On Thu, Apr 13, 2006 at 11:01:51PM +0900, SungGON Yi. wrote: > I am using 6.x on Tyan S2885ANRF board and add one more NIC. > Device names are bge0 (board lan) and bge1 (additional NIC). > > These worked well on FreeBSD 6.0-amd64 stable. > But when I updated to 6.1-PRERELEASE version, I had below messages and bge0 > did not work. > bge1 worked well as before. > > -------------------------------- > bge0: watchdog timeout -- resetting > -------------------------------- > > I am using 6.0-RELEASE now. > > -------------------------------- > bge0: <Broadcom BCM5701 Gigabit Ethernet, ASIC rev. 0x105> mem > 0xfc6f0000-0xfc6fffff irq 27 at device 8.0 on pci2 > miibus0: <MII bus> on bge0 > brgphy0: <BCM5701 10/100/1000baseTX PHY> on miibus0 > brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, > 1000baseTX-FDX, auto > bge0: Ethernet address: 00:04:76:f3:e8:c9 > bge1: <Broadcom BCM5703 Gigabit Ethernet, ASIC rev. 0x1002> mem > 0xfc6e0000-0xfc6effff irq 24 at device 9.0 on pci2 > miibus1: <MII bus> on bge1 > brgphy1: <BCM5703 10/100/1000baseTX PHY> on miibus1 > brgphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, > 1000baseTX-FDX, auto > bge1: Ethernet address: 00:e0:81:27:a0:f6 > ----------------------------------- > > -------------------------------------------------------------------------------------------------------------------------------- > $ ifconfig > bge0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500 > options=1b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING> > inet6 fe80::204:76ff:fef3:e8c9%bge0 prefixlen 64 scopeid 0x1 > inet xxx.xxx.xxx.xxx netmask 0xffffff00 broadcast xxx.xxx.xxx.xxx > ether 00:04:76:f3:e8:c9 > media: Ethernet autoselect (100baseTX <full-duplex>) > status: active > bge1: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500 > options=1b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING> > inet6 fe80::2e0:81ff:fe27:a0f6%bge1 prefixlen 64 scopeid 0x2 > inet 192.168.24.106 netmask 0xffffff00 broadcast 192.168.24.255 > ether 00:e0:81:27:a0:f6 > media: Ethernet autoselect (1000baseTX <full-duplex>) > status: active > lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384 > inet6 ::1 prefixlen 128 > inet6 fe80::1%lo0 prefixlen 64 scopeid 0x3 > inet 127.0.0.1 netmask 0xff000000 > pfsync0: flags=0<> mtu 2020 > pflog0: flags=0<> mtu 33160 > ------------------------------------ > > SungGON Yi. > [EMAIL PROTECTED] >
> _______________________________________________ > freebsd-stable@freebsd.org mailing list > http://lists.freebsd.org/mailman/listinfo/freebsd-stable > To unsubscribe, send any mail to "[EMAIL PROTECTED]" I've seen one report about broken onboard bcm5701 asic rev 0x105. Unfortunatly i dont have such motherboard to play with. I have PCI nic with same chip/revision which works fine. Do you mind of doing binary search on if_bge.c (rev. 1.95 - 1.118) ? -- Oleg.
pgp1f5M5O5XGe.pgp
Description: PGP signature
