Derrick Ryalls wrote:
On 7/21/06, Rich Demanowski <[EMAIL PROTECTED]> wrote:
I just dropped a SoundBlaster Live! card into my box, and have followed
the directions in the handbook and the man pages.
The following lines are in the compiled kernel:
device sound
device snd_emu10k1
I don't get the pcm0 lines that section 7.2.2 in the manual talks
about. cat /dev/sndstat returns:
FreeBSD Audio Driver (newpcm)
Installed devices:
and nothing else.
kldload snd_emu10k1 yields no output whatsoever. When followed by cat
/dev/sndstat it produces the same outputs as above.
kld_load snd_driver yields:
ppc0: parallel port not found.
sio1: configured irq 3 not in bitmap of probed irqs 0x20
sio1: port may not be enabled
ppc0: parallel port not found.
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
ppc0: parallel port not found.
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
ppc0: parallel port not found.
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
ppc0: parallel port not found.
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
ppc0: parallel port not found.
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
ppc0: parallel port not found.
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
I recompiled with the sound and emu10k1 drivers commented out, and the
kldload and cat /dev/sndstat commands still yield the same.
I need to get sound enabled on this box, so I can do some online
training provided through streaming video. Please, please, please tell
me I don't have to break down and install wankers on this thing ...
I would try this:
kldload snd_driver
then cat /dev/sndstat to see if perhaps a different driver is needed.
Also, you shouldn't need to recompile, just add the driver line to
/boot/loader.conf as described in the handbook.
Could this be (part of?) the problem? --
in dmesg:
.
.
.
isab0: <PCI-ISA bridge> at device 10.0 on pci0
.
.
.
pci3: <multimedia, audio> at device 10.0 (no driver attached)
I've re-compiled my kernel yet again to remove the sio device, since
this thing has no 8250 or 16[45]50 serial ports on it, which got rid of
the error messages in dmesg I was seeing about the port not being
enabled and the IRQ not mapping.
It also has no parallel port on it -- can I remove the ppc, ppbus, lpt,
plip, and ppi devices without breaking anything else?
The only peripheral ports this thing has on it are USB2.
I'm pretty much stuck with a custom kernel on this machine, since the
wireless network I'm on requires WEP, and the wlan_wep module would need
to be loaded by hand if I went with the generic kernel and module
loading ... which would also mean hand-starting dhcpclient and ifconfig,
since both will fail at boot-time without wlan_wep. All the wireless
stuff works just fine with ath, ath_hal, ath_rate_sample, wlan, and
wlan_wep compiled into the kernel.
The only thing I can't seem to get working is this blasted sound card.
I wouldn't even worry about it if I didn't have to do this stupid flash
based video training crap (why can't they just send me TFM so I can R
it?!?). *sigh*
_______________________________________________
freebsd-questions@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-questions
To unsubscribe, send any mail to "[EMAIL PROTECTED]"
