On 05/28/11 21:56, Jeremy Chadwick wrote:
On Sat, May 28, 2011 at 09:10:11PM -0700, Michael Sinatra wrote:
I have a core-2 system with a 3ware SATA RAID controller for the
main disks and the built-in Intel ICH9 4-port SATA controller that
is only used for the DVDR. An 8-STABLE kernel csup'd and compiled
on April 25 works fine on this system. Kernels from source csup'd
this week are extremely unstable and usually panic or hang just
minutes after booting. The following warning messages appear after
the kernel probes the SATA controller and/or ICH9 USB controller and
continue about once per 1-2 seconds until the system crashes:
May 13 14:21:05 sonicyouth kernel: unknown: WARNING - ATAPI_IDENTIFY
requeued due to channel reset LBA=0
Disabling the ICH9 SATA controller in the BIOS allows the system to
boot and run normally.
Changes were made on April 28 to allow better support for 6-port
ICH9 controllers (SVN rev 221156) and I am wondering if my
controller is now being incorrectly recognized.
Here's the relevant kernel messages:
May 13 13:52:53 sonicyouth kernel: atapci1:<Intel ICH9 SATA300 controller>
port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x1c40-0x1c4f,0x1c30-0x1c3f at device 31.2
on pci0
May 13 13:52:53 sonicyouth kernel: ata0:<ATA channel 0> on atapci1
May 13 13:52:53 sonicyouth kernel: ata0: [ITHREAD]
May 13 13:52:53 sonicyouth kernel: ata1:<ATA channel 1> on atapci1
May 13 13:52:53 sonicyouth kernel: ata1: [ITHREAD]
May 13 13:52:53 sonicyouth kernel: atapci2:<Intel ICH9 SATA300> controller>
port 0x1cb8-0x1cbf,0x1cac-0x1caf,0x1cb0-0x1cb7,0x1ca8-0x1cab,0x1c60-0x1c6f,0x1c50-0x1c5f
irq 18 at device 31.5 on pci0
May 13 13:52:53 sonicyouth kernel: atapci2: [ITHREAD]
May 13 13:52:53 sonicyouth kernel: ata3:<ATA channel 0> on atapci2
May 13 13:52:53 sonicyouth kernel: ata3: [ITHREAD]
May 13 13:52:53 sonicyouth kernel: ata4:<ATA channel 1> on atapci2
May 13 13:52:53 sonicyouth kernel: ata4: [ITHREAD]
If I csup the most recent kernel sources, I get the same problem.
However, if, after csuping the latest kernel sources, I then fetch
the version of sys/dev/ata/ata-all.c as of April 27, everything
works fine. Here's the output of pciconf -l:
hostb0@pci0:0:0:0: class=0x060000 card=0xd98015d9 chip=0x29e08086 rev=0x01
hdr=0x00
pcib1@pci0:0:1:0: class=0x060400 card=0xd98015d9 chip=0x29e18086 rev=0x01
hdr=0x01
pcib2@pci0:0:6:0: class=0x060400 card=0xd98015d9 chip=0x29e98086 rev=0x01
hdr=0x01
em0@pci0:0:25:0: class=0x020000 card=0x10bd15d9 chip=0x10bd8086 rev=0x02
hdr=0x00
uhci0@pci0:0:26:0: class=0x0c0300 card=0xd98015d9 chip=0x29378086 rev=0x02
hdr=0x00
uhci1@pci0:0:26:1: class=0x0c0300 card=0xd98015d9 chip=0x29388086 rev=0x02
hdr=0x00
uhci2@pci0:0:26:2: class=0x0c0300 card=0xd98015d9 chip=0x29398086 rev=0x02
hdr=0x00
ehci0@pci0:0:26:7: class=0x0c0320 card=0xd98015d9 chip=0x293c8086 rev=0x02
hdr=0x00
none0@pci0:0:27:0: class=0x040300 card=0xd98015d9 chip=0x293e8086 rev=0x02
hdr=0x00
pcib3@pci0:0:28:0: class=0x060400 card=0xd98015d9 chip=0x29408086 rev=0x02
hdr=0x01
uhci3@pci0:0:29:0: class=0x0c0300 card=0xd98015d9 chip=0x29348086 rev=0x02
hdr=0x00
uhci4@pci0:0:29:1: class=0x0c0300 card=0xd98015d9 chip=0x29358086 rev=0x02
hdr=0x00
uhci5@pci0:0:29:2: class=0x0c0300 card=0xd98015d9 chip=0x29368086 rev=0x02
hdr=0x00
ehci1@pci0:0:29:7: class=0x0c0320 card=0xd98015d9 chip=0x293a8086 rev=0x02
hdr=0x00
pcib5@pci0:0:30:0: class=0x060401 card=0xd98015d9 chip=0x244e8086 rev=0x92
hdr=0x01
isab0@pci0:0:31:0: class=0x060100 card=0xd98015d9 chip=0x29168086 rev=0x02
hdr=0x00
atapci1@pci0:0:31:2: class=0x01018a card=0xd98015d9 chip=0x29208086 rev=0x02
hdr=0x00
none1@pci0:0:31:3: class=0x0c0500 card=0xd98015d9 chip=0x29308086 rev=0x02
hdr=0x00
atapci2@pci0:0:31:5: class=0x010185 card=0xd98015d9 chip=0x29268086 rev=0x02
hdr=0x00
none2@pci0:0:31:6: class=0x118000 card=0x000015d9 chip=0x29328086 rev=0x02
hdr=0x00
vgapci0@pci0:1:0:0: class=0x030000 card=0x216619da chip=0x0e2210de rev=0xa1
hdr=0x00
none3@pci0:1:0:1: class=0x040300 card=0x216619da chip=0x0beb10de rev=0xa1
hdr=0x00
twa0@pci0:3:0:0: class=0x010400 card=0x100413c1 chip=0x100413c1 rev=0x01
hdr=0x00
pcib4@pci0:5:0:0: class=0x060400 card=0x00000000 chip=0x032c8086 rev=0x09
hdr=0x01
ioapic0@pci0:5:0:1: class=0x080020 card=0xd98015d9 chip=0x03268086 rev=0x09
hdr=0x00
fwohci0@pci0:17:3:0: class=0x0c0010 card=0xba8015d9 chip=0x8023104c rev=0x00
hdr=0x00
atapci0@pci0:17:4:0: class=0x010185 card=0x82131283 chip=0x82131283 rev=0x00
hdr=0x00
This output doesn't help -- it's too terse. Please use "pciconf -lvbc"
instead.
Sorry about that. Here's the output:
sonicyouth# pciconf -lvbc
hostb0@pci0:0:0:0: class=0x060000 card=0xd98015d9 chip=0x29e08086
rev=0x01 hdr=0x00
vendor = 'Intel Corporation'
device = 'X38/X48 (Bearlake) Processor to I/O Controller'
class = bridge
subclass = HOST-PCI
cap 09[e0] = vendor (length 12) Intel cap 0 version 1
pcib1@pci0:0:1:0: class=0x060400 card=0xd98015d9 chip=0x29e18086
rev=0x01 hdr=0x01
vendor = 'Intel Corporation'
device = 'X38/X48 (Bearlake) PCIe Root Port 1'
class = bridge
subclass = PCI-PCI
cap 0d[88] = PCI Bridge card=0xd98015d9
cap 01[80] = powerspec 3 supports D0 D3 current D0
cap 05[90] = MSI supports 1 message
cap 10[a0] = PCI-Express 2 root port max data 128(128) link x16(x16)
ecap 0002[100] = VC 1 max VC0
ecap 0005[140] = unknown 1
pcib2@pci0:0:6:0: class=0x060400 card=0xd98015d9 chip=0x29e98086
rev=0x01 hdr=0x01
vendor = 'Intel Corporation'
device = 'X38/X48 (Bearlake) PCIe Root Port 2'
class = bridge
subclass = PCI-PCI
cap 0d[88] = PCI Bridge card=0xd98015d9
cap 01[80] = powerspec 3 supports D0 D3 current D0
cap 05[90] = MSI supports 1 message
cap 10[a0] = PCI-Express 2 root port max data 128(128) link x1(x16)
ecap 0002[100] = VC 1 max VC0
ecap 0005[140] = unknown 1
em0@pci0:0:25:0: class=0x020000 card=0x10bd15d9 chip=0x10bd8086
rev=0x02 hdr=0x00
vendor = 'Intel Corporation'
device = 'Intel 82566DM Gigabit Ethernet Adapter (82566DM)'
class = network
subclass = ethernet
bar [10] = type Memory, range 32, base 0xd8600000, size 131072,
enabled
bar [14] = type Memory, range 32, base 0xd8627000, size 4096, enabled
bar [18] = type I/O Port, range 32, base 0x1820, size 32, enabled
cap 01[c8] = powerspec 2 supports D0 D3 current D0
cap 05[d0] = MSI supports 1 message, 64 bit enabled with 1 message
cap 13[e0] = PCI Advanced Features: FLR TP
uhci0@pci0:0:26:0: class=0x0c0300 card=0xd98015d9 chip=0x29378086
rev=0x02 hdr=0x00
vendor = 'Intel Corporation'
device = '82801IB/IR/IH (ICH9 Family) USB Universal Host
Controller'
class = serial bus
subclass = USB
bar [20] = type I/O Port, range 32, base 0x1840, size 32, enabled
cap 13[50] = PCI Advanced Features: FLR TP
uhci1@pci0:0:26:1: class=0x0c0300 card=0xd98015d9 chip=0x29388086
rev=0x02 hdr=0x00
vendor = 'Intel Corporation'
device = '82801IB/IR/IH (ICH9 Family) USB Universal Host
Controller'
class = serial bus
subclass = USB
bar [20] = type I/O Port, range 32, base 0x1860, size 32, enabled
cap 13[50] = PCI Advanced Features: FLR TP
uhci2@pci0:0:26:2: class=0x0c0300 card=0xd98015d9 chip=0x29398086
rev=0x02 hdr=0x00
vendor = 'Intel Corporation'
device = '82801IB/IR/IH (ICH9 Family) USB Universal Host
Controller'
class = serial bus
subclass = USB
bar [20] = type I/O Port, range 32, base 0x1880, size 32, enabled
cap 13[50] = PCI Advanced Features: FLR TP
ehci0@pci0:0:26:7: class=0x0c0320 card=0xd98015d9 chip=0x293c8086
rev=0x02 hdr=0x00
vendor = 'Intel Corporation'
device = '82801IB/IR/IH (ICH9 Family) USB2 Enhanced Host
Controller'
class = serial bus
subclass = USB
bar [10] = type Memory, range 32, base 0xd8628000, size 1024, enabled
cap 01[50] = powerspec 2 supports D0 D3 current D0
cap 0a[58] = EHCI Debug Port at offset 0xa0 in map 0x14
cap 13[98] = PCI Advanced Features: FLR TP
none0@pci0:0:27:0: class=0x040300 card=0xd98015d9 chip=0x293e8086
rev=0x02 hdr=0x00
vendor = 'Intel Corporation'
device = '82801IB/IR/IH (ICH9 Family) HD Audio Controller'
class = multimedia
subclass = HDA
bar [10] = type Memory, range 64, base 0xd8620000, size 16384,
enabled
cap 01[50] = powerspec 2 supports D0 D3 current D0
cap 05[60] = MSI supports 1 message, 64 bit
cap 10[70] = PCI-Express 1 root endpoint max data 128(128) link x0(x0)
ecap 0002[100] = VC 1 max VC1
ecap 0005[130] = unknown 1
pcib3@pci0:0:28:0: class=0x060400 card=0xd98015d9 chip=0x29408086
rev=0x02 hdr=0x01
vendor = 'Intel Corporation'
device = '82801IB/IR/IH (ICH9 Family) PCIe Root Port 1'
class = bridge
subclass = PCI-PCI
cap 10[40] = PCI-Express 1 root port max data 128(128) link x4(x4)
cap 05[80] = MSI supports 1 message
cap 0d[90] = PCI Bridge card=0xd98015d9
cap 01[a0] = powerspec 2 supports D0 D3 current D0
ecap 0002[100] = VC 1 max VC0
ecap 0005[180] = unknown 1
uhci3@pci0:0:29:0: class=0x0c0300 card=0xd98015d9 chip=0x29348086
rev=0x02 hdr=0x00
vendor = 'Intel Corporation'
device = '82801IB/IR/IH (ICH9 Family) USB Universal Host
Controller'
class = serial bus
subclass = USB
bar [20] = type I/O Port, range 32, base 0x18a0, size 32, enabled
cap 13[50] = PCI Advanced Features: FLR TP
uhci4@pci0:0:29:1: class=0x0c0300 card=0xd98015d9 chip=0x29358086
rev=0x02 hdr=0x00
vendor = 'Intel Corporation'
device = '82801IB/IR/IH (ICH9 Family) USB Universal Host
Controller'
class = serial bus
subclass = USB
bar [20] = type I/O Port, range 32, base 0x18c0, size 32, enabled
cap 13[50] = PCI Advanced Features: FLR TP
uhci5@pci0:0:29:2: class=0x0c0300 card=0xd98015d9 chip=0x29368086
rev=0x02 hdr=0x00
vendor = 'Intel Corporation'
device = '82801IB/IR/IH (ICH9 Family) USB Universal Host
Controller'
class = serial bus
subclass = USB
bar [20] = type I/O Port, range 32, base 0x18e0, size 32, enabled
cap 13[50] = PCI Advanced Features: FLR TP
ehci1@pci0:0:29:7: class=0x0c0320 card=0xd98015d9 chip=0x293a8086
rev=0x02 hdr=0x00
vendor = 'Intel Corporation'
device = '82801IB/IR/IH (ICH9 Family) USB2 Enhanced Host
Controller'
class = serial bus
subclass = USB
bar [10] = type Memory, range 32, base 0xd8629000, size 1024, enabled
cap 01[50] = powerspec 2 supports D0 D3 current D0
cap 0a[58] = EHCI Debug Port at offset 0xa0 in map 0x14
cap 13[98] = PCI Advanced Features: FLR TP
pcib5@pci0:0:30:0: class=0x060401 card=0xd98015d9 chip=0x244e8086
rev=0x92 hdr=0x01
vendor = 'Intel Corporation'
device = '82801 Family (ICH2/3/4/5/6/7/8/9,63xxESB) Hub
Interface to PCI Bridge'
class = bridge
subclass = PCI-PCI
cap 0d[50] = PCI Bridge card=0xd98015d9
isab0@pci0:0:31:0: class=0x060100 card=0xd98015d9 chip=0x29168086
rev=0x02 hdr=0x00
vendor = 'Intel Corporation'
device = '82801IR (ICH9R) LPC Interface Controller'
class = bridge
subclass = PCI-ISA
cap 09[e0] = vendor (length 12) Intel cap 1 version 0
features: SATA RAID-5, 4 PCI-e x1 slots
atapci1@pci0:0:31:2: class=0x01018a card=0xd98015d9 chip=0x29208086
rev=0x02 hdr=0x00
vendor = 'Intel Corporation'
device = '82801IB/IR/IH (ICH9 Family) 4 port Serial ATA Storage
Controller 1'
class = mass storage
subclass = ATA
bar [10] = type I/O Port, range 32, base 0x1f0, size 8, enabled
bar [14] = type I/O Port, range 32, base 0x3f4, size 1, enabled
bar [18] = type I/O Port, range 32, base 0x170, size 8, enabled
bar [1c] = type I/O Port, range 32, base 0x374, size 1, enabled
bar [20] = type I/O Port, range 32, base 0x1c40, size 16, enabled
bar [24] = type I/O Port, range 32, base 0x1c30, size 16, enabled
cap 01[70] = powerspec 3 supports D0 D3 current D0
cap 13[b0] = PCI Advanced Features: FLR TP
none1@pci0:0:31:3: class=0x0c0500 card=0xd98015d9 chip=0x29308086
rev=0x02 hdr=0x00
vendor = 'Intel Corporation'
device = 'Intel(R) ICH9 Family SMBus Controller working fine
with http://download.cnet.com/Chipset-Driver-Inte (8086)'
class = serial bus
subclass = SMBus
bar [10] = type Memory, range 64, base 0xd862a000, size 256, enabled
bar [20] = type I/O Port, range 32, base 0x1100, size 32, enabled
atapci2@pci0:0:31:5: class=0x010185 card=0xd98015d9 chip=0x29268086
rev=0x02 hdr=0x00
vendor = 'Intel Corporation'
device = '82801IB/IR/IH (ICH9 Family) 2 port Serial ATA Storage
Controller 2'
class = mass storage
subclass = ATA
bar [10] = type I/O Port, range 32, base 0x1cb8, size 8, enabled
bar [14] = type I/O Port, range 32, base 0x1cac, size 4, enabled
bar [18] = type I/O Port, range 32, base 0x1cb0, size 8, enabled
bar [1c] = type I/O Port, range 32, base 0x1ca8, size 4, enabled
bar [20] = type I/O Port, range 32, base 0x1c60, size 16, enabled
bar [24] = type I/O Port, range 32, base 0x1c50, size 16, enabled
cap 01[70] = powerspec 3 supports D0 D3 current D0
cap 13[b0] = PCI Advanced Features: FLR TP
none2@pci0:0:31:6: class=0x118000 card=0x000015d9 chip=0x29328086
rev=0x02 hdr=0x00
vendor = 'Intel Corporation'
device = '82801IB/IR/IH (ICH9 Family) Thermal Subsystem'
class = dasp
bar [10] = type Memory, range 64, base 0xd862b000, size 4096, enabled
cap 01[50] = powerspec 3 supports D0 D3 current D0
vgapci0@pci0:1:0:0: class=0x030000 card=0x216619da chip=0x0e2210de
rev=0xa1 hdr=0x00
vendor = 'NVIDIA Corporation'
class = display
subclass = VGA
bar [10] = type Memory, range 32, base 0xd6000000, size 33554432,
enabled
bar [14] = type Prefetchable Memory, range 64, base 0xc8000000,
size 134217728, enabled
bar [1c] = type Prefetchable Memory, range 64, base 0xd0000000,
size 67108864, enabled
bar [24] = type I/O Port, range 32, base 0x2000, size 128, enabled
cap 01[60] = powerspec 3 supports D0 D3 current D0
cap 05[68] = MSI supports 1 message, 64 bit
cap 10[78] = PCI-Express 1 endpoint max data 128(128) link x16(x16)
cap 09[b4] = vendor (length 20)
ecap 0002[100] = VC 1 max VC0
ecap 0004[128] = unknown 1
ecap 000b[600] = unknown 1
none3@pci0:1:0:1: class=0x040300 card=0x216619da chip=0x0beb10de
rev=0xa1 hdr=0x00
vendor = 'NVIDIA Corporation'
class = multimedia
subclass = HDA
bar [10] = type Memory, range 32, base 0xd8000000, size 16384,
enabled
cap 01[60] = powerspec 3 supports D0 D3 current D0
cap 05[68] = MSI supports 1 message, 64 bit
cap 10[78] = PCI-Express 1 endpoint max data 128(128) link x16(x16)
twa0@pci0:3:0:0: class=0x010400 card=0x100413c1 chip=0x100413c1
rev=0x01 hdr=0x00
vendor = '3ware Inc'
device = 'PCI-Express SATA2 Raid Controller (9650SE Series)'
class = mass storage
subclass = RAID
bar [10] = type Prefetchable Memory, range 64, base 0xd4000000,
size 33554432, enabled
bar [18] = type Memory, range 64, base 0xd8100000, size 4096, enabled
bar [20] = type I/O Port, range 32, base 0x3000, size 256, enabled
cap 01[40] = powerspec 2 supports D0 D1 D2 D3 current D0
cap 05[50] = MSI supports 32 messages, 64 bit
cap 10[70] = PCI-Express 1 legacy endpoint max data 128(512) link
x1(x8)
ecap 0001[100] = AER 1 0 fatal 1 non-fatal 1 corrected
pcib4@pci0:5:0:0: class=0x060400 card=0x00000000 chip=0x032c8086
rev=0x09 hdr=0x01
vendor = 'Intel Corporation'
device = 'PCI Express-to-PCI Express Bridge (6702PXH)'
class = bridge
subclass = PCI-PCI
cap 10[44] = PCI-Express 1 PCI bridge max data 128(256) link x4(x8)
cap 05[5c] = MSI supports 1 message, 64 bit
cap 01[6c] = powerspec 2 supports D0 D3 current D0
cap 07[d8] = PCI-X bridge
ecap 0001[100] = AER 1 0 fatal 1 non-fatal 0 corrected
ecap 0004[300] = unknown 1
ioapic0@pci0:5:0:1: class=0x080020 card=0xd98015d9 chip=0x03268086
rev=0x09 hdr=0x00
vendor = 'Intel Corporation'
device = '6700/6702PXH I/OxAPIC Interrupt Controller A'
class = base peripheral
subclass = interrupt controller
bar [10] = type Memory, range 32, base 0xd8300000, size 4096, enabled
cap 10[44] = PCI-Express 1 endpoint max data 256(256) link x4(x8)
cap 01[6c] = powerspec 2 supports D0 D3 current D0
fwohci0@pci0:17:3:0: class=0x0c0010 card=0xba8015d9 chip=0x8023104c
rev=0x00 hdr=0x00
vendor = 'Texas Instruments (TI)'
device = 'IEEE1394a-2000 OHCI PHY/Link-Layer Ctrlr (TSB43AB21/A)'
class = serial bus
subclass = FireWire
bar [10] = type Memory, range 32, base 0xd8204000, size 2048, enabled
bar [14] = type Memory, range 32, base 0xd8200000, size 16384,
enabled
cap 01[44] = powerspec 2 supports D0 D1 D2 D3 current D0
atapci0@pci0:17:4:0: class=0x010185 card=0x82131283 chip=0x82131283
rev=0x00 hdr=0x00
vendor = 'Integrated Technology Express (ITE) Inc'
device = 'IDE Controller (IT8213F)'
class = mass storage
subclass = ATA
bar [10] = type I/O Port, range 32, base 0x4020, size 8, enabled
bar [14] = type I/O Port, range 32, base 0x4014, size 4, enabled
bar [18] = type I/O Port, range 32, base 0x4018, size 8, enabled
bar [1c] = type I/O Port, range 32, base 0x4010, size 4, enabled
bar [20] = type I/O Port, range 32, base 0x4000, size 16, enabled
cap 01[80] = powerspec 2 supports D0 D3 current D0
Thank you for tracking the issue down to something between roughly
April 25th and April 29th.
It looked from SVN as if the April 28th MFCs had caused the issue, but I
can't narrow it down further, other than to note that replacing
ata-all.c with an older version (as of April 27 it was "$FreeBSD:
src/sys/dev/ata/ata-all.c,v 1.308.2.20 2011/04/19 17:01:05 mav Exp $")
allowed me to boot with SATA enabled.
Different revisions/models of the ICH9 offer AHCI capability. Does your
system BIOS let you toggle this? If so, I would recommend enabling it
then trying to use ahci.ko ("load ahci.ko" from the loader "ok" prompt,
or ahci_load="yes" in /boot/loader.conf) to see if things improve. Your
CD drive will then appear as a SCSI-esque CD drive (e.g. cd(4) driver
instead of atapicd), so be aware. This would be a workaround for your
issue, assuming it works.
Right now, I am not at my workstation (I left the office a while ago),
and probably won't be back until Tuesday. I'll try it then, if I don't
get to it sooner.
I've CC'd mav@ who has likely committed something that's causing this
issue, but unknown at this time. Relevant cvsweb details which someone
can sift through:
http://www.freebsd.org/cgi/cvsweb.cgi/src/sys/dev/ata/
michael
_______________________________________________
freebsd-stable@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-stable
To unsubscribe, send any mail to "freebsd-stable-unsubscr...@freebsd.org"
