On Tuesday 28 August 2007 13:48, [EMAIL PROTECTED] wrote: > What does configuring the modem in bridging mode means? > > ====================================================================== > ========================= ppp.conf ============================= > ====================================================================== > > default: > set device PPPoE:rl0 > set MTU 1492 > set MRU 1492 > set crtscts off > set speed sync > #set timeout 0 > #set redial 0 0 > enable lqr > #disable deflate > #disable pred1 > #disable vjcomp > #disable acfcomp > #disable protocomp > set log Phase tun LCP IPCP CCP Warning Error Alert > set ifaddr 10.0.0.1/0 10.0.0.2/0 255.255.255.255 0.0.0.0 > add default HISADDR > #enable proxy > #nat enable yes > #nat log yes > #nat same_ports yes > #nat unregistered_only yes > #nat deny_incoming yes > dsl: > set login > set authname [EMAIL PROTECTED] > set authkey asd12345 >
This configuration file has several irrelevant settings. Try the one below, it's from here: /usr/share/examples/ppp/ppp.conf.sample I just added "set authname" & "set authkey", changed the NIC's name and removed the service name. pppoe: set authname "your_username" set authkey "your_password" set device PPPoE:rl0 enable lqr echo set cd 5 set dial set login set redial 0 0 [snip] > ====================================================================== > ======================= sysctl.conf ============================ > ====================================================================== > > net.link.ether.bridge.config=rl0:0,ed0:0 > net.link.ether.bridge.ipfw=1 > net.link.ether.bridge.enable=1 > net.inet.ip.forwarding=1 > This has nothing to do with modem bridging mode. This bridges your two ethernet segments. Disable it if that's not what you want. > ====================================================================== > ========================= ppp.log ============================== > ====================================================================== > > Aug 28 03:58:21 cp ppp[786]: Phase: Using interface: tun0 > Aug 28 03:58:21 cp ppp[786]: Phase: deflink: Created in closed state > Aug 28 03:58:21 cp ppp[786]: tun0: Phase: PPP Started (interactive > mode). Aug 28 03:58:22 cp ppp[801]: Phase: Using interface: tun1 > Aug 28 03:58:22 cp ppp[801]: Phase: deflink: Created in closed state > Aug 28 03:58:22 cp ppp[802]: tun1: Phase: PPP Started (auto mode). > Aug 28 03:59:40 cp ppp[786]: tun0: Phase: bundle: Establish > Aug 28 03:59:40 cp ppp[786]: tun0: Phase: deflink: closed -> opening > Aug 28 03:59:40 cp ppp[786]: tun0: Phase: deflink: Connected! > Aug 28 03:59:40 cp ppp[786]: tun0: Phase: deflink: opening -> dial > Aug 28 03:59:40 cp ppp[786]: tun0: Phase: deflink: dial -> carrier > Aug 28 03:59:45 cp ppp[786]: tun0: Phase: deflink: Disconnected! > Aug 28 03:59:45 cp ppp[786]: tun0: Phase: deflink: carrier -> hangup > Aug 28 03:59:45 cp ppp[786]: tun0: Phase: deflink: Connect time: 5 secs: > 0 octets in, 0 octets out ^^^^^^^^^^^^^^^^^^ Zero octets in and zero octets out. Is your modem in bridging mode? It may be called rfc1483. Enable it. check what goes on with tcpdump: root:0:/# tcpdump -nli rl0 tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on rl0, link-type EN10MB (Ethernet), capture size 96 bytes 14:34:54.863275 PPPoE PADI [Host-Uniq 0xC0656EC3] [Service-Name] 14:34:56.862997 PPPoE PADI [Host-Uniq 0xC0656EC3] [Service-Name] 14:34:59.969272 PPPoE PADI [Host-Uniq 0xC00CFAC3] [Service-Name] This is not what you should see, you should see PADO and the rest. If that's what you see, your modem is probably not in bridging mode. [snip] Hope this helps Nikos _______________________________________________ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to "[EMAIL PROTECTED]"
