Hi list, I've made some progress.. my rc.conf looks like this:
cloned_interfaces="vlan100 vlan200 vlan254" ifconfig_vr0="up" ifconfig_vlan100="inet 192.168.100.1 netmask 255.255.255.0 vlan 100 vlandev vr0" ifconfig_vlan200="inet 192.168.200.1 netmask 255.255.255.0 vlan 200 vlandev vr0" ifconfig_vlan254="inet 10.254.254.252 netmask 255.255.255.0 vlan 254 vlandev vr0" defaultrouter="10.254.254.254" Switch config has stayed the same, what I want to do now is do a one-liner on the vr0 interface so I can bring it up and set the speed duplex to 100/full. When I do: ifconfig_vr0="up media 100baseTX mediaopt full-duplex" It doesnt seem to work, any ideas what I'm doing wrong? Cheers, Will On 27/07/06, James Snow <[EMAIL PROTECTED]> wrote:
Will, In your ifconfig_vr0, line, you have a typo. The 'f' is missing from full-duplex. Possibly just a copy & paste gaffe, and I doubt it's the cause of your problem anyway. The vr driver isn't listed in if_vlan(4). It may be one of the ones that doesn't work, or doesn't work very well. Also, if connected to a trunking port, I'm not sure what happens to frames that leave without an 802.1Q header. Frames leaving via vr0 would be untagged and I think dropped by the switch. You may need to drop 10.25.254.252 from vr0 and put it on a fourth VLAN interface. But don't quote me on this. Hope this helps. -Snow On Thu, Jul 27, 2006 at 02:07:14PM +0100, William wrote: > Hi list, > > I'm trying to get a FreeBSD 5.3-RELEASE (running GENERIC kernel) to do > vlan tagging. > > I want to have several 'vlan interfaces' that can talk to their local > subnet and also use a default route. > > On the switch side of things I'm using a Cisco 3550 runing layer3 > code, I've had this working before with a em driver (on another box) > but my setup was a little different then so I'm pretty sure the switch > isnt at fault? > > My rc.conf looks like: > > cloned_interfaces="vlan100 vlan200 vlan233" > ifconfig_vr0="up" > ifconfig_vlan100="inet 192.168.100.1 netmask 255.255.255.0 vlan 100 vlandev > vr0" > ifconfig_vlan200="inet 192.168.200.1 netmask 255.255.255.0 vlan 200 vlandev > vr0" > ifconfig_vlan233="inet 10.233.233.1 netmask 255.255.255.0 vlan 233 vlandev > vr0" > ifconfig_vr0="inet 10.254.254.252 netmask 255.255.255.0 media > 100baseTX mediaopt ull-duplex" > defaultrouter="10.254.254.254" > > and my switch config looks like this: > > interface FastEthernet0/12 > switchport access vlan 254 > switchport trunk encapsulation dot1q > switchport trunk allowed vlan 100,200,233 > switchport mode trunk > logging event trunk-status > duplex full > speed 100 > end > > I'm getting to the point that the vlan interfaces (100,200,233) can > talk to machines on their subnet but I cannot seem to ping anything on > the 10.254.254.0/24 subnet (ip address applied to vr0 interface) or > anythnig via the default route. > > If anyone can assist me I'd appreciate it, please contact me off list > as I am not subscribed to -questions. > > Cheers, > > Will > _______________________________________________ > freebsd-questions@freebsd.org mailing list > http://lists.freebsd.org/mailman/listinfo/freebsd-questions > To unsubscribe, send any mail to "[EMAIL PROTECTED]"
_______________________________________________ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to "[EMAIL PROTECTED]"
