Hello, Finally I found what is the problem.
from ACPI CA release notes: ... 14 May 2008. Summary of changes for version 20080514: 1) ACPI CA Core Subsystem: Fixed a problem where GPEs were enabled too early during the ACPICA initialization. This could lead to "handler not installed" errors on some machines. Moved GPE enable until after _REG/_STA/_INI methods are run. This ensures that all operation regions and devices throughout the namespace have been initialized before GPEs are enabled. Alexey Starikovskiy, BZ 9916. ... See the attached patch for possible workaround of the problem. References: http://lists.freebsd.org/pipermail/freebsd-acpi/2008-October/005167.html Best Regards Torfinn Ingolfsen wrote: > On Fri, 09 Jan 2009 10:01:33 +0200 > Krassimir Slavchev <kra...@bulinfo.net> wrote: > >> I have found that thread. > > FWIW, I started a new thread[1] on freebsd-mobile, to update the status > now after FreeBSD 7.1 has been released > >> The problem may be with allocating resources by ACPI PCI-PCI bridge. >> There is a way to set needed values: >> http://lists.freebsd.org/pipermail/freebsd-acpi/2008-May/004905.html > > Interesting. For my laptop, it seems that these bridges have the > problem: > pcib2: <ACPI PCI-PCI bridge> irq 17 at device 28.0 on pci0 > pcib2: domain 0 > pcib2: secondary bus 2 > pcib2: subordinate bus 2 > pcib2: I/O decode 0x0-0x0 > pcib2: no prefetched decode > pci2: <ACPI PCI bus> on pcib2 > pci2: domain=0, physical bus=2 > pcib3: <ACPI PCI-PCI bridge> irq 16 at device 28.1 on pci0 > pcib3: domain 0 > pcib3: secondary bus 3 > pcib3: subordinate bus 3 > pcib3: I/O decode 0x0-0x0 > pcib3: no prefetched decode > pci3: <ACPI PCI bus> on pcib3 > pci3: domain=0, physical bus=3 > > and also these: > > pcib4: <ACPI PCI-PCI bridge> irq 18 at device 28.2 on pci0 > pcib4: domain 0 > pcib4: secondary bus 4 > pcib4: subordinate bus 4 > pcib4: I/O decode 0x0-0x0 > pcib4: no prefetched decode > pci4: <ACPI PCI bus> on pcib4 > pci4: domain=0, physical bus=4 > > pcib5: <ACPI PCI-PCI bridge> irq 19 at device 28.3 on pci0 > pcib5: domain 0 > pcib5: secondary bus 5 > pcib5: subordinate bus 7 > pcib5: I/O decode 0x0-0x0 > pcib5: no prefetched decode > pcib5: could not get PCI interrupt routing table for \\_SB_.PCI0.RP04 - > AE_NOT_FOUND > pci5: <ACPI PCI bus> on pcib5 > pci5: domain=0, physical bus=5 > > bge0 (the wired interface is on pcib4: > > bge0: <Broadcom NetXtreme Gigabit Ethernet Controller, ASIC rev. 0x4201> irq > 18 at device 0.0 on pci4 > pcib4: bge0 requested unsupported memory range 0-0xffffffff (decoding 0-0, > 0-0) > bge0: 0x10000 bytes of rid 0x10 res 3 failed (0, 0xffffffff). > bge0: couldn't map memory > device_attach: bge0 attach returned 6 > > and wpi0 (the wireless) is on pcib3: > > wpi0: <Intel(R) PRO/Wireless 3945ABG> irq 17 at device 0.0 on pci3 > wpi0: Driver Revision 20071127 > pcib3: wpi0 requested unsupported memory range 0-0xffffffff (decoding 0-0, > 0-0) > wpi0: 0x1000 bytes of rid 0x10 res 3 failed (0, 0xffffffff). > wpi0: could not allocate memory resource > device_attach: wpi0 attach returned 6 > > With acpi disabled, the bridges shoiw up like this: > pcib2: <PCI-PCI bridge> irq 17 at device 28.0 on pci0 > pcib2: domain 0 > pcib2: secondary bus 2 > pcib2: subordinate bus 2 > pcib2: I/O decode 0xf000-0xfff > pcib2: no prefetched decode > pci2: <PCI bus> on pcib2 > pci2: domain=0, physical bus=2 > pcib3: <PCI-PCI bridge> irq 16 at device 28.1 on pci0 > pcib3: domain 0 > pcib3: secondary bus 3 > pcib3: subordinate bus 3 > pcib3: I/O decode 0xf000-0xfff > pcib3: memory decode 0xc8200000-0xc82fffff > pcib3: no prefetched decode > pci3: <PCI bus> on pcib3 > pci3: domain=0, physical bus=3 > > pcib4: <PCI-PCI bridge> irq 18 at device 28.2 on pci0 > pcib4: domain 0 > pcib4: secondary bus 4 > pcib4: subordinate bus 4 > pcib4: I/O decode 0xf000-0xfff > pcib4: memory decode 0xc8300000-0xc83fffff > pcib4: no prefetched decode > pci4: <PCI bus> on pcib4 > pci4: domain=0, physical bus=4 > > pcib5: <PCI-PCI bridge> irq 19 at device 28.3 on pci0 > pcib5: domain 0 > pcib5: secondary bus 5 > pcib5: subordinate bus 5 > pcib5: I/O decode 0xf000-0xfff > pcib5: no prefetched decode > pci5: <PCI bus> on pcib5 > pci5: domain=0, physical bus=5 > > bge with acpi disabled: > > bge0: <Broadcom NetXtreme Gigabit Ethernet Controller, ASIC rev. 0x4201> mem > 0xc8300000-0xc830ffff irq 17 at device 0.0 on pci4 > bge0: Reserved 0x10000 bytes for rid 0x10 type 3 at 0xc8300000 > bge0: attempting to allocate 1 MSI vectors (8 supported) > msi: routing MSI IRQ 256 to vector 48 > bge0: using IRQ 256 for MSI > miibus0: <MII bus> on bge0 > brgphy0: <BCM5750 10/100/1000baseTX PHY> PHY 1 on miibus0 > brgphy0: OUI 0x000818, model 0x0018, rev. 0 > brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, > 1000baseT-FDX, auto > bge0: bpf attached > bge0: Ethernet address: 00:16:36:54:a9:ae > bge0: [MPSAFE] > bge0: [ITHREAD] > > wpi with acpi disabled: > wpi0: <Intel(R) PRO/Wireless 3945ABG> mem 0xc8200000-0xc8200fff irq 17 at > device 0.0 on pci3 > wpi0: Driver Revision 20071127 > wpi0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xc8200000 > wpi0: Hardware Revision (0x1) > wpi0: Regulatory Domain: MoW2 > wpi0: Hardware Type: B > wpi0: Hardware Revision: ? > wpi0: SKU does support 802.11a > wpi0: bpf attached > wpi0: Ethernet address: 00:13:02:3e:d4:ce > wpi0: bpf attached > wpi0: bpf attached > ioapic0: Assigning PCI IRQ 17 to local APIC 0 > ioapic0: routing intpin 17 (PCI IRQ 17) to vector 60 > wpi0: [MPSAFE] > wpi0: [ITHREAD] > wpi0: 11a rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps > wpi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps > wpi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps > 36Mbps 48Mbps 54Mbps > > Perhaps I should try to patch my pci too. > > References: > 1) > http://lists.freebsd.org/pipermail/freebsd-mobile/2009-January/011294.html
--- sys/dev/acpica/acpi_ec.c.orig 2009-01-14 16:52:40.000000000 +0200
+++ sys/dev/acpica/acpi_ec.c 2009-01-14 16:58:05.000000000 +0200
@@ -828,6 +828,11 @@
if (need_poll) {
static int once;
+ /*
+ * XXX Workaround for ACPI CA versions < 20080514
+ */
+ sleep(1);
+
if (EcCheckStatus(sc, "pre-check", Event) == AE_OK) {
if (!once) {
device_printf(sc->ec_dev,
signature.asc
Description: OpenPGP digital signature
