Hi, There is a missing minus before ttt.
tcpdump -n -e -ttt -i pflog0 Necati. 2010/8/21 Free BSD <free...@vfemail.net> > Dear List members > > I have a server using two different NICs as a LACP lagg device. as per the > /etc/rc.conf file, the configuration is > > ifconfig_em0="up" > ifconfig_re0="up" > cloned_interfaces="lagg0" > ifconfig_lagg0="laggproto lacp laggport em0 laggport re0" > ipv4_addrs_lagg0="192.168.1.3/22" > > pflog_enable="YES" > pflog_logfile="/var/log/pflog" > pflog_program="/sbin/pflogd" > pflog_flags="" > > > and the ifconfig says > > em0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 > > > options=219b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,TSO4,WOL_MAGIC> > ether 00:22:19:1d:7b:a8 > media: Ethernet autoselect (1000baseT <full-duplex>) > status: active > re0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 > > > options=389b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,WOL_UCAST,WOL_MCAST,WOL_MAGIC> > ether 00:22:19:1d:7b:a8 > media: Ethernet autoselect (1000baseT <full-duplex>) > status: active > plip0: flags=8810<POINTOPOINT,SIMPLEX,MULTICAST> metric 0 mtu 1500 > pflog0: flags=141<UP,RUNNING,PROMISC> metric 0 mtu 33200 > lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384 > options=3<RXCSUM,TXCSUM> > inet6 fe80::1%lo0 prefixlen 64 scopeid 0x5 > inet6 ::1 prefixlen 128 > inet 127.0.0.1 netmask 0xff000000 > nd6 options=3<PERFORMNUD,ACCEPT_RTADV> > pfsync0: flags=0<> metric 0 mtu 1460 > syncpeer: 224.0.0.240 maxupd: 128 > enc0: flags=0<> metric 0 mtu 1536 > vboxnet0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500 > ether 0a:00:27:00:00:00 > lagg0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 > > options=209b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,WOL_MAGIC> > ether 00:22:19:1d:7b:a8 > inet 192.168.1.3 netmask 0xfffffc00 broadcast 192.168.3.255 > media: Ethernet autoselect > status: active > laggproto lacp > laggport: re0 flags=1c<ACTIVE,COLLECTING,DISTRIBUTING> > laggport: em0 flags=1c<ACTIVE,COLLECTING,DISTRIBUTING> > > > However, if I try to view the log, it says > > tcpdump -n -e ttt -i pflog0 > tcpdump: WARNING: em0: no IPv4 address assigned > tcpdump: syntax error > > I have also tried with -i lagg0, and the same error was generated. I'm not > sure if I'm doing something wrong. I went through the FB handbook as much as > I could, also googled around -- no luck. > > Any pointer / suggestion is welcom. > > Thanks. > > > > > ------------------------------------------------- > This message sent via VFEmail.net > http://www.vfemail.net > $14.95 Lifetime accounts - 1GB disk, No bandwidth quotas! > > _______________________________________________ > freebsd-pf@freebsd.org mailing list > http://lists.freebsd.org/mailman/listinfo/freebsd-pf > To unsubscribe, send any mail to "freebsd-pf-unsubscr...@freebsd.org" > -- N. Ersen SISECI http://www.enderunix.org _______________________________________________ freebsd-pf@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-pf To unsubscribe, send any mail to "freebsd-pf-unsubscr...@freebsd.org"
