Seems to be related to be related to your SSD drive or the SATA control. do you a secondary SSD or HDD to try on this machine? I've seen this happen on my Intel SSD in the past.
Thx . On Wed, Aug 19, 2015 at 8:07 AM, Gerhard Schmidt <esta...@ze.tum.de> wrote: > Hi, > > I'm trying to install FreeBSD 10.2 on a MacPro. > > Installing and Booting works. But a few seconds after login and accessing > the Harddisk, I'm getting the following errors. > ahcich0: Timeout on slot 13 port 0 > ahcich0: is 00000008 cs 00000000 ss 00000000 rs ffffffff tfd 40 serr > 00000000 cmd 0000cd17 > (ada0:ahcich0:0:0:0): WRITE_FPDMA_QUEUED. ACB: 61 00 28 15 40 40 2f 00 00 > 01 00 00 > (ada0:ahcich0:0:0:0): CAM status: Command timeout > (ada0:ahcich0:0:0:0): Retrying command > ahcich0: Timeout on slot 15 port 0 > ahcich0: is 00000008 cs 00000000 ss 00000000 rs ffffffff tfd 40 serr > 00000000 cmd 0000cf17 > (ada0:ahcich0:0:0:0): WRITE_FPDMA_QUEUED. ACB: 61 08 a0 5f bd 40 13 00 00 > 00 00 00 > (ada0:ahcich0:0:0:0): CAM status: Command timeout > (ada0:ahcich0:0:0:0): Retrying command > ahcich0: Timeout on slot 2 port 0 > ahcich0: is 00000008 cs 00000000 ss 00000000 rs ffffffff tfd 40 serr > 00000000 cmd 0000c217 > (ada0:ahcich0:0:0:0): WRITE_FPDMA_QUEUED. ACB: 61 08 c0 23 bd 40 13 00 00 > 00 00 00 > (ada0:ahcich0:0:0:0): CAM status: Command timeout > (ada0:ahcich0:0:0:0): Retrying command > > Any Ideas what causes this and what can be done to fix it. > > the dmesg of the MacPro is the following > > Copyright (c) 1992-2015 The FreeBSD Project. > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > The Regents of the University of California. All rights reserved. > FreeBSD is a registered trademark of The FreeBSD Foundation. > FreeBSD 10.2-RELEASE #0 r286666: Wed Aug 12 15:26:37 UTC 2015 > r...@releng1.nyi.freebsd.org:/usr/obj/usr/src/sys/GENERIC amd64 > FreeBSD clang version 3.4.1 (tags/RELEASE_34/dot1-final 208032) 20140512 > VT: running with driver "efifb". > CPU: Intel(R) Xeon(R) CPU E5-2697 v2 @ 2.70GHz (2700.06-MHz K8-class CPU) > Origin="GenuineIntel" Id=0x306e4 Family=0x6 Model=0x3e Stepping=4 > > > Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> > > > Features2=0x7fbee3ff<SSE3,PCLMULQDQ,DTES64,MON,DS_CPL,VMX,SMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,PCID,DCA,SSE4.1,SSE4.2,x2APIC,POPCNT,TSCDLT,AESNI,XSAVE,OSXSAVE,AVX,F16C,RDRAND> > AMD Features=0x2c100800<SYSCALL,NX,Page1GB,RDTSCP,LM> > AMD Features2=0x1<LAHF> > Structured Extended Features=0x281<FSGSBASE,SMEP,ERMS> > XSAVE Features=0x1<XSAVEOPT> > VT-x: PAT,HLT,MTF,PAUSE,EPT,UG,VPID,VID,PostIntr > TSC: P-state invariant, performance statistics > real memory = 68719476736 (65536 MB) > avail memory = 66655334400 (63567 MB) > Event timer "LAPIC" quality 600 > ACPI APIC Table: <APPLE Apple00> > FreeBSD/SMP: Multiprocessor System Detected: 24 CPUs > FreeBSD/SMP: 1 package(s) x 12 core(s) x 2 SMT threads > cpu0 (BSP): APIC ID: 0 > cpu1 (AP): APIC ID: 1 > cpu2 (AP): APIC ID: 2 > cpu3 (AP): APIC ID: 3 > cpu4 (AP): APIC ID: 4 > cpu5 (AP): APIC ID: 5 > cpu6 (AP): APIC ID: 6 > cpu7 (AP): APIC ID: 7 > cpu8 (AP): APIC ID: 8 > cpu9 (AP): APIC ID: 9 > cpu10 (AP): APIC ID: 10 > cpu11 (AP): APIC ID: 11 > cpu12 (AP): APIC ID: 16 > cpu13 (AP): APIC ID: 17 > cpu14 (AP): APIC ID: 18 > cpu15 (AP): APIC ID: 19 > cpu16 (AP): APIC ID: 20 > cpu17 (AP): APIC ID: 21 > cpu18 (AP): APIC ID: 22 > cpu19 (AP): APIC ID: 23 > cpu20 (AP): APIC ID: 24 > cpu21 (AP): APIC ID: 25 > cpu22 (AP): APIC ID: 26 > cpu23 (AP): APIC ID: 27 > ioapic0 <Version 2.0> irqs 0-23 on motherboard > ioapic1 <Version 2.0> irqs 24-47 on motherboard > lapic0: Forcing LINT1 to edge trigger > random: <Software, Yarrow> initialized > module_register_init: MOD_LOAD (vesa, 0xffffffff80db8eb0, 0) error 19 > kbd0 at kbdmux0 > acpi0: <APPLE Apple00> on motherboard > acpi0: Power Button (fixed) > unknown: I/O range not supported > Timecounter "HPET" frequency 14318180 Hz quality 950 > Event timer "HPET" frequency 14318180 Hz quality 350 > Event timer "HPET1" frequency 14318180 Hz quality 340 > Event timer "HPET2" frequency 14318180 Hz quality 340 > Event timer "HPET3" frequency 14318180 Hz quality 340 > Event timer "HPET4" frequency 14318180 Hz quality 340 > Event timer "HPET5" frequency 14318180 Hz quality 340 > Event timer "HPET6" frequency 14318180 Hz quality 340 > Event timer "HPET7" frequency 14318180 Hz quality 340 > cpu0: <ACPI CPU> on acpi0 > cpu1: <ACPI CPU> on acpi0 > cpu2: <ACPI CPU> on acpi0 > cpu3: <ACPI CPU> on acpi0 > cpu4: <ACPI CPU> on acpi0 > cpu5: <ACPI CPU> on acpi0 > cpu6: <ACPI CPU> on acpi0 > cpu7: <ACPI CPU> on acpi0 > cpu8: <ACPI CPU> on acpi0 > cpu9: <ACPI CPU> on acpi0 > cpu10: <ACPI CPU> on acpi0 > cpu11: <ACPI CPU> on acpi0 > cpu12: <ACPI CPU> on acpi0 > cpu13: <ACPI CPU> on acpi0 > cpu14: <ACPI CPU> on acpi0 > cpu15: <ACPI CPU> on acpi0 > cpu16: <ACPI CPU> on acpi0 > cpu17: <ACPI CPU> on acpi0 > cpu18: <ACPI CPU> on acpi0 > cpu19: <ACPI CPU> on acpi0 > cpu20: <ACPI CPU> on acpi0 > cpu21: <ACPI CPU> on acpi0 > cpu22: <ACPI CPU> on acpi0 > cpu23: <ACPI CPU> on acpi0 > atrtc0: <AT realtime clock> port 0x70-0x77 on acpi0 > Event timer "RTC" frequency 32768 Hz quality 0 > attimer0: <AT timer> port 0x40-0x43,0x50-0x53 on acpi0 > Timecounter "i8254" frequency 1193182 Hz quality 0 > Event timer "i8254" frequency 1193182 Hz quality 100 > Timecounter "ACPI-fast" frequency 3579545 Hz quality 900 > acpi_timer0: <24-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0 > acpi_ec0: <Embedded Controller: GPE 0x17> port 0x62,0x66 on acpi0 > pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 > pci0: <ACPI PCI bus> on pcib0 > pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0 > pci16: <ACPI PCI bus> on pcib1 > pcib2: <ACPI PCI-PCI bridge> mem 0xbf900000-0xbf93ffff at device 0.0 on > pci16 > pci17: <ACPI PCI bus> on pcib2 > pcib3: <ACPI PCI-PCI bridge> at device 1.0 on pci17 > pci18: <ACPI PCI bus> on pcib3 > xhci0: <XHCI (generic) USB 3.0 controller> mem > 0xa0900000-0xa090ffff,0xa0910000-0xa0910fff,0xa0911000-0xa0911fff at > device 0.0 on pci18 > xhci0: 32 bytes context size, 64-bit DMA > usbus0 on xhci0 > pcib4: <ACPI PCI-PCI bridge> at device 2.0 on pci17 > pci20: <ACPI PCI bus> on pcib4 > pcib5: <ACPI PCI-PCI bridge> at device 8.0 on pci17 > pci19: <ACPI PCI bus> on pcib5 > pcib6: <ACPI PCI-PCI bridge> at device 9.0 on pci17 > pci91: <ACPI PCI bus> on pcib6 > pcib7: <ACPI PCI-PCI bridge> at device 10.0 on pci17 > pci162: <ACPI PCI bus> on pcib7 > pcib8: <ACPI PCI-PCI bridge> at device 2.0 on pci0 > pci2: <ACPI PCI bus> on pcib8 > vgapci0: <VGA-compatible display> port 0x3000-0x30ff mem > 0x80000000-0x8fffffff,0xa0700000-0xa073ffff at device 0.0 on pci2 > hdac0: <ATI R1000 HDA Controller> mem 0xa0760000-0xa0763fff at device 0.1 > on pci2 > hdac0: hdac_get_capabilities: Invalid corb size (0) > device_attach: hdac0 attach returned 6 > pcib9: <ACPI PCI-PCI bridge> at device 3.0 on pci0 > pci6: <ACPI PCI bus> on pcib9 > vgapci1: <VGA-compatible display> port 0x2000-0x20ff mem > 0x90000000-0x9fffffff,0xa0600000-0xa063ffff at device 0.0 on pci6 > hdac0: <ATI R1000 HDA Controller> mem 0xa0660000-0xa0663fff at device 0.1 > on pci6 > hdac0: hdac_get_capabilities: Invalid corb size (0) > device_attach: hdac0 attach returned 6 > pcib10: <ACPI PCI-PCI bridge> at device 17.0 on pci0 > pci10: <ACPI PCI bus> on pcib10 > pci0: <simple comms> at device 22.0 (no driver attached) > hdac0: <Intel Patsburg HDA Controller> mem 0xa0820000-0xa0823fff at device > 27.0 on pci0 > pcib11: <ACPI PCI-PCI bridge> at device 28.0 on pci0 > pci11: <ACPI PCI bus> on pcib11 > bge0: <Broadcom NetXtreme Gigabit Ethernet Controller, ASIC rev. > 0x57766000> mem > 0xa0300000-0xa030ffff,0xa0310000-0xa031ffff at device 0.0 on pci11 > bge0: CHIP ID 0x57766000; ASIC REV 0x57766; CHIP REV 0x577660; PCI-E > miibus0: <MII bus> on bge0 > brgphy0: <BCM57765 1000BASE-T media interface> PHY 1 on miibus0 > brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, > 1000baseT-master, 1000baseT-FDX, > 1000baseT-FDX-master, auto, auto-flow > bge0: Using defaults for TSO: 65518/35/2048 > bge0: Ethernet address: 00:3e:e1:c2:1a:e3 > pcib12: <ACPI PCI-PCI bridge> at device 28.1 on pci0 > pci12: <ACPI PCI bus> on pcib12 > bge1: <Broadcom NetXtreme Gigabit Ethernet Controller, ASIC rev. > 0x57766000> mem > 0xa0400000-0xa040ffff,0xa0410000-0xa041ffff at device 0.0 on pci12 > bge1: CHIP ID 0x57766000; ASIC REV 0x57766; CHIP REV 0x577660; PCI-E > miibus1: <MII bus> on bge1 > brgphy1: <BCM57765 1000BASE-T media interface> PHY 1 on miibus1 > brgphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, > 1000baseT-master, 1000baseT-FDX, > 1000baseT-FDX-master, auto, auto-flow > bge1: Using defaults for TSO: 65518/35/2048 > bge1: Ethernet address: 00:3e:e1:c2:1a:e2 > pcib13: <ACPI PCI-PCI bridge> at device 28.2 on pci0 > pci13: <ACPI PCI bus> on pcib13 > pci13: <network> at device 0.0 (no driver attached) > pcib14: <ACPI PCI-PCI bridge> at device 28.4 on pci0 > pci14: <ACPI PCI bus> on pcib14 > ahci0: <AHCI SATA controller> mem 0xa0500000-0xa0501fff at device 0.0 on > pci14 > ahci0: AHCI v1.30 with 1 6Gbps ports, Port Multiplier not supported > ahcich0: <AHCI channel> at channel 0 on ahci0 > ehci0: <Intel Patsburg USB 2.0 controller> mem 0xa0827800-0xa0827bff at > device 29.0 on pci0 > usbus1: EHCI version 1.0 > usbus1 on ehci0 > pcib15: <ACPI PCI-PCI bridge> at device 30.0 on pci0 > pci15: <ACPI PCI bus> on pcib15 > isab0: <PCI-ISA bridge> at device 31.0 on pci0 > isa0: <ISA bus> on isab0 > acpi_button0: <Power Button> on acpi0 > acpi_button1: <Sleep Button> on acpi0 > ppc0: cannot reserve I/O port range > uart0: <8250 or 16450 or compatible> at port 0x3f8-0x3ff irq 4 flags 0x10 > on isa0 > est0: <Enhanced SpeedStep Frequency Control> on cpu0 > est1: <Enhanced SpeedStep Frequency Control> on cpu1 > est2: <Enhanced SpeedStep Frequency Control> on cpu2 > est3: <Enhanced SpeedStep Frequency Control> on cpu3 > est4: <Enhanced SpeedStep Frequency Control> on cpu4 > est5: <Enhanced SpeedStep Frequency Control> on cpu5 > est6: <Enhanced SpeedStep Frequency Control> on cpu6 > est7: <Enhanced SpeedStep Frequency Control> on cpu7 > est8: <Enhanced SpeedStep Frequency Control> on cpu8 > est9: <Enhanced SpeedStep Frequency Control> on cpu9 > est10: <Enhanced SpeedStep Frequency Control> on cpu10 > est11: <Enhanced SpeedStep Frequency Control> on cpu11 > est12: <Enhanced SpeedStep Frequency Control> on cpu12 > est13: <Enhanced SpeedStep Frequency Control> on cpu13 > est14: <Enhanced SpeedStep Frequency Control> on cpu14 > est15: <Enhanced SpeedStep Frequency Control> on cpu15 > est16: <Enhanced SpeedStep Frequency Control> on cpu16 > est17: <Enhanced SpeedStep Frequency Control> on cpu17 > est18: <Enhanced SpeedStep Frequency Control> on cpu18 > est19: <Enhanced SpeedStep Frequency Control> on cpu19 > est20: <Enhanced SpeedStep Frequency Control> on cpu20 > est21: <Enhanced SpeedStep Frequency Control> on cpu21 > est22: <Enhanced SpeedStep Frequency Control> on cpu22 > est23: <Enhanced SpeedStep Frequency Control> on cpu23 > random: unblocking device. > usbus0: 5.0Gbps Super Speed USB v3.0 > Timecounters tick every 1.000 msec > hdacc0: <Cirrus Logic (0x4208) HDA CODEC> at cad 0 on hdac0 > hdaa0: <Cirrus Logic (0x4208) Audio Function Group> at nid 1 on hdacc0 > pcm0: <Cirrus Logic (0x4208) (Analog)> at nid 18 and 24 on hdaa0 > pcm1: <Cirrus Logic (0x4208) (Analog Headphones)> at nid 16 on hdaa0 > pcm2: <Cirrus Logic (0x4208) (Analog Line-out)> at nid 19 on hdaa0 > pcm3: <Cirrus Logic (0x4208) (Digital)> at nid 33 on hdaa0 > usbus1: 480Mbps High Speed USB v2.0 > ugen0.1: <0x1b73> at usbus0 > uhub0: <0x1b73 XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus0 > ugen1.1: <Intel> at usbus1 > uhub1: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1 > ada0 at ahcich0 bus 0 scbus0 target 0 lun 0 > ada0: <APPLE SSD SM1024F UXM8JA1Q> ATA8-ACS SATA 3.x device > ada0: Serial Number S1FVNYAF903719 > ada0: 600.000MB/s transfers (SATA 3.x, UDMA6, PIO 8192bytes) > ada0: Command Queueing enabled > ada0: 954204MB (1954210120 512 byte sectors: 16H 63S/T 16383C) > ada0: Previously was known as ad4 > lapic1: Forcing LINT1 to edge trigger > SMP: AP CPU #1 Launched! > lapic6: Forcing LINT1 to edge trigger > SMP: AP CPU #6 Launched! > lapic7: Forcing LINT1 to edge trigger > SMP: AP CPU #7 Launched! > lapic3: Forcing LINT1 to edge trigger > SMP: AP CPU #3 Launched! > lapic19: Forcing LINT1 to edge trigger > SMP: AP CPU #15 Launched! > lapic22: Forcing LINT1 to edge trigger > SMP: AP CPU #18 Launched! > lapic26: Forcing LINT1 to edge trigger > SMP: AP CPU #22 Launched! > lapic23: Forcing LINT1 to edge trigger > SMP: AP CPU #19 Launched! > lapic9: Forcing LINT1 to edge trigger > SMP: AP CPU #9 Launched! > lapic27: Forcing LINT1 to edge trigger > SMP: AP CPU #23 Launched! > lapic24: Forcing LINT1 to edge trigger > SMP: AP CPU #20 Launched! > lapic25: Forcing LINT1 to edge trigger > SMP: AP CPU #21 Launched! > lapic10: Forcing LINT1 to edge trigger > SMP: AP CPU #10 Launched! > lapic4: Forcing LINT1 to edge trigger > SMP: AP CPU #4 Launched! > lapic5: Forcing LINT1 to edge trigger > SMP: AP CPU #5 Launched! > lapic18: Forcing LINT1 to edge trigger > SMP: AP CPU #14 Launched! > lapic8: Forcing LINT1 to edge trigger > SMP: AP CPU #8 Launched! > lapic11: Forcing LINT1 to edge trigger > SMP: AP CPU #11 Launched! > lapic17: Forcing LINT1 to edge trigger > SMP: AP CPU #13 Launched! > lapic2: Forcing LINT1 to edge trigger > SMP: AP CPU #2 Launched! > lapic16: Forcing LINT1 to edge trigger > SMP: AP CPU #12 Launched! > lapic21: Forcing LINT1 to edge trigger > SMP: AP CPU #17 Launched! > lapic20: Forcing LINT1 to edge trigger > SMP: AP CPU #16 Launched! > Timecounter "TSC-low" frequency 1350029784 Hz quality 1000 > Root mount waiting for: usbus1 usbus0 > uhub0: 8 ports with 8 removable, self powered > uhub1: 2 ports with 2 removable, self powered > ugen0.2: <Logitech> at usbus0 > Root mount waiting for: usbus1 usbus0 > ugen1.2: <vendor 0x8087> at usbus1 > uhub2: <vendor 0x8087 product 0x0024, class 9/0, rev 2.00/0.00, addr 2> on > usbus1 > ugen0.3: <vendor 0x05ac> at usbus0 > uhub3: <vendor 0x05ac product 0x1008, class 9/0, rev 2.00/0.01, addr 2> on > usbus0 > uhub3: 1 port with 1 removable, bus powered > Root mount waiting for: usbus1 usbus0 > ugen0.4: <vendor 0x05ac> at usbus0 > uhub4: <vendor 0x05ac product 0x9132, class 9/0, rev 2.00/1.01, addr 3> on > usbus0 > uhub4: MTT enabled > uhub2: 8 ports with 7 removable, self powered > uhub4: 3 ports with 2 removable, self powered > Root mount waiting for: usbus1 usbus0 > ugen1.3: <Apple Inc.> at usbus1 > uhub5: <Apple Inc. BRCM20702 Hub, class 9/0, rev 2.00/1.00, addr 3> on > usbus1 > ugen0.5: <vendor 0x05ac> at usbus0 > hid_get_item: Number of items truncated to 255 > uhub5: 3 ports with 0 removable, self powered > Root mount waiting for: usbus1 usbus0 > ugen1.4: <vendor 0x05ac> at usbus1 > ukbd0: <vendor 0x05ac product 0x820a, class 0/0, rev 2.00/1.00, addr 4> on > usbus1 > kbd1 at ukbd0 > ugen0.6: <Apple, Inc.> at usbus0 > uhub6: <Apple, Inc. Keyboard Hub, class 9/0, rev 2.00/96.15, addr 5> on > usbus0 > uhub6: 3 ports with 2 removable, bus powered > ugen1.5: <vendor 0x05ac> at usbus1 > Root mount waiting for: usbus1 usbus0 > ugen0.7: <Apple, Inc> at usbus0 > ukbd1: <Apple, Inc Apple Keyboard, class 0/0, rev 2.00/0.69, addr 6> on > usbus0 > kbd2 at ukbd1 > ugen1.6: <Apple Inc.> at usbus1 > Trying to mount root from ufs:/dev/ada0p2 [rw]... > ums0: <Logitech USB Optical Mouse, class 0/0, rev 2.00/72.00, addr 1> on > usbus0 > ums1: <vendor 0x05ac product 0x820b, class 0/0, rev 2.00/1.00, addr 5> on > usbus1 > ums1: 3 buttons and [XY] coordinates ID=2 > ums0: 3 buttons and [XYZ] coordinates ID=0 > hid_get_item: Number of items truncated to 255 > hid_get_item: Number of items truncated to 255 > uhid0: <vendor 0x05ac product 0x9232, class 0/0, rev 1.10/1.14, addr 4> on > usbus0 > hid_get_item: Number of items truncated to 255 > hid_get_item: Number of items truncated to 255 > hid_get_item: Number of items truncated to 255 > uhid1: <Apple, Inc Apple Keyboard, class 0/0, rev 2.00/0.69, addr 6> on > usbus0 > ubt0: <Apple Inc. Bluetooth USB Host Controller, rev 2.00/1.06, addr 6> on > usbus1 > WARNING: attempt to domain_add(bluetooth) after domainfinalize() > WARNING: attempt to domain_add(netgraph) after domainfinalize() > ng_hci_send_command: ubt0hci - could not send HCI command, error=12 > ng_hci_process_command_timeout: ubt0hci - unable to complete HCI command > OGF=0x3, OCF=0x3. Timeout > > Regards > Estartu > > -- > _______________________________________________ > freebsd-stable@freebsd.org mailing list > https://lists.freebsd.org/mailman/listinfo/freebsd-stable > To unsubscribe, send any mail to "freebsd-stable-unsubscr...@freebsd.org" > _______________________________________________ freebsd-stable@freebsd.org mailing list https://lists.freebsd.org/mailman/listinfo/freebsd-stable To unsubscribe, send any mail to "freebsd-stable-unsubscr...@freebsd.org"
