Thanks so much for the help in getting my V.Everything Internal
Modem working!
I wanted to document the steps that I took so that in the future if
Anyone else has this problem, hopefully this can point them in the
right
direction.
To start with, I used the 'pnpinfo' command, and
this got my hopes up that it was possible to get this modem working
eventually. The output of pnpinfo was as follows:
Checking for Plug-n-Play devices...
Card assigned CSN #1
Vendor ID USR0101 (0x01017256), Serial Number 0xacb0bb15
PnP Version 1.0, Vendor Version 0
Device Description: USRobotics Courier V.Everything
Logical Device ID: USR0009 0x09007256 #0
TAG Start DF
Good Configuration
FIXED I/O base address 0x2f8 length 0x8
IRQ: 3 4 5 7 9 - only one type (true/edge)
TAG Start DF
Acceptable Configuration
FIXED I/O base address 0x3f8 length 0x8
IRQ: 3 4 5 7 9 - only one type (true/edge)
TAG Start DF
Acceptable Configuration
FIXED I/O base address 0x3e8 length 0x8
IRQ: 3 4 5 7 9 - only one type (true/edge)
TAG Start DF
Acceptable Configuration
FIXED I/O base address 0x2e8 length 0x8
IRQ: 3 4 5 7 9 - only one type (true/edge)
TAG End DF
End Tag
Successfully got 16 resources, 1 logical fdevs
-- card select # 0x0001
CSN USR0101 (0x01017256), Serial Number 0xacb0bb15
Logical device #0
IO: 0x03e8 0x03e8 0x03e8 0x03e8 0x03e8 0x03e8 0x03e8 0x03e8
IRQ 5 0
DMA 4 4
IO range check 0x00 activate 0x01
The part that is interesting to us is this:
Card assigned CSN #1
Vendor ID USR0101 (0x01017256), Serial Number 0xacb0bb15
PnP Version 1.0, Vendor Version 0
Device Description: USRobotics Courier V.Everything
Logical Device ID: USR0009 0x09007256 #0
According to the documentation in the file:
/usr/share/doc/en/books/faq/book.txt
we need to add the part after the USR0101, (which is 0x01017256), to
the
file /usr/src/sys/isa/sio.c, recompile our kernel, and voila, it
should be
found.
However, this didn't work for me right away. I played around with
it, and
found that it was the number on the line labeled 'Logical Device ID'
that I
needed to add to the sio.c file.
After trying that, I recompiled the kernel and it worked like a
charm.
-----Original Message-----
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] Behalf Of Сергей
Куликов
Sent: Friday, November 07, 2003 12:10 PM
To: [EMAIL PROTECTED]
Subject: Can't make the system see my modem! Please help!!!
I have ELINE 576-PS (PCTel PCT789T-A Chipset) internal modem device
and need to
set it up under FreeBSD 4.7 box. GENERIC kernel says when booting:
pci0: <unknown card> (vendor=0x134d, dev=0x7897) at 11.0 irq 9
As you see my modem is unknown for GENERIC kernel. I saw
/boot/defaults/loader.conf and found no line corresponding to that
particular modem at all. What should I do to make the system see the
device and interact with one.
Any help would be apreciated.
--
Best regards,
Сергей mailto:[EMAIL PROTECTED]
_______________________________________________
[EMAIL PROTECTED] mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-questions
To unsubscribe, send any mail to
"[EMAIL PROTECTED]"
_______________________________________________
[EMAIL PROTECTED] mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-questions
To unsubscribe, send any mail to "[EMAIL PROTECTED]"
