>
> On Sun, 8 Feb 2009, Danny Braniss wrote:
>
> >> On Sun, 8 Feb 2009, Danny Braniss wrote:
> >>
> >>> looking at the bce source, it's not clear (to me :-). If errors are
> >>> detected in bce_rx_intr(), the packet gets dropped, which I would expect
> >>> to be the treatment of an offloded chekcum error, but it seems that is
> >>> not
> >>> the case.
> >>
> >> I think we're thinking of different checksums -- devices/device drivers
> >> drop frames with bad ethernet checksums, but not IP and above layer
> >> checksums.
> >
> > I know I'm stepping on thin ice hear - haven't touched Stevens for a while,
> > (and I doubt it mentions offloading), but if the offload checksum is bad,
> > why not just drop the packet?
> >
> > The way I read the driver, if the offload checksum is on, and if no errors
> > where detected, then it's marked as ok.
>
> There are a few good reasons I can think of, but this is hardly a
> comprehensive list:
>
> (1) If there are bad higher level checksums on the wire, you want to see them
> in tcpdump, so allow them to get up to a higher layer if network layer
> checksums aren't good.
>
> (2) It's a matter of local policy as to whether UDP checksums (for example)
> are observed or not.
>
> (3) If you're forwarding or bridging packets, it should be up to the end nodes
> how they deal with bad UDP checksums on packets to them, not the routers.
ok, I can understand the logic.
>
> Looking at if_bce.c, the following seems to be reasonable logic; first,
> ethernet-layer checksums:
>
> 5902 /* Check the received frame for errors. */
> 5903 if (status & (L2_FHDR_ERRORS_BAD_CRC |
> 5904 L2_FHDR_ERRORS_PHY_DECODE |
> L2_FHDR_ERRORS_ALIGNMENT |
> 5905 L2_FHDR_ERRORS_TOO_SHORT |
> L2_FHDR_ERRORS_GIANT_FRAME)) {
> 5906
> 5907 /* Log the error and release the mbuf. */
> 5908 ifp->if_ierrors++;
> 5909 DBRUN(sc->l2fhdr_status_errors++);
> 5910
> 5911 m_freem(m0);
> 5912 m0 = NULL;
> 5913 goto bce_rx_int_next_rx;
> 5914 }
>
> I.e., if there are ethernet-level CRC failures, drop the packet.
>
> 5922 /* Validate the checksum if offload enabled. */
> 5923 if (ifp->if_capenable & IFCAP_RXCSUM) {
> 5924
> 5925 /* Check for an IP datagram. */
> 5926 if (!(status & L2_FHDR_STATUS_SPLIT) &&
> 5927 (status & L2_FHDR_STATUS_IP_DATAGRAM)) {
> 5928 m0->m_pkthdr.csum_flags |=
> CSUM_IP_CHECKED;
> 5929
> 5930 /* Check if the IP checksum is valid. */
> 5931 if ((l2fhdr->l2_fhdr_ip_xsum ^ 0xffff)
> ==
> 0)
> 5932 m0->m_pkthdr.csum_flags |=
> CSUM_IP_VALID;
> 5933 }
> 5934
> 5935 /* Check for a valid TCP/UDP frame. */
> 5936 if (status & (L2_FHDR_STATUS_TCP_SEGMENT |
> 5937 L2_FHDR_STATUS_UDP_DATAGRAM)) {
> 5938
> 5939 /* Check for a good TCP/UDP checksum. */
> 5940 if ((status & (L2_FHDR_ERRORS_TCP_XSUM |
> 5941 L2_FHDR_ERRORS_UDP_XSUM))
> == 0) {
> 5942 m0->m_pkthdr.csum_data =
> 5943 l2fhdr->l2_fhdr_tcp_udp_xsum;
> 5944 m0->m_pkthdr.csum_flags |=
> (CSUM_DATA_VALID
> 5945 | CSUM_PSEUDO_HDR);
> 5946 }
> 5947 }
> 5948 }
>
> Only look at higher level checksums if policy enables it on the interface;
> then, only if the hardware has a view on the IP-layer checksums, propagte
> that
> information to the mbuf flags from the descriptor ring entry flags, both
> whether or not the checksum was verified, and whether or not it was good. If
> policy disables it, or the hardware expresses no view, we don't set flags,
> which simply defers checksumming to a higher layer (if required -- for
> forwarded packets, we won't test UDP-layer checksums at all).
I missed line 5928, and as usual, your explanation is most educational!
The comment in line 5939 is a bit missleading, the way I read the code, it
does not check for good checksum.
Cheers,
danny
_______________________________________________
freebsd-stable@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-stable
To unsubscribe, send any mail to "freebsd-stable-unsubscr...@freebsd.org"
