Cool, so stable/7 will just need to be updated :) I need to catch up all the
drivers in that stream actually. Thanks for testing!! Jack On Thu, Nov 19, 2009 at 8:58 AM, Mike Tancsa <m...@sentex.net> wrote: > At 07:29 PM 11/18/2009, Jack Vogel wrote: > >> Hey Mike, >> >> Can you check if you see the same behavior on RELENG 8? >> > > For RELENG_8. I installed an fxp card and netbooted off it. > > I assigned an IP address to the onboard nic (em5). Pinged itself, got a MAC > and response. Plugged in the cable, pinged the other side, all ok > > Did the same, but pinged the other side, and plugged the cable in, all > worked as expected. > # ping 10.177.194.18 > PING 10.177.194.18 (10.177.194.18): 56 data bytes > ping: sendto: Host is down > ping: sendto: Host is down > ping: sendto: Host is down > 64 bytes from 10.177.194.18: icmp_seq=30 ttl=64 time=1329.918 ms > 64 bytes from 10.177.194.18: icmp_seq=31 ttl=64 time=324.925 ms > 64 bytes from 10.177.194.18: icmp_seq=32 ttl=64 time=0.054 ms > 64 bytes from 10.177.194.18: icmp_seq=33 ttl=64 time=0.055 ms > 64 bytes from 10.177.194.18: icmp_seq=34 ttl=64 time=0.047 ms > 64 bytes from 10.177.194.18: icmp_seq=35 ttl=64 time=0.050 ms > 64 bytes from 10.177.194.18: icmp_seq=36 ttl=64 time=0.047 ms > 64 bytes from 10.177.194.18: icmp_seq=37 ttl=64 time=0.049 ms > 64 bytes from 10.177.194.18: icmp_seq=38 ttl=64 time=0.043 ms > > > em4: <Intel(R) PRO/1000 Network Connection 6.9.14> port 0xcc00-0xcc1f mem > 0xfaee0000-0xfaefffff,0xfaedc000-0xfaedffff irq 16 at device 0.0 on pci6 > > em4: Using MSIX interrupts > em4: [ITHREAD] > em4: [ITHREAD] > em4: [ITHREAD] > em4: Ethernet address: 00:30:48:d6:ef:12 > pcib7: <ACPI PCI-PCI bridge> irq 16 at device 28.1 on pci0 > pci7: <ACPI PCI bus> on pcib7 > em5: <Intel(R) PRO/1000 Network Connection 6.9.14> port 0xdc00-0xdc1f mem > 0xfafe0000-0xfaffffff,0xfafdc000-0xfafdffff irq 17 at device 0.0 on pci7 > > em5: Using MSIX interrupts > em5: [ITHREAD] > em5: [ITHREAD] > em5: [ITHREAD] > em5: Ethernet address: 00:30:48:d6:ef:13 > > So the problem is _not_ there under RELENG_8. I also tested the 2 PCIe > nics to make sure they are still working, and they are. > > Full dmesg below > > opyright (c) 1992-2009 The FreeBSD Project. > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > The Regents of the University of California. All rights reserved. > FreeBSD is a registered trademark of The FreeBSD Foundation. > FreeBSD 8.0-RC2 #0: Wed Nov 11 09:54:52 EST 2009 > mdtan...@ich10.sentex.ca:/usr/obj/usr/src/sys/alix i386 > Timecounter "i8254" frequency 1193182 Hz quality 0 > CPU: Intel(R) Core(TM) i7 CPU 920 @ 2.67GHz (2660.00-MHz 686-class > CPU) > Origin = "GenuineIntel" Id = 0x106a5 Stepping = 5 > > > Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> > > > Features2=0x98e3bd<SSE3,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,SSE4.1,SSE4.2,POPCNT> > AMD Features=0x28100000<NX,RDTSCP,LM> > AMD Features2=0x1<LAHF> > TSC: P-state invariant > real memory = 6446645248 (6148 MB) > avail memory = 3137355776 (2992 MB) > ACPI APIC Table: <011209 APIC2037> > FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs > FreeBSD/SMP: 1 package(s) x 4 core(s) > cpu0 (BSP): APIC ID: 0 > cpu1 (AP): APIC ID: 2 > cpu2 (AP): APIC ID: 4 > cpu3 (AP): APIC ID: 6 > ioapic0: Changing APIC ID to 1 > ioapic0 <Version 2.0> irqs 0-23 on motherboard > kbd1 at kbdmux0 > cryptosoft0: <software crypto> on motherboard > acpi0: <011209 XSDT2037> on motherboard > acpi0: [ITHREAD] > acpi0: Power Button (fixed) > acpi0: reservation of 0, a0000 (3) failed > acpi0: reservation of 100000, bff00000 (3) failed > Timecounter "ACPI-safe" frequency 3579545 Hz quality 850 > acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0 > pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 > pci0: <ACPI PCI bus> on pcib0 > pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0 > pci1: <ACPI PCI bus> on pcib1 > em0: <Intel(R) PRO/1000 Network Connection 6.9.14> port 0xac00-0xac1f mem > 0xface0000-0xfacfffff,0xfacc0000-0xfacdffff irq 16 at device 0.0 on pci1 > > em0: Using MSI interrupt > em0: [FILTER] > em0: Ethernet address: 00:15:17:78:e6:e0 > em1: <Intel(R) PRO/1000 Network Connection 6.9.14> port 0xa880-0xa89f mem > 0xfac80000-0xfac9ffff,0xfac60000-0xfac7ffff irq 17 at device 0.1 on pci1 > > em1: Using MSI interrupt > em1: [FILTER] > em1: Ethernet address: 00:15:17:78:e6:e1 > pcib2: <ACPI PCI-PCI bridge> at device 3.0 on pci0 > pci2: <ACPI PCI bus> on pcib2 > pcib3: <ACPI PCI-PCI bridge> at device 5.0 on pci0 > pci3: <ACPI PCI bus> on pcib3 > em2: <Intel(R) PRO/1000 Network Connection 6.9.14> port 0xbc00-0xbc1f mem > 0xfade0000-0xfadfffff,0xfadc0000-0xfaddffff irq 16 at device 0.0 on pci3 > > em2: Using MSI interrupt > em2: [FILTER] > em2: Ethernet address: 00:15:17:cf:26:de > em3: <Intel(R) PRO/1000 Network Connection 6.9.14> port 0xb880-0xb89f mem > 0xfad80000-0xfad9ffff,0xfad60000-0xfad7ffff irq 17 at device 0.1 on pci3 > > em3: Using MSI interrupt > em3: [FILTER] > em3: Ethernet address: 00:15:17:cf:26:df > pcib4: <ACPI PCI-PCI bridge> at device 7.0 on pci0 > pci4: <ACPI PCI bus> on pcib4 > pcib5: <ACPI PCI-PCI bridge> at device 9.0 on pci0 > pci5: <ACPI PCI bus> on pcib5 > pci0: <base peripheral, interrupt controller> at device 16.0 (no driver > attached) > pci0: <base peripheral, interrupt controller> at device 16.1 (no driver > attached) > pci0: <base peripheral, interrupt controller> at device 20.0 (no driver > attached) > pci0: <base peripheral, interrupt controller> at device 20.1 (no driver > attached) > pci0: <base peripheral, interrupt controller> at device 20.2 (no driver > attached) > pci0: <base peripheral, interrupt controller> at device 20.3 (no driver > attached) > pci0: <base peripheral> at device 22.0 (no driver attached) > pci0: <base peripheral> at device 22.1 (no driver attached) > pci0: <base peripheral> at device 22.2 (no driver attached) > pci0: <base peripheral> at device 22.3 (no driver attached) > pci0: <base peripheral> at device 22.4 (no driver attached) > pci0: <base peripheral> at device 22.5 (no driver attached) > pci0: <base peripheral> at device 22.6 (no driver attached) > pci0: <base peripheral> at device 22.7 (no driver attached) > uhci0: <UHCI (generic) USB controller> port 0x9c00-0x9c1f irq 16 at device > 26.0 on pci0 > uhci0: [ITHREAD] > uhci0: LegSup = 0x2f00 > usbus0: <UHCI (generic) USB controller> on uhci0 > uhci1: <UHCI (generic) USB controller> port 0x9880-0x989f irq 21 at device > 26.1 on pci0 > uhci1: [ITHREAD] > uhci1: LegSup = 0x2f00 > usbus1: <UHCI (generic) USB controller> on uhci1 > uhci2: <UHCI (generic) USB controller> port 0x9800-0x981f irq 19 at device > 26.2 on pci0 > uhci2: [ITHREAD] > uhci2: LegSup = 0x2f00 > usbus2: <UHCI (generic) USB controller> on uhci2 > ehci0: <EHCI (generic) USB 2.0 controller> mem 0xfabde000-0xfabde3ff irq 18 > at device 26.7 on pci0 > ehci0: [ITHREAD] > usbus3: EHCI version 1.0 > usbus3: <EHCI (generic) USB 2.0 controller> on ehci0 > pcib6: <ACPI PCI-PCI bridge> irq 17 at device 28.0 on pci0 > pci6: <ACPI PCI bus> on pcib6 > em4: <Intel(R) PRO/1000 Network Connection 6.9.14> port 0xcc00-0xcc1f mem > 0xfaee0000-0xfaefffff,0xfaedc000-0xfaedffff irq 16 at device 0.0 on pci6 > > em4: Using MSIX interrupts > em4: [ITHREAD] > em4: [ITHREAD] > em4: [ITHREAD] > em4: Ethernet address: 00:30:48:d6:ef:12 > pcib7: <ACPI PCI-PCI bridge> irq 16 at device 28.1 on pci0 > pci7: <ACPI PCI bus> on pcib7 > em5: <Intel(R) PRO/1000 Network Connection 6.9.14> port 0xdc00-0xdc1f mem > 0xfafe0000-0xfaffffff,0xfafdc000-0xfafdffff irq 17 at device 0.0 on pci7 > > em5: Using MSIX interrupts > em5: [ITHREAD] > em5: [ITHREAD] > em5: [ITHREAD] > em5: Ethernet address: 00:30:48:d6:ef:13 > uhci3: <UHCI (generic) USB controller> port 0x9480-0x949f irq 23 at device > 29.0 on pci0 > uhci3: [ITHREAD] > uhci3: LegSup = 0x2f00 > usbus4: <UHCI (generic) USB controller> on uhci3 > uhci4: <UHCI (generic) USB controller> port 0x9400-0x941f irq 19 at device > 29.1 on pci0 > uhci4: [ITHREAD] > uhci4: LegSup = 0x2f00 > usbus5: <UHCI (generic) USB controller> on uhci4 > uhci5: <UHCI (generic) USB controller> port 0x9080-0x909f irq 18 at device > 29.2 on pci0 > uhci5: [ITHREAD] > uhci5: LegSup = 0x2f00 > usbus6: <UHCI (generic) USB controller> on uhci5 > ehci1: <EHCI (generic) USB 2.0 controller> mem 0xfabdc000-0xfabdc3ff irq 23 > at device 29.7 on pci0 > ehci1: [ITHREAD] > usbus7: EHCI version 1.0 > usbus7: <EHCI (generic) USB 2.0 controller> on ehci1 > pcib8: <ACPI PCI-PCI bridge> at device 30.0 on pci0 > pci8: <ACPI PCI bus> on pcib8 > fxp0: <Intel 82550 Pro/100 Ethernet> port 0xec00-0xec3f mem > 0xfbefe000-0xfbefefff,0xfbec0000-0xfbedffff irq 17 at device 1.0 on pci8 > miibus0: <MII bus> on fxp0 > inphy0: <i82555 10/100 media interface> PHY 1 on miibus0 > inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto > fxp0: Ethernet address: 00:02:b3:5d:ca:ce > fxp0: [ITHREAD] > vgapci0: <VGA-compatible display> mem > 0xf9800000-0xf9ffffff,0xfbef8000-0xfbefbfff,0xfb000000-0xfb7fffff irq 17 at > device 4.0 on pci8 > isab0: <PCI-ISA bridge> at device 31.0 on pci0 > isa0: <ISA bus> on isab0 > atapci0: <Intel ICH10 SATA300 controller> port > 0x9000-0x9007,0x8c00-0x8c03,0x8880-0x8887,0x8800-0x8803,0x8480-0x848f,0x8400-0x840f > irq 19 at device 31.2 on pci0 > atapci0: [ITHREAD] > ata2: <ATA channel 0> on atapci0 > ata2: [ITHREAD] > ata3: <ATA channel 1> on atapci0 > ata3: [ITHREAD] > pci0: <serial bus, SMBus> at device 31.3 (no driver attached) > atapci1: <Intel ICH10 SATA300 controller> port > 0x8000-0x8007,0x7c00-0x7c03,0x7880-0x7887,0x7800-0x7803,0x7480-0x748f,0x7400-0x740f > irq 19 at device 31.5 on pci0 > atapci1: [ITHREAD] > ata4: <ATA channel 0> on atapci1 > ata4: [ITHREAD] > ata5: <ATA channel 1> on atapci1 > ata5: [ITHREAD] > acpi_button0: <Power Button> on acpi0 > atrtc0: <AT realtime clock> port 0x70-0x71 irq 8 on acpi0 > uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0 > uart0: [FILTER] > uart0: console (38400,n,8,1) > uart1: <16550 or compatible> port 0x2f8-0x2ff irq 3 on acpi0 > uart1: [FILTER] > uart2: <16550 or compatible> port 0x3e8-0x3ef irq 5 on acpi0 > uart2: [FILTER] > atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0 > atkbd0: <AT Keyboard> irq 1 on atkbdc0 > kbd0 at atkbd0 > atkbd0: [GIANT-LOCKED] > atkbd0: [ITHREAD] > cpu0: <ACPI CPU> on acpi0 > ACPI Warning: Incorrect checksum in table [OEMB] - 8A, should be 87 > 20090521 tbutils-275 > est0: <Enhanced SpeedStep Frequency Control> on cpu0 > est: CPU supports Enhanced Speedstep, but is not recognized. > est: cpu_vendor GenuineIntel, msr 14 > device_attach: est0 attach returned 6 > p4tcc0: <CPU Frequency Thermal Control> on cpu0 > cpu1: <ACPI CPU> on acpi0 > est1: <Enhanced SpeedStep Frequency Control> on cpu1 > est: CPU supports Enhanced Speedstep, but is not recognized. > est: cpu_vendor GenuineIntel, msr 14 > device_attach: est1 attach returned 6 > p4tcc1: <CPU Frequency Thermal Control> on cpu1 > cpu2: <ACPI CPU> on acpi0 > est2: <Enhanced SpeedStep Frequency Control> on cpu2 > est: CPU supports Enhanced Speedstep, but is not recognized. > est: cpu_vendor GenuineIntel, msr 14 > device_attach: est2 attach returned 6 > p4tcc2: <CPU Frequency Thermal Control> on cpu2 > cpu3: <ACPI CPU> on acpi0 > est3: <Enhanced SpeedStep Frequency Control> on cpu3 > est: CPU supports Enhanced Speedstep, but is not recognized. > est: cpu_vendor GenuineIntel, msr 14 > device_attach: est3 attach returned 6 > p4tcc3: <CPU Frequency Thermal Control> on cpu3 > pmtimer0 on isa0 > orm0: <ISA Option ROMs> at iomem 0xc0000-0xc7fff,0xc8000-0xc97ff pnpid > ORM0000 on isa0 > sc0: <System console> at flags 0x100 on isa0 > sc0: VGA <16 virtual consoles, flags=0x100> > vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 > ata0 at port 0x1f0-0x1f7,0x3f6 irq 14 on isa0 > ata0: [ITHREAD] > ata1 at port 0x170-0x177,0x376 irq 15 on isa0 > ata1: [ITHREAD] > Timecounters tick every 1.000 msec > IPsec: Initialized Security Association Processing. > usbus0: 12Mbps Full Speed USB v1.0 > usbus1: 12Mbps Full Speed USB v1.0 > usbus2: 12Mbps Full Speed USB v1.0 > usbus3: 480Mbps High Speed USB v2.0 > usbus4: 12Mbps Full Speed USB v1.0 > usbus5: 12Mbps Full Speed USB v1.0 > usbus6: 12Mbps Full Speed USB v1.0 > usbus7: 480Mbps High Speed USB v2.0 > SMP: AP CPU #1 Launched! > SMP: AP CPU #2 Launched! > SMP: AP CPU #3 Launched! > ugen1.1: <Intel> at usbus1ugen0.1: <Intel> at usbus0Root mount waiting > for:ugen2.1: <Intel> at usbus2 > > > usbus7 usbus6 usbus5 usbus4 usbus3 usbus2 usbus1 usbus0 > uhub0: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0 > ugen3.1: <Intel> at usbus3uhub1: > <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus2 > uhub2: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1 > uhub3: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus3 > ugen4.1: <Intel> at usbus4ugen5.1: <Intel> at usbus5ugen7.1: <Intel> at > usbus7ugen6.1: <Intel> at usbus6 > uhub4: > <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus4 > > uhub5: > <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus5 > uhub6: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus6 > uhub7: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus7 > uhub0: 2 ports with 2 removable, self powered > uhub1: 2 ports with 2 removable, self powered > uhub2: 2 ports with 2 removable, self powered > uhub4: 2 ports with 2 removable, self powered > uhub5: 2 ports with 2 removable, self powered > uhub6: 2 ports with 2 removable, self powered > Root mount waiting for: usbus7 usbus3 > Root mount waiting for: usbus7 usbus3 > uhub3: 6 ports with 6 removable, self powered > uhub7: 6 ports with 6 removable, self powered > Trying to mount root from nfs:10.255.255.1:/home/pxe > NFS ROOT: 10.255.255.1:/usr/home/pxe/ > > > ---Mike > > > -------------------------------------------------------------------- > Mike Tancsa, tel +1 519 651 3400 > Sentex Communications, m...@sentex.net > Providing Internet since 1994 www.sentex.net > Cambridge, Ontario Canada www.sentex.net/mike > > _______________________________________________ freebsd-stable@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-stable To unsubscribe, send any mail to "freebsd-stable-unsubscr...@freebsd.org"
