With FreeSBIE 1.1 (based on FreeBSD 5.3), it says: acd0: TIMEOUT - READ_BIG retrying (2 retries left) acd0: TIMEOUT - READ_BIG timed out Then it stop/freezes. If I press the power button, it says "acpi: suspend request ignored (not ready yet)."
Thanks. On 4/23/05, Laurent Debacker <[EMAIL PROTECTED]> wrote: > I tried 5.4-RC3 with no ACPI, safe mode, and DEBUG mode, without > success. DEBUG doesn't repport anything. > > 5.3 also crashes in safe mode, and no ACPI, freezes after "pci0: <PCI > bus> on pcib0". > > dmesg on 4.11 reports: > ohci0: <AcerLabs M5237 (Aladdin-V) USB controller> mem > 0xf7eff000-0xf7efffff irq 11 at device 2.0 on pci0. > You can see full report below. > > Thank you for your help ;) > Laurent. > > Here are drivers loaded by 4.11 as reported by dmesg: > md0: Preloaded image </mfsroot> 4423680 bytes at 0xc03edc14 > md1: Malloc disk > Using $PIR table, 9 entries at 0xc00f01d0 > npx0: <math processor> on motherboard > npx0: INT 16 interface > pcib0: <Host to PCI bridge> on motherboard > pci0: <PCI bus> on pcib0 > pcib1: <Acerlabs M5247 PCI-PCI(AGP Supported) bridge> at device 1.0 on pci0 > pci1: <PCI bus> on pcib1 > pci1: <Trident model 8820 VGA-compatible display device> at 0.0 irq 11 > ohci0: <AcerLabs M5237 (Aladdin-V) USB controller> mem > 0xf7eff000-0xf7efffff irq 11 at device 2.0 on pci0 > usb0: OHCI version 1.0, legacy support > usb0: SMM does not respond, resetting > usb0: <AcerLabs M5237 (Aladdin-V) USB controller> on ohci0 > usb0: USB revision 1.0 > uhub0: AcerLabs OHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub0: 4 ports with 4 removable, self powered > atapci0: <AcerLabs Aladin ATA66 controller> port 0xeff0-0xefff at > device 4.0 on pci0 > ata0: at 0x1f0 irq 14 on atapci0 > ata1: at 0x170 irq 15 on atapci0 > pci0: <unknown card> (vendor=0x10b9, dev=0x5451) at 6.0 > isab0: <AcerLabs M1533 portable PCI-ISA bridge> at device 7.0 on pci0 > isa0: <ISA bus> on isab0 > chip1: <AcerLabs M15x3 Power Management Unit> at device 8.0 on pci0 > fxp0: <Intel 82559 Pro/100 Ethernet> port 0xeec0-0xeeff mem > 0xf7d00000-0xf7dfffff,0xf7efe000-0xf7efefff irq 11 at device 10.0 on > pci0 > fxp0: Ethernet address 00:00:39:a7:a0:b4 > inphy0: <i82555 10/100 media interface> on miibus0 > inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto > pci_cfgintr_linked: linked (3) to hard-routed irq 11 > pci_cfgintr: 0:16 INTA routed to irq11 > pcic0: <TI PCI-1410 PCI-CardBus Bridge> irq 11 at device 16.0 on pci0 > pcic0: PCI Memory allocated: 0x88000000 > pcic0: TI12XX PCI Config Reg: [pwr save][pci only] > pccard0: <PC Card 16-bit bus (classic)> on pcic0 > pci_cfgintr_linked: linked (1) to hard-routed irq 11 > pci_cfgintr: 0:17 INTA routed to irq11 > pcic1: <Toshiba ToPIC100 PCI-CardBus Bridge> irq 11 at device 17.0 on pci0 > pcic1: PCI Memory allocated: 0x88001000 > pccard1: <PC Card 16-bit bus (classic)> on pcic1 > pci_cfgintr_linked: linked (2) to hard-routed irq 11 > pci_cfgintr: 0:17 INTB routed to irq11 > pcic2: <Toshiba ToPIC100 PCI-CardBus Bridge> irq 11 at device 17.1 on pci0 > pcic2: PCI Memory allocated: 0x88002000 > pccard2: <PC Card 16-bit bus (classic)> on pcic2 > pci0: <unknown card> (vendor=0x1179, dev=0x0805) at 18.0 > orm0: <Option ROMs> at iomem 0xc0000-0xcbfff,0xe0000-0xeffff on isa0 > pmtimer0 on isa0 > fdc0: ready for input in output > fdc0: cmd 3 failed at out byte 1 of 3 > atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 > atkbd0: <AT Keyboard> flags 0x1 irq1 on atkbdc0 > kbd0 at atkbd0 > psm0: <PS/2 Mouse> irq 12 on atkbdc0 > psm0: model IntelliMouse, device ID 3 > vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 > sc0: <System console> at flags 0x100 on isa0 > sc0: VGA <16 virtual consoles, flags=0x300> > sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 > sio0: type 16550A > sio1: configured irq 3 not in bitmap of probed irqs 0 > ppc0: parallel port not found. > pccard: card inserted, slot0 > pccard: card removed, slot0 > ad0: 16077MB <IC25N020ATCS04-0> [38760/16/63] at ata0-master UDMA66 > acd0: DVD-ROM <TOSHIBA DVD-ROM SD-C2502> at ata1-master PIO4 > > On 4/23/05, Kevin Kinsey <[EMAIL PROTECTED]> wrote: > > Laurent Debacker wrote: > > > > >Hello, > > > > > >Both FreeBSD 5.3 and 5.4-RC3 freeze during the boot of the kernel. It > > >detects my CPU, RAM, some ACPI stuffs.. I noticed > > >pci1: <display, VGA> at device 0.0 (no driver attached). > > >I don't know if it's ok. > > >At the end, it says ohci0: [GIANT-LOCKED] > > >then usb0: OHCI version 1.0, legacy support, > > >then nothing. > > > > > >FreeBSD 4.11 boots well. However I don't want FreeBSD 4.11 ;) > > > > > >Any idea? > > > > > >Thank you, > > >Laurent Debacker. > > > > > > > > > > What does the 4.11 dmesg say about the ochi device? > > > > Can you boot safe mode on 5.X? Have you tried booting > > with ACPI disabled? > > > > HTH, > > > > KDK > > > > > _______________________________________________ freebsd-questions@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to "[EMAIL PROTECTED]"
