Brian John <[EMAIL PROTECTED]> writes: > Lowell Gilbert wrote: > > >Brian John <[EMAIL PROTECTED]> writes: > > > > > >>Parv wrote: > >> > >> > >>>in message > >>><[EMAIL PROTECTED] > >>> > >>> > >>>>, wrote Brian John thusly... > >>>> > >>>>I just got a 128MB USB flash drive. When I plug it in in FreeBSD, > >>>>the box promptly reboots! What would cause this? > >>>> > >>>> > >>>I don't know the cause. > >>> > >>>Have you tried booting FreeBSD from power-off state w/ the flash > >>>drive already inserted? That may solve your booting problem, but > >>>will not make use of the drive any easier. > >>> > >>>Which version if FreeBSD are you using? Which of the [ueo]hci > >>>drivers come up in dmesg(8) on instertion of the USB drive? > >>> > >>> > >>> - Parv > >>> > >>> > >>> > >>Ok, I tried booting up with the drive installed. If I leave it > >>installed while it is booting up, it eventually reboots. However, I > >>was able to unplug it during boot and look at dmesg. It says this > >>over and over again: > >> > >>umass0: vendor 0x10d6 USB 2.0(FS) FLASH DISK, rev 1.10/1.00, addr 2 > >>da0 at umass-sim0 bus 0 target 0 lun 0 > >>da0: <USB2.0 (FS) FLASH DISK 1.00> Removable Direct Access SCSI-0 device > >>da0: 1.000MB/s transfers > >>da0: 119MB (245473 512 byte sectors: 64H 32S/T 119C) > >>umass0: BBB reset failed, STALLED > >>umass0: BBB bulk-in clear stall failed, STALLED > >>umass0: BBB bulk-out clear stall failed, STALLED > >>(da0:umass-sim0:0:0:0): Synchronize cache failed, status == 0x4, scsi > >>status == 0x0 > >>umass0: BBB reset failed, STALLED > >>umass0: BBB bulk-in clear stall failed, STALLED > >>umass0: BBB bulk-out clear stall failed, STALLED > >>umass0: BBB reset failed, STALLED > >>umass0: BBB bulk-in clear stall failed, STALLED > >>umass0: BBB bulk-out clear stall failed, STALLED > >>umass0: BBB reset failed, STALLED > >>umass0: BBB bulk-in clear stall failed, STALLED > >>umass0: BBB bulk-out clear stall failed, STALLED > >>umass0: BBB reset failed, STALLED > >>umass0: BBB bulk-in clear stall failed, STALLED > >>umass0: BBB bulk-out clear stall failed, STALLED > >>umass0: BBB reset failed, STALLED > >>umass0: BBB bulk-in clear stall failed, STALLED > >>umass0: BBB bulk-out clear stall failed, STALLED > >>umass0: at uhub2 port 1 (addr 2) disconnected > >>(da0:umass-sim0:0:0:0): lost device > >>(da0:umass-sim0:0:0:0): removing device entry > >>Opened disk da0 -> 5 > >>umass0: detached > >> > >>I am running FreeBSD 5.4. Does this shed some light on the problem? > >> > > > > Only a little. Do you have udbp(4) in your kernel? Can you try > > booting 6.0 with the flash unit plugged in and see if it > >still has problems? > > > > > I could try it, but I don't want to have to roll 6.0 back to 5.4 > afterward if it doesn't work. Upgrading to 6.0 is a major change and > I only have 1 PC. I am still kind of a novice, how easy is it to > upgrade to 6.0 and how stable is it?
You don't need to install it to your hard drive; just boot the install disk and see if it gets all of the way through the kernel loading. > I see that I have the line with > udbp commented out in my kernel config. Should I rebuild with it > uncommented? > > #device udbp # USB Double Bulk Pipe devices You could try that. I was meaning to read up on that USB feature, but unfortunately I can't find the specs for it at the moment. I don't actually know whether it might be relevant. _______________________________________________ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to "[EMAIL PROTECTED]"
