Just cant seem to figure out how to correct this neg. time issue with my
server.
calcru: negative time of 25967268 usec for pid 139 (setiathome)
I have included all that I could think of to give a clue to what is
going on
any help would be appreciated.
jessie
Copyright (c) 1992-2002 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights
reserved.
FreeBSD 4.6-RELEASE #7: Tue Jul 16 22:27:52 GMT 2002
[EMAIL PROTECTED]:/usr/src/sys/compile/Env1
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium III/Pentium III Xeon/Celeron (795.90-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x683 Stepping = 3
Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory = 536805376 (524224K bytes)
avail memory = 517046272 (504928K bytes)
Programming 24 pins in IOAPIC #0
IOAPIC #0 intpin 2 -> irq 0
FreeBSD/SMP: Multiprocessor motherboard
cpu0 (BSP): apic id: 1, version: 0x00040011, at 0xfee00000
cpu1 (AP): apic id: 0, version: 0x00040011, at 0xfee00000
io0 (APIC): apic id: 2, version: 0x00170011, at 0xfec00000
Preloaded elf kernel "kernel" at 0xc051f000.
Pentium Pro MTRR support enabled
md0: Malloc disk
Using $PIR table, 12 entries at 0xc00fdf00
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Intel 82443GX host to PCI bridge> on motherboard
IOAPIC #0 intpin 19 -> irq 2
IOAPIC #0 intpin 21 -> irq 9
pci0: <PCI bus> on pcib0
pcib2: <Intel 82443GX (440 GX) PCI-PCI (AGP) bridge> at device 1.0 on
pci0
pci1: <PCI bus> on pcib2
pcib3: <PCI to PCI bridge (vendor=1011 device=0023)> at device 15.0 on
pci1
IOAPIC #0 intpin 20 -> irq 10
IOAPIC #0 intpin 23 -> irq 11
pci2: <PCI bus> on pcib3
pcm0: <AudioPCI ES1373-8> port 0x3000-0x303f irq 10 at device 4.0 on
pci2
pci2: <Matrox MGA Millennium 2064W graphics accelerator> at 7.0 irq 11
ahc0: <Adaptec aic7896/97 Ultra2 SCSI adapter> port 0x2400-0x24ff mem
0xf4101000-0xf4101fff irq 2 at device 12.0 on pci0
aic7896/97: Ultra2 Wide Channel A, SCSI Id=7, 32/253 SCBs
ahc1: <Adaptec aic7896/97 Ultra2 SCSI adapter> port 0x2800-0x28ff mem
0xf4102000-0xf4102fff irq 2 at device 12.1 on pci0
aic7896/97: Ultra2 Wide Channel B, SCSI Id=7, 32/253 SCBs
fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0x2000-0x203f mem
0xf4000000-0xf40fffff,0xf4100000-0xf4100fff irq 9 at device 14.0 on pci0
fxp0: Ethernet address 00:d0:b7:89:da:18
inphy0: <i82555 10/100 media interface> on miibus0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
isab0: <Intel 82371AB PCI to ISA bridge> at device 18.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 ATA33 controller> port 0x2040-0x204f at device
18.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
uhci0: <Intel 82371AB/EB (PIIX4) USB controller> irq 9 at device 18.2 on
pci0
uhci0: Could not map ports
device_probe_and_attach: uhci0 attach returned 6
Timecounter "PIIX" frequency 3579545 Hz
chip1: <Intel 82371AB Power management controller> port 0x1040-0x104f at
device 18.3 on pci0
pci0: <Cirrus Logic GD5480 SVGA controller> at 20.0
pcib1: <Intel 82443GX host to AGP bridge> on motherboard
pci3: <PCI bus> on pcib1
orm0: <Option ROMs> at iomem
0xc0000-0xc7fff,0xc8000-0xcd7ff,0xcd800-0xcdfff on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on
isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model IntelliMouse, device ID 3
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on
isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
sio4: <U.S. Robotics 56K Voice INT> at port 0x3e8-0x3ef irq 5 on isa0
sio4: type 16550A
APIC_IO: Testing 8254 interrupt delivery
APIC_IO: routing 8254 via IOAPIC #0 intpin 2
SMP: AP CPU #1 Launched!
ad0: 19092MB <WDC WD200BB-60CVB0> [38792/16/63] at ata0-master UDMA33
acd0: CDROM <ASUS CD-S520/A> at ata1-master PIO4
acd1: CD-RW <IOMEGA ZIPCDINT1536> at ata1-slave PIO4
Waiting 15 seconds for SCSI devices to settle
sa0 at ahc1 bus 0 target 4 lun 0
sa0: <ARCHIVE Python 28388-XXX 5.72> Removable Sequential Access SCSI-2
device
sa0: 7.812MB/s transfers (7.812MHz, offset 15)
da1 at ahc1 bus 0 target 3 lun 0
da1: <SEAGATE ST34371W 0484> Fixed Direct Access SCSI-2 device
da1: 40.000MB/s transfers (20.000MHz, offset 15, 16bit), Tagged Queueing
Enabled
da1: 4148MB (8496884 512 byte sectors: 255H 63S/T 528C)
da0 at ahc1 bus 0 target 1 lun 0
da0: <SEAGATE ST32155W 0362> Fixed Direct Access SCSI-2 device
da0: 40.000MB/s transfers (20.000MHz, offset 15, 16bit), Tagged Queueing
Enabled
da0: 2049MB (4197405 512 byte sectors: 255H 63S/T 261C)
Mounting root from ufs:/dev/ad0s2a
calcru: negative time of 25967268 usec for pid 139 (setiathome)
-- sysinstall generated deltas -- # Sun Jun 16 12:31:31 2002
# Created: Sun Jun 16 12:31:31 2002
# Enable network daemons for user convenience.
# Please make all changes to this file, not to /etc/defaults/rc.conf.
# This file now contains just the overrides from /etc/defaults/rc.conf.
defaultrouter="192.168.1.1"
hostname="Envelope.floyd.net"
ifconfig_fxp0="inet 192.168.1.10 netmask 255.255.255.0"
kern_securelevel_enable="NO"
linux_enable="YES"
lpd_enable="YES"
nfs_reserved_port_only="YES"
sendmail_enable="YES"
sshd_enable="YES"
usbd_enable="YES"
moused_type="NO"
moused_enable="NO"
sysctl -w vfs.usermount=1
sysctl -w kern.timecounter.method=1
#
# GENERIC -- Generic kernel configuration file for FreeBSD/i386
#
# For more information on this file, please read the handbook section on
# Kernel Configuration Files:
#
# http://www.FreeBSD.org/handbook/kernelconfig-config.html
#
# The handbook is also available locally in /usr/share/doc/handbook
# if you've installed the doc distribution, otherwise always see the
# FreeBSD World Wide Web server (http://www.FreeBSD.org/) for the
# latest information.
#
# An exhaustive list of options and more detailed explanations of the
# device lines is also present in the ./LINT configuration file. If you
are
# in doubt as to the purpose or necessity of a line, check first in
LINT.
#
# $FreeBSD: src/sys/i386/conf/GENERIC,v 1.246.2.43 2002/05/23 17:04:01
obrien Exp $
machine i386
cpu I686_CPU
ident ENV1
maxusers 0
#makeoptions DEBUG=-g #Build kernel with gdb(1) debug
symbols
options MATH_EMULATE #Support for x87 emulation
options INET #InterNETworking
options INET6 #IPv6 communications protocols
options FFS #Berkeley Fast Filesystem
options FFS_ROOT #FFS usable as root device [keep
this!]
options SOFTUPDATES #Enable FFS soft updates support
options UFS_DIRHASH #Improve performance on big
directories
options MFS #Memory Filesystem
options MD_ROOT #MD is a potential root device
options NFS #Network Filesystem
options NFS_ROOT #NFS usable as root device, NFS
required
options MSDOSFS #MSDOS Filesystem
options CD9660 #ISO 9660 Filesystem
options CD9660_ROOT #CD-ROM usable as root, CD9660
required
options PROCFS #Process filesystem
options COMPAT_43 #Compatible with BSD 4.3 [KEEP
THIS!]
options SCSI_DELAY=15000 #Delay (in ms) before probing
SCSI
options UCONSOLE #Allow users to grab the console
options USERCONFIG #boot -c editor
options VISUAL_USERCONFIG #visual boot -c editor
options KTRACE #ktrace(1) support
options SYSVSHM #SYSV-style shared memory
options SYSVMSG #SYSV-style message queues
options SYSVSEM #SYSV-style semaphores
options P1003_1B #Posix P1003_1B real-time
extensions
options _KPOSIX_PRIORITY_SCHEDULING
options ICMP_BANDLIM #Rate limit bad replies
options KBD_INSTALL_CDEV # install a CDEV entry in /dev
options USER_LDT # required for wine
options NTIMECOUNTER=20 # recomended to correct calcru
error
# To make an SMP kernel, the next two are needed
options SMP # Symmetric MultiProcessor
Kernel
options APIC_IO # Symmetric (APIC) I/O
device isa
device eisa
device pci
# Floppy drives
device fdc0 at isa? port IO_FD1 irq 6 drq 2
device fd0 at fdc0 drive 0
# ATA and ATAPI devices
device ata0 at isa? port IO_WD1 irq 14
device ata1 at isa? port IO_WD2 irq 15
device ata
device atadisk # ATA disk drives
device atapicd # ATAPI CDROM drives
device atapifd # ATAPI floppy drives
device atapist # ATAPI tape drives
options ATA_STATIC_ID #Static device numbering
# SCSI Controllers
device ahb # EISA AHA1742 family
device ahc # AHA2940 and onboard AIC7xxx devices
device amd # AMD 53C974 (Tekram DC-390(T))
device isp # Qlogic family
device ncr # NCR/Symbios Logic
device sym # NCR/Symbios Logic (newer chipsets)
options SYM_SETUP_LP_PROBE_MAP=0x40
# Allow ncr to attach legacy NCR devices
when
# both sym and ncr are configured
device adv0 at isa?
device adw
device bt0 at isa?
device aha0 at isa?
device aic0 at isa?
device ncv # NCR 53C500
device nsp # Workbit Ninja SCSI-3
device stg # TMC 18C30/18C50
# SCSI peripherals
device scbus # SCSI bus (required)
device da # Direct Access (disks)
device sa # Sequential Access (tape etc)
device cd # CD
device pass # Passthrough device (direct SCSI
access)
# RAID controllers interfaced to the SCSI subsystem
device asr # DPT SmartRAID V, VI and Adaptec SCSI
RAID
device dpt # DPT Smartcache - See LINT for options!
device iir # Intel Integrated RAID
device mly # Mylex AcceleRAID/eXtremeRAID
device ciss # Compaq SmartRAID 5* series
# RAID controllers
device aac # Adaptec FSA RAID, Dell PERC2/PERC3
device aacp # SCSI passthrough for aac (requires
CAM)
device ida # Compaq Smart RAID
device amr # AMI MegaRAID
device mlx # Mylex DAC960 family
device twe # 3ware Escalade
# atkbdc0 controls both the keyboard and the PS/2 mouse
device atkbdc0 at isa? port IO_KBD
device atkbd0 at atkbdc? irq 1 flags 0x1
device psm0 at atkbdc? irq 12
device vga0 at isa?
# splash screen/screen saver
pseudo-device splash
# syscons is the default console driver, resembling an SCO console
device sc0 at isa? flags 0x100
# Enable this and PCVT_FREEBSD for pcvt vt220 compatible console driver
#device vt0 at isa?
#options XSERVER # support for X server on a vt
console
#options FAT_CURSOR # start with block cursor
# If you have a ThinkPAD, uncomment this along with the rest of the PCVT
lines
#options PCVT_SCANSET=2 # IBM keyboards are non-std
# Floating point support - do not disable.
device npx0 at nexus? port IO_NPX irq 13
# Power management support (see LINT for more options)
device apm0 at nexus? disable flags 0x20 # Advanced Power
Management
# Serial (COM) ports
device sio0 at isa? port IO_COM1 flags 0x10 irq 4
device sio1 at isa? port IO_COM2 irq 3
device sio2 at isa? disable port IO_COM3 irq 5
device sio3 at isa? disable port IO_COM4 irq 9
# Parallel port
device ppc0 at isa? irq 7
device ppbus # Parallel port bus (required)
device lpt # Printer
device plip # TCP/IP over parallel
device ppi # Parallel port interface device
#device vpo # Requires scbus and da
device pcm #SOUND Blaster Device
device sbc #Bridge driver for sound blaster
# PCI Ethernet NICs.
device de # DEC/Intel DC21x4x (``Tulip'')
device em # Intel PRO/1000 adapter Gigabit
Ethernet Card (``Wiseman'')
device txp # 3Com 3cR990 (``Typhoon'')
device vx # 3Com 3c590, 3c595 (``Vortex'')
# PCI Ethernet NICs that use the common MII bus controller code.
# NOTE: Be sure to keep the 'device miibus' line in order to use these
NICs!
device miibus # MII bus support
device dc # DEC/Intel 21143 and various workalikes
device fxp # Intel EtherExpress PRO/100B (82557,
82558)
device pcn # AMD Am79C97x PCI 10/100 NICs
device rl # RealTek 8129/8139
device sf # Adaptec AIC-6915 (``Starfire'')
device sis # Silicon Integrated Systems SiS 900/SiS
7016
device ste # Sundance ST201 (D-Link DFE-550TX)
device tl # Texas Instruments ThunderLAN
device tx # SMC EtherPower II (83c170 ``EPIC'')
device vr # VIA Rhine, Rhine II
device wb # Winbond W89C840F
device xl # 3Com 3c90x (``Boomerang'',
``Cyclone'')
device bge # Broadcom BCM570x (``Tigon III'')
# ISA Ethernet NICs.
# 'device ed' requires 'device miibus'
device ed0 at isa? port 0x280 irq 10 iomem 0xd8000
device ex
device ep
device fe0 at isa? port 0x300
# Xircom Ethernet
device xe
# PRISM I IEEE 802.11b wireless NIC.
device awi
# WaveLAN/IEEE 802.11 wireless NICs. Note: the WaveLAN/IEEE really
# exists only as a PCMCIA device, so there is no ISA attachment needed
# and resources will always be dynamically assigned by the pccard code.
device wi
# Aironet 4500/4800 802.11 wireless NICs. Note: the declaration below
will
# work for PCMCIA and PCI cards, as well as ISA cards set to ISA PnP
# mode (the factory default). If you set the switches on your ISA
# card for a manually chosen I/O address and IRQ, you must specify
# those parameters here.
device an
# The probe order of these is presently determined by
i386/isa/isa_compat.c.
device ie0 at isa? port 0x300 irq 10 iomem 0xd0000
#device le0 at isa? port 0x300 irq 5 iomem 0xd0000
device lnc0 at isa? port 0x280 irq 10 drq 0
device cs0 at isa? port 0x300
device sn0 at isa? port 0x300 irq 10
# Pseudo devices - the number indicates how many units to allocate.
pseudo-device loop # Network loopback
pseudo-device ether # Ethernet support
pseudo-device sl 1 # Kernel SLIP
pseudo-device ppp 1 # Kernel PPP
pseudo-device tun # Packet tunnel.
pseudo-device pty # Pseudo-ttys (telnet etc)
pseudo-device md # Memory "disks"
pseudo-device gif # IPv6 and IPv4 tunneling
pseudo-device faith 1 # IPv6-to-IPv4 relaying (translation)
# The `bpf' pseudo-device enables the Berkeley Packet Filter.
# Be aware of the administrative consequences of enabling this!
pseudo-device bpf #Berkeley packet filter
# USB support
device uhci # UHCI PCI->USB interface
device ohci # OHCI PCI->USB interface
device usb # USB Bus (required)
device ugen # Generic
device uhid # "Human Interface Devices"
device ukbd # Keyboard
device ulpt # Printer
device umass # Disks/Mass storage - Requires scbus
and da
device ums # Mouse
device uscanner # Scanners
device urio # Diamond Rio MP3 Player
# USB Ethernet, requires mii
device aue # ADMtek USB ethernet
device cue # CATC USB ethernet
device kue # Kawasaki LSI USB ethernet
To Unsubscribe: send mail to [EMAIL PROTECTED]
with "unsubscribe freebsd-questions" in the body of the message
