" 4
pseudo-device "i4bctl"
pseudo-device "i4brbch" 4
pseudo-device "i4btel" 2
# IP over raw HDLC
options IPR_VJ
pseudo-device "i4bipr" 4
# kernel sppp/isppp
pseudo-device "i4bisppp" 32
# Netgraph interface (does not compile on 4.x !)
#options NETGRAPH
#pseudo-device "i4bing" 4
