I recently replaced FreeBSD 4.10 with a completely, fresh install of FreeBSD 5.3. The FreeBSD 5.3-RELEASE GENERIC kernel did not recognize either of these devices after installation, nor does my present SMP kernel. All these devices worked fine with FreeBSD 4.10 SMP using the current motherboard settings. FreeBSD 5.3 correctly recognizes an ISA-PNP soundcard (Audiotrix 3D-XG) which works fine with the Opensound System. The 1542CP and the printer port are the only problem devices as far as I can tell. They are recognized at the correct resources, but note the following messages.
aha0 failed to probe on isa0 [I have previously tried setting specific resources that I know to be appropriate in device.hints, and still get
the same message.]
ppc0: parallel port found at 0x378 ppc0: using extended I/O port range ppc0: <Parallel port> failed to probe at port 0x378-0x37f irq 7 on isa0
I have attached two text files: device.hints and dmesg-v.txt (verbose boot).
Thank you,
Rick Voland [EMAIL PROTECTED]
# $FreeBSD: src/sys/i386/conf/GENERIC.hints,v 1.13 2004/04/01 21:48:31 alfred Exp $ hint.acpi.0.disabled="1" hint.fdc.0.at="isa" hint.fdc.0.port="0x3F0" hint.fdc.0.irq="6" hint.fdc.0.drq="2" hint.fd.0.at="fdc0" hint.fd.0.drive="0" hint.fd.1.at="fdc0" hint.fd.1.drive="1" hint.ata.0.at="isa" hint.ata.0.port="0x1F0" hint.ata.0.irq="14" hint.ata.1.at="isa" hint.ata.1.port="0x170" hint.ata.1.irq="15" hint.adv.0.at="isa" hint.adv.0.disabled="1" hint.bt.0.at="isa" hint.bt.0.disabled="1" hint.aha.0.at="isa" #hint.aha.0.irq="11" #hint.aha.0.port="0x334" #hint.aha.0.maddr="0xcc000" #hint.aha.0.drq="7" # hint.aha.0.disabled="1" hint.aic.0.at="isa" hint.aic.0.disabled="1" hint.atkbdc.0.at="isa" hint.atkbdc.0.port="0x060" hint.atkbd.0.at="atkbdc" hint.atkbd.0.irq="1" hint.psm.0.at="atkbdc" hint.psm.0.irq="12" hint.psm.0.disabled="1" hint.vga.0.at="isa" hint.sc.0.at="isa" hint.sc.0.flags="0x100" hint.vt.0.at="isa" hint.vt.0.disabled="1" hint.apm.0.disabled="1" hint.apm.0.flags="0x20" hint.pcic.0.at="isa" #hint.pcic.0.irq="10" # Default to polling hint.pcic.0.disabled="1" hint.pcic.0.port="0x3e0" hint.pcic.0.maddr="0xd0000" hint.pcic.1.at="isa" hint.pcic.1.irq="11" hint.pcic.1.port="0x3e2" hint.pcic.1.maddr="0xd4000" hint.pcic.1.disabled="1" hint.sio.0.at="isa" hint.sio.0.port="0x3F8" hint.sio.0.flags="0x10" hint.sio.0.irq="4" hint.sio.1.at="isa" hint.sio.1.port="0x2F8" hint.sio.1.irq="3" hint.sio.1.disabled="1" hint.sio.2.at="isa" hint.sio.2.disabled="1" hint.sio.2.port="0x3E8" hint.sio.2.irq="5" hint.sio.3.at="isa" hint.sio.3.disabled="1" hint.sio.3.port="0x2E8" hint.sio.3.irq="9" hint.ppc.0.at="isa" hint.ppc.0.irq="7" hint.ed.0.at="isa" hint.ed.0.disabled="1" hint.ed.0.port="0x280" hint.ed.0.irq="10" hint.ed.0.maddr="0xd8000" hint.cs.0.at="isa" hint.cs.0.disabled="1" hint.cs.0.port="0x300" hint.sn.0.at="isa" hint.sn.0.disabled="1" hint.sn.0.port="0x300" hint.sn.0.irq="10" hint.ie.0.at="isa" hint.ie.0.disabled="1" hint.ie.0.port="0x300" hint.ie.0.irq="10" hint.ie.0.maddr="0xd0000" hint.fe.0.at="isa" hint.fe.0.disabled="1" hint.fe.0.port="0x300" hint.lnc.0.at="isa" hint.lnc.0.disabled="1" hint.lnc.0.port="0x280" hint.lnc.0.irq="10" hint.lnc.0.drq="0"
Copyright (c) 1992-2004 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.3-RELEASE-p2 #1: Tue Dec 28 21:44:33 CST 2004
[EMAIL PROTECTED]:/usr/obj/usr/src/sys/BRIAN
Preloaded elf kernel "/boot/kernel/kernel" at 0xc0a06000.
Calibrating clock(s) ... i8254 clock: 1193086 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz quality 0
Calibrating TSC clock ... TSC clock: 232671718 Hz
CPU: Pentium/P55C (232.67-MHz 586-class CPU)
Origin = "GenuineIntel" Id = 0x543 Stepping = 3
Features=0x8003bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8,APIC,MMX>
real memory = 268435456 (256 MB)
Physical memory chunk(s):
0x0000000000001000 - 0x000000000009efff, 647168 bytes (158 pages)
0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages)
0x0000000000c29000 - 0x000000000fb4ffff, 250769408 bytes (61223 pages)
avail memory = 253038592 (241 MB)
MP Configuration Table version 1.1 found at 0xc00f1400
APIC: Using the MPTable enumerator.
SMP: Added CPU 0 (BSP)
SMP: Added CPU 1 (AP)
MPTable: <OEM00000 PROD00000000>
APIC ID: physical 0, logical 0:0
APIC ID: physical 1, logical 0:1
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
cpu0 (BSP): APIC ID: 0
cpu1 (AP): APIC ID: 1
bios32: Found BIOS32 Service Directory header at 0xc00fb090
bios32: Entry = 0xfb510 (c00fb510) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0xf0000+0xb540
pnpbios: Found PnP BIOS data at 0xc00fc070
pnpbios: Entry = f0000:c098 Rev = 1.0
Other BIOS signatures found:
Intel Pentium detected, installing workaround for F00F bug
ioapic0: Assuming intbase of 0
ioapic0: Routing external 8259A's -> intpin 0
ioapic0: intpin 0 -> ExtINT (edge, high)
ioapic0: intpin 1 -> ISA IRQ 1 (edge, high)
ioapic0: intpin 2 -> ISA IRQ 2 (edge, high)
ioapic0: intpin 3 -> ISA IRQ 3 (edge, high)
ioapic0: intpin 4 -> ISA IRQ 4 (edge, high)
ioapic0: intpin 5 -> ISA IRQ 5 (edge, high)
ioapic0: intpin 6 -> ISA IRQ 6 (edge, high)
ioapic0: intpin 7 -> ISA IRQ 7 (edge, high)
ioapic0: intpin 8 -> ISA IRQ 8 (edge, high)
ioapic0: intpin 9 -> ISA IRQ 9 (edge, high)
ioapic0: intpin 10 -> ISA IRQ 10 (edge, high)
ioapic0: intpin 11 -> ISA IRQ 11 (edge, high)
ioapic0: intpin 12 -> ISA IRQ 12 (edge, high)
ioapic0: intpin 13 -> ISA IRQ 13 (edge, high)
ioapic0: intpin 14 -> ISA IRQ 14 (edge, high)
ioapic0: intpin 15 -> ISA IRQ 15 (edge, high)
ioapic0: intpin 16 -> PCI IRQ 16 (level, low)
ioapic0: intpin 17 -> PCI IRQ 17 (level, low)
ioapic0: intpin 18 -> PCI IRQ 18 (level, low)
ioapic0: intpin 19 -> PCI IRQ 19 (level, low)
ioapic0: intpin 20 -> PCI IRQ 20 (level, low)
ioapic0: intpin 21 -> PCI IRQ 21 (level, low)
ioapic0: intpin 22 -> PCI IRQ 22 (level, low)
ioapic0: intpin 23 -> PCI IRQ 23 (level, low)
ioapic0: intpin 1 bus ISA
ioapic0: intpin 1 trigger: edge
ioapic0: intpin 1 polarity: high
ioapic0: intpin 2 bus ISA
ioapic0: Routing IRQ 0 -> intpin 2
ioapic0: intpin 2 trigger: edge
ioapic0: intpin 2 polarity: high
ioapic0: intpin 4 bus ISA
ioapic0: intpin 4 trigger: edge
ioapic0: intpin 4 polarity: high
ioapic0: intpin 5 bus ISA
ioapic0: intpin 5 trigger: edge
ioapic0: intpin 5 polarity: high
ioapic0: intpin 6 bus ISA
ioapic0: intpin 6 trigger: edge
ioapic0: intpin 6 polarity: high
ioapic0: intpin 7 bus ISA
ioapic0: intpin 7 trigger: edge
ioapic0: intpin 7 polarity: high
ioapic0: intpin 8 bus ISA
ioapic0: intpin 8 trigger: edge
ioapic0: intpin 8 polarity: high
ioapic0: intpin 10 bus ISA
ioapic0: intpin 10 trigger: edge
ioapic0: intpin 10 polarity: high
ioapic0: intpin 11 bus ISA
ioapic0: intpin 11 trigger: edge
ioapic0: intpin 11 polarity: high
ioapic0: intpin 13 bus ISA
ioapic0: intpin 13 trigger: edge
ioapic0: intpin 13 polarity: high
ioapic0: intpin 14 bus ISA
ioapic0: intpin 14 trigger: edge
ioapic0: intpin 14 polarity: high
ioapic0: intpin 15 bus ISA
ioapic0: intpin 15 trigger: edge
ioapic0: intpin 15 polarity: high
ioapic0: intpin 16 bus ISA
ioapic0: Routing IRQ 12 -> intpin 16
ioapic0: intpin 12 disabled
ioapic0: intpin 16 trigger: level
ioapic0: intpin 16 polarity: low
ioapic0: intpin 17 bus ISA
ioapic0: Routing IRQ 3 -> intpin 17
ioapic0: intpin 3 disabled
ioapic0: intpin 17 trigger: level
ioapic0: intpin 17 polarity: low
ioapic0: intpin 18 bus ISA
ioapic0: Routing IRQ 9 -> intpin 18
ioapic0: intpin 9 disabled
ioapic0: intpin 18 trigger: level
ioapic0: intpin 18 polarity: low
lapic: Routing ExtINT -> LINT0
lapic: Routing NMI -> LINT1
ioapic0 <Version 1.1> irqs 0-23 on motherboard
cpu0 BSP:
ID: 0x00000000 VER: 0x00030010 LDR: 0x01000000 DFR: 0x0fffffff
lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
wlan: <802.11 Link Layer>
null: <null device, zero device>
random: <entropy source, Software, Yarrow>
io: <I/O>
mem: <memory>
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
pci_open(1): mode 1 addr port (0x0cf8) is 0x8000005c
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=12508086)
pcibios: BIOS version 2.10
Found $PIR table, 5 entries at 0xc00fde10
PCI-Only Interrupts: 3 9 12
Location Bus Device Pin Link IRQs
slot 1 0 20 A 0x60 3 4 5 7 9 10 11 12 14 15
slot 1 0 20 B 0x61 3 4 5 7 9 10 11 12 14 15
slot 1 0 20 C 0x62 3 4 5 7 9 10 11 12 14 15
slot 1 0 20 D 0x63 3 4 5 7 9 10 11 12 14 15
slot 2 0 19 A 0x61 3 4 5 7 9 10 11 12 14 15
slot 2 0 19 B 0x62 3 4 5 7 9 10 11 12 14 15
slot 2 0 19 C 0x63 3 4 5 7 9 10 11 12 14 15
slot 2 0 19 D 0x60 3 4 5 7 9 10 11 12 14 15
slot 3 0 18 A 0x62 3 4 5 7 9 10 11 12 14 15
slot 3 0 18 B 0x63 3 4 5 7 9 10 11 12 14 15
slot 3 0 18 C 0x60 3 4 5 7 9 10 11 12 14 15
slot 3 0 18 D 0x61 3 4 5 7 9 10 11 12 14 15
slot 4 0 17 A 0x63 3 4 5 7 9 10 11 12 14 15
slot 4 0 17 B 0x60 3 4 5 7 9 10 11 12 14 15
slot 4 0 17 C 0x61 3 4 5 7 9 10 11 12 14 15
slot 4 0 17 D 0x62 3 4 5 7 9 10 11 12 14 15
pcib0: <Host to PCI bridge> pcibus 0 on motherboard
pir0: <PCI Interrupt Routing Table: 5 Entries> on motherboard
$PIR: Links after initial probe:
Link IRQ Rtd Ref IRQs
0x60 255 N 4 3 4 5 7 9 10 11 12 14 15
0x61 255 N 4 3 4 5 7 9 10 11 12 14 15
0x62 255 N 4 3 4 5 7 9 10 11 12 14 15
0x63 255 N 4 3 4 5 7 9 10 11 12 14 15
$PIR: Found matching pin for 0.20.INTA at func 0: 12
$PIR: Found matching pin for 0.19.INTA at func 0: 3
$PIR: Found matching pin for 0.18.INTA at func 0: 9
$PIR: Links after initial IRQ discovery:
Link IRQ Rtd Ref IRQs
0x60 12 Y 4 3 4 5 7 9 10 11 12 14 15
0x61 3 Y 4 3 4 5 7 9 10 11 12 14 15
0x62 9 Y 4 3 4 5 7 9 10 11 12 14 15
0x63 255 N 4 3 4 5 7 9 10 11 12 14 15
$PIR: IRQs used by BIOS: 3 9 12
$PIR: Interrupt Weights:
[ 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 ]
[ 0 0 0 4 0 0 0 0 0 4 0 0 4 0 0 0 ]
pci0: <PCI bus> on pcib0
pci0: physical bus=0
found-> vendor=0x8086, dev=0x1250, revid=0x03
bus=0, slot=0, func=0
class=06-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0006, statreg=0x2200, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x7000, revid=0x01
bus=0, slot=7, func=0
class=06-01-00, hdrtype=0x00, mfdev=1
cmdreg=0x000f, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[20]: type 4, range 32, base 0000f000, size 4, enabled
found-> vendor=0x8086, dev=0x7010, revid=0x00
bus=0, slot=7, func=1
class=01-01-80, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[10]: type 3, range 32, base e0000000, size 24, enabled
map[14]: type 4, range 32, base 00006400, size 8, enabled
map[18]: type 1, range 32, base e1000000, size 12, enabled
$PIR: 0:18 INTA routed to irq 9
found-> vendor=0x1002, dev=0x4750, revid=0x5c
bus=0, slot=18, func=0
class=03-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0087, statreg=0x0280, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns)
intpin=a, irq=9
map[10]: type 4, range 32, base 00006800, size 7, enabled
map[14]: type 1, range 32, base e1001000, size 7, enabled
$PIR: 0:19 INTA routed to irq 3
found-> vendor=0x10b7, dev=0x9055, revid=0x30
bus=0, slot=19, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x0a (2500 ns), maxlat=0x0a (2500 ns)
intpin=a, irq=3
powerspec 1 supports D0 D1 D2 D3 current D0
map[10]: type 4, range 32, base 00006c00, size 5, enabled
$PIR: 0:20 INTA routed to irq 12
found-> vendor=0x1044, dev=0xa400, revid=0x02
bus=0, slot=20, func=0
class=01-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0200, cachelnsz=8 (dwords)
lattimer=0xa0 (4800 ns), mingnt=0x04 (1000 ns), maxlat=0x08 (2000 ns)
intpin=a, irq=12
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX3 WDMA2 controller> port
0xf000-0xf00f,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 7.1 on pci0
atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0xf000
ata0: channel #0 on atapci0
atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0
atapci0: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6
ata0: reset tp1 mask=03 ostat0=50 ostat1=00
ata0-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00
ata0-slave: stat=0x00 err=0x01 lsb=0x00 msb=0x00
ata0: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ata0: [MPSAFE]
ata1: channel #1 on atapci0
atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170
atapci0: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376
ata1: reset tp1 mask=03 ostat0=50 ostat1=00
ata1-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00
ata1-slave: stat=0x00 err=0x01 lsb=0x00 msb=0x00
ata1: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ata1: [MPSAFE]
pci0: <display, VGA> at device 18.0 (no driver attached)
xl0: <3Com 3c905B-TX Fast Etherlink XL> port 0x6800-0x687f mem
0xe1001000-0xe100107f irq 3 at device 19.0 on pci0
xl0: Reserved 0x80 bytes for rid 0x14 type 3 at 0xe1001000
xl0: using memory mapped I/O
xl0: media options word: a
xl0: found MII/AUTO
miibus0: <MII bus> on xl0
xlphy0: <3Com internal media interface> on miibus0
xlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
xl0: bpf attached
xl0: Ethernet address: 00:04:76:17:0b:48
xl0: [MPSAFE]
dpt0: <DPT Caching SCSI RAID Controller> port 0x6c00-0x6c1f irq 12 at device
20.0 on pci0
dpt0: Reserved 0x20 bytes for rid 0x10 type 4 at 0x6c00
dpt0: DPT PM2044UW FW Rev. 07H1, 1 channel, 64 CCBs
dpt0: [GIANT-LOCKED]
cpu0 on motherboard
cpu1 on motherboard
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
Trying Read_Port at 203
MPI0001: start dependent (0)
MPI0001: adding io range 0x220-0x22f, size=0x10, align=0x10
MPI0001: adding io range 0x530-0x537, size=0x8, align=0x8
MPI0001: adding io range 0x388-0x38b, size=0x4, align=0x4
MPI0001: adding io range 0x330-0x331, size=0x2, align=0x2
MPI0001: adding io range 0x370-0x371, size=0x2, align=0x2
MPI0001: adding irq mask 0x400
MPI0001: adding irq mask 0x20
MPI0001: adding dma mask 0x1
MPI0001: adding dma mask 0x2
MPI0001: start dependent (1)
MPI0001: adding io range 0x240-0x24f, size=0x10, align=0x10
MPI0001: adding io range 0xe80-0xe87, size=0x8, align=0x8
MPI0001: adding io range 0x388-0x38b, size=0x4, align=0x4
MPI0001: adding io range 0x300-0x301, size=0x2, align=0x2
MPI0001: adding io range 0x100-0xfff, size=0x2, align=0x2
MPI0001: adding irq mask 0xe80
MPI0001: adding irq mask 0x6a0
MPI0001: adding dma mask 0xb
MPI0001: adding dma mask 0xb
MPI0001: start dependent (2)
MPI0001: adding io range 0x220-0x28f, size=0x10, align=0x10
MPI0001: adding io range 0x530-0xf4f, size=0x8, align=0x8
MPI0001: adding io range 0x388-0x3fb, size=0x4, align=0x8
MPI0001: adding io range 0x300-0x335, size=0x2, align=0x2
MPI0001: adding io range 0x100-0xfff, size=0x2, align=0x2
MPI0001: adding irq mask 0xea0
MPI0001: adding irq mask 0xea0
MPI0001: adding dma mask 0xb
MPI0001: adding dma mask 0xb
MPI0001: end dependent
MPI0002: start dependent (0)
MPI0002: adding io range 0x201-0x201, size=0x1, align=0x1
MPI0002: start dependent (1)
MPI0002: adding io range 0x202-0x202, size=0x1, align=0x1
MPI0002: start dependent (1)
MPI0002: adding io range 0x203-0x203, size=0x1, align=0x1
MPI0002: start dependent (1)
MPI0002: adding io range 0x204-0x20f, size=0x1, align=0x1
MPI0002: end dependent
ADP1542: adding irq mask 0xdc00
ADP1542: adding dma mask 0xe0
ADP1542: start dependent (0)
ADP1542: adding io range 0x330-0x333, size=0x4, align=0x4
ADP1542: start dependent (1)
ADP1542: adding io range 0x334-0x337, size=0x4, align=0x4
ADP1542: start dependent (1)
ADP1542: adding io range 0x234-0x237, size=0x4, align=0x4
ADP1542: start dependent (1)
ADP1542: adding io range 0x230-0x233, size=0x4, align=0x4
ADP1542: start dependent (1)
ADP1542: adding io range 0x134-0x137, size=0x4, align=0x4
ADP1542: start dependent (2)
ADP1542: adding io range 0x130-0x133, size=0x4, align=0x4
ADP1542: end dependent
ADP1542: adding memory range 0xc8000-0xdffff, size=0x4000, align=0x4000
ex_isa_identify()
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
pnpbios: 13 devices, largest 126 bytes
PNP0200: adding dma mask 0x10
PNP0200: adding io range 0-0xf, size=0x10, align=0
PNP0200: adding io range 0x81-0x83, size=0x3, align=0
PNP0200: adding io range 0x87-0x87, size=0x1, align=0
PNP0200: adding io range 0x89-0x8b, size=0x3, align=0
PNP0200: adding io range 0x8f-0x91, size=0x3, align=0
PNP0200: adding io range 0xc0-0xdf, size=0x20, align=0
pnpbios: handle 1 device ID PNP0200 (0002d041)
PNP0100: adding irq mask 0x1
PNP0100: adding io range 0x40-0x43, size=0x4, align=0
pnpbios: handle 2 device ID PNP0100 (0001d041)
PNP0b00: adding irq mask 0x100
PNP0b00: adding io range 0x70-0x71, size=0x2, align=0
pnpbios: handle 3 device ID PNP0b00 (000bd041)
PNP0303: adding irq mask 0x2
PNP0303: adding io range 0x60-0x60, size=0x1, align=0
PNP0303: adding io range 0x64-0x64, size=0x1, align=0
pnpbios: handle 4 device ID PNP0303 (0303d041)
PNP0800: adding io range 0x61-0x61, size=0x1, align=0
pnpbios: handle 5 device ID PNP0800 (0008d041)
PNP0c04: adding irq mask 0x2000
PNP0c04: adding io range 0xf0-0xff, size=0x10, align=0
pnpbios: handle 6 device ID PNP0c04 (040cd041)
PNP0c01: adding fixed memory32 range 0xf0000-0xf3fff, size=0x4000
PNP0c01: adding fixed memory32 range 0xf4000-0xf7fff, size=0x4000
PNP0c01: adding fixed memory32 range 0xf8000-0xfbfff, size=0x4000
PNP0c01: adding fixed memory32 range 0xfc000-0xfffff, size=0x4000
PNP0c01: adding fixed memory32 range 0-0x9ffff, size=0xa0000
PNP0c01: adding fixed memory32 range 0xfffe0000-0xffffffff, size=0x20000
PNP0c01: adding fixed memory32 range 0xfec00000-0xfec0ffff, size=0x10000
PNP0c01: adding fixed memory32 range 0xfee00000-0xfee0ffff, size=0x10000
PNP0c01: adding fixed memory32 range 0x100000-0xfffffff, size=0xff00000
pnpbios: handle 7 device ID PNP0c01 (010cd041)
PNP0a03: adding io range 0x4d0-0x4d1, size=0x2, align=0
PNP0a03: adding io range 0xcf8-0xcff, size=0x8, align=0
PNP0a03: adding io range 0x480-0x48f, size=0x10, align=0
pnpbios: handle 8 device ID PNP0a03 (030ad041)
PNP0c02: adding io range 0x208-0x20f, size=0x8, align=0
pnpbios: handle 9 device ID PNP0c02 (020cd041)
PNP0501: adding irq mask 0x10
PNP0501: adding io range 0x3f8-0x3ff, size=0x8, align=0
pnpbios: handle 10 device ID PNP0501 (0105d041)
PNP0700: adding dma mask 0x4
PNP0700: adding io range 0x3f2-0x3f5, size=0x4, align=0
PNP0700: adding irq mask 0x40
pnpbios: handle 11 device ID PNP0700 (0007d041)
PNP0400: adding irq mask 0x80
PNP0400: adding io range 0x378-0x37f, size=0x8, align=0
pnpbios: handle 12 device ID PNP0400 (0004d041)
ahc_isa_probe 6: ioport 0x6c00 alloc failed
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <ISA Option ROMs> at iomem
0xcc000-0xcffff,0xc8000-0xc8fff,0xc0000-0xc7fff on isa0
pmtimer0 on isa0
adv0: not probed (disabled)
aha0 failed to probe on isa0
aic0: not probed (disabled)
atkbdc0: <Keyboard controller (i8042)> at port 0x64,0x60 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0065
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000
atkbd0: [GIANT-LOCKED]
psm0: not probed (disabled)
bt0: not probed (disabled)
cs0: not probed (disabled)
ed0: not probed (disabled)
fdc0: ic_type 90 part_id 80
fdc0: <Enhanced floppy controller> at port 0x3f0-0x3f5 irq 6 drq 2 on isa0
fdc0: ic_type 90 part_id 80
fdc0: [MPSAFE]
fdc0: [FAST]
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
fd1: <1200-KB 5.25" drive> on fdc0 drive 1
fe0: not probed (disabled)
ie0: not probed (disabled)
lnc0: not probed (disabled)
pcic0: not probed (disabled)
pcic1: not probed (disabled)
ppc0: parallel port found at 0x378
ppc0: using extended I/O port range
ppc0: <Parallel port> failed to probe at port 0x378-0x37f irq 7 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
sio0: irq maps: 0xe001 0xe011 0xe001 0xe001
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1: not probed (disabled)
sio2: not probed (disabled)
sio3: not probed (disabled)
sn0: not probed (disabled)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 07 80 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
EGA/VGA parameters to be used for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
vt0: not probed (disabled)
aha1: status reg test failed ff
aha1 failed to probe at port 0x334-0x337 on isa0
isa_probe_children: probing PnP devices
adv1: Invalid baseport of 0x220 specified. Nearest valid baseport is 0x230.
Failing probe.
unknown: <Audiotrix 3D-XG v1.0> failed to probe at port
0x370-0x371,0x330-0x331,0x388-0x38b,0x530-0x537,0x220-0x22f irq 5,10 drq 1,0 on
isa0
adv1: Invalid baseport of 0x201 specified. Nearest valid baseport is 0x210.
Failing probe.
unknown: <Audiotrix 3D-XG v1.0> failed to probe at port 0x201 on isa0
aha2: status reg test failed 0
adv1: Invalid baseport of 0x332 specified. Nearest valid baseport is 0x330.
Failing probe.
unknown: <Adaptec 1542/aha-1535> failed to probe at port 0x332-0x335 iomem
0xd0000-0xd3fff irq 11 drq 5 on isa0
adv1: Invalid baseport of 0x0 specified. Nearest valid baseport is 0x100.
Failing probe.
adv1: Invalid baseport of 0x40 specified. Nearest valid baseport is 0x100.
Failing probe.
adv1: Invalid baseport of 0x70 specified. Nearest valid baseport is 0x100.
Failing probe.
unknown: <PNP0303> can't assign resources (port)
unknown: <PNP0303> at port 0x60 on isa0
adv1: Invalid baseport of 0x61 specified. Nearest valid baseport is 0x100.
Failing probe.
unknown: <PNP0800> failed to probe at port 0x61 on isa0
adv1: Invalid baseport of 0xf0 specified. Nearest valid baseport is 0x100.
Failing probe.
adv1: Invalid baseport of 0x4d0 specified. Nearest valid baseport is 0x330.
Failing probe.
adv1: Invalid baseport of 0x208 specified. Nearest valid baseport is 0x210.
Failing probe.
unknown: <PNP0501> can't assign resources (port)
unknown: <PNP0501> at port 0x3f8-0x3ff on isa0
unknown: <PNP0700> can't assign resources (port)
unknown: <PNP0700> at port 0x3f2-0x3f5 on isa0
adv1: Invalid baseport of 0x378 specified. Nearest valid baseport is 0x330.
Failing probe.
ppc1: using extended I/O port range
unknown: <Standard parallel printer port> failed to probe at port 0x378-0x37f
irq 7 on isa0
Device configuration finished.
procfs registered
Timecounter "TSC" frequency 232671718 Hz quality -100
Timecounters tick every 10.000 msec
lo0: bpf attached
ata0-master: pio=0x0c wdma=0x22 udma=0x42 cable=80pin
ata0-master: setting PIO4 on Intel PIIX3 chip
ata0-master: setting WDMA2 on Intel PIIX3 chip
ad0: <WDC AC420400D/J58OA30K> ATA-4 disk at ata0-master
ad0: 19470MB (39876480 sectors), 39560 C, 16 H, 63 S, 512 B
ad0: 16 secs/int, 1 depth queue, WDMA2
ar: FreeBSD check1 failed
ata1-master: pio=0x0c wdma=0x22 udma=0x45 cable=80pin
ata1-master: setting PIO4 on Intel PIIX3 chip
ata1-master: setting WDMA2 on Intel PIIX3 chip
ad2: <WDC WD200BB-75DEA0/05.03E05> ATA-5 disk at ata1-master
ad2: 19073MB (39062500 sectors), 38752 C, 16 H, 63 S, 512 B
ad2: 16 secs/int, 1 depth queue, WDMA2
ar: FreeBSD check1 failed
Waiting 15 seconds for SCSI devices to settle
GEOM: new disk ad0
GEOM: new disk ad2
[0] f:80 typ:6 s(CHS):0/1/1 e(CHS):126/254/63 s:63 l:2040192
[1] f:00 typ:167 s(CHS):127/0/1 e(CHS):387/254/63 s:2040255 l:4192965
[2] f:00 typ:28 s(CHS):388/0/1 e(CHS):1023/254/63 s:6233220 l:33640110
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure ad0s1, start 32256 length 1044578304 end 1044610559
GEOM: Configure ad0s2, start 1044610560 length 2146798080 end 3191408639
GEOM: Configure ad0s3, start 3191408640 length 17223736320 end 20415144959
[0] f:00 typ:147 s(CHS):0/1/1 e(CHS):12/254/63 s:63 l:208782
[1] f:00 typ:6 s(CHS):13/0/1 e(CHS):272/254/63 s:208845 l:4176900
[2] f:00 typ:146 s(CHS):273/0/1 e(CHS):402/254/63 s:4385745 l:2088450
[3] f:00 typ:5 s(CHS):403/0/1 e(CHS):1023/254/63 s:6474195 l:32579820
GEOM: Configure ad2s1, start 32256 length 106896384 end 106928639
GEOM: Configure ad2s2, start 106928640 length 2138572800 end 2245501439
GEOM: Configure ad2s3, start 2245501440 length 1069286400 end 3314787839
GEOM: Configure ad2s4, start 3314787840 length 16680867840 end 19995655679
MBREXT Slice 5 on ad2s4:
[0] f:00 typ:131 s(CHS):403/1/1 e(CHS):1023/254/63 s:63 l:20482812
[1] f:00 typ:5 s(CHS):1023/254/63 e(CHS):1023/254/63 s:20482875 l:12096945
GEOM: Configure ad2s5, start 32256 length 10487199744 end 10487231999
MBREXT Slice 6 on ad2s4:
[0] f:00 typ:131 s(CHS):1023/254/63 e(CHS):1023/254/63 s:63 l:12096882
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure ad2s6, start 10487264256 length 6193603584 end 16680867839
(probe3:dpt0:0:3:0): error 22
(probe3:dpt0:0:3:0): Unretryable Error
pass0 at dpt0 bus 0 target 0 lun 0
pass0: <SEAGATE ST318417W 0105> Fixed Direct Access SCSI-3 device
pass0: Serial Number 3FA0A0X300007221AV1L
pass0: Tagged Queueing Enabled
pass1 at dpt0 bus 0 target 1 lun 0
pass1: <SEAGATE ST36530W 1206> Fixed Direct Access SCSI-2 device
pass1: Serial Number AYF30763
pass1: Tagged Queueing Enabled
pass2 at dpt0 bus 0 target 3 lun 0
pass2: <PLEXTOR CD-ROM PX-32CS 1.01> Removable CD-ROM SCSI-2 device
(cd0:dpt0:0:3:0): error 6
(cd0:dpt0:0:3:0): Unretryable Error
cd0 at dpt0 bus 0 target 3 lun 0
cd0: <PLEXTOR CD-ROM PX-32CS 1.01> Removable CD-ROM SCSI-2 device
cd0: Attempt to query device size failed: NOT READY, Medium not present
da0 at dpt0 bus 0 target 0 lun 0
da0: <SEAGATE ST318417W 0105> Fixed Direct Access SCSI-3 device
da0: Serial Number 3FA0A0X300007221AV1L
da0: Tagged Queueing Enabled
da0: 17547MB (35937405 512 byte sectors: 255H 63S/T 2237C)
da1 at dpt0 bus 0 target 1 lun 0
da1: <SEAGATE ST36530W 1206> Fixed Direct Access SCSI-2 device
da1: Serial Number AYF30763
da1: Tagged Queueing Enabled
da1: 6208MB (12715408 512 byte sectors: 255H 63S/T 791C)
GEOM: new disk cd0
GEOM: new disk da0
GEOM: new disk da1
SMP: AP CPU #1 Launched!
cpu1 AP:
ID: 0x01000000 VER: 0x00030010 LDR: 0x02000000 DFR: 0x0fffffff
lint0: 0x00010700 lint1: 0x00010400 TPR: 0x00000000 SVR: 0x000001ff
ioapic0: routing intpin 1 (ISA IRQ 1) to cluster 0
ioapic0: routing intpin 4 (ISA IRQ 4) to cluster 0
ioapic0: routing intpin 6 (ISA IRQ 6) to cluster 0
ioapic0: routing intpin 8 (ISA IRQ 8) to cluster 0
ioapic0: routing intpin 13 (ISA IRQ 13) to cluster 0
ioapic0: routing intpin 14 (ISA IRQ 14) to cluster 0
ioapic0: routing intpin 15 (ISA IRQ 15) to cluster 0
ioapic0: routing intpin 16 (ISA IRQ 12) to cluster 0
ioapic0: routing intpin 17 (ISA IRQ 3) to cluster 0
(cd0:dpt0:0:3:0): error 6
(cd0:dpt0:0:3:0): Unretryable Error
(cd0:dpt0:0:3:0): error 6
(cd0:dpt0:0:3:0): Unretryable Error
(cd0:dpt0:0:3:0): error 6
(cd0:dpt0:0:3:0): Unretryable Error
(cd0:dpt0:0:3:0): error 6
(cd0:dpt0:0:3:0): Unretryable Error
(cd0:dpt0:0:3:0): error 6
(cd0:dpt0:0:3:0): Unretryable Error
(cd0:dpt0:0:3:0): error 6
(cd0:dpt0:0:3:0): Unretryable Error
[0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:35937342
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure da0s1, start 32256 length 18399919104 end 18399951359
[0] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure da0s1a, start 0 length 524288000 end 524287999
GEOM: Configure da0s1b, start 3745513472 length 1073741824 end 4819255295
GEOM: Configure da0s1c, start 0 length 18399919104 end 18399919103
GEOM: Configure da0s1d, start 524288000 length 3221225472 end 3745513471
GEOM: Configure da0s1e, start 4819255296 length 13580663808 end 18399919103
Mounting root from ufs:/dev/da0s1a
start_init: trying /sbin/init
ioapic0: routing intpin 10 (ISA IRQ 10) to cluster 0
ioapic0: routing intpin 5 (ISA IRQ 5) to cluster 0
Linux ELF exec handler installed
xl0: transmission error: 90
xl0: tx underrun, increasing tx start threshold to 120 bytes
_______________________________________________ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to "[EMAIL PROTECTED]"
