On Thu, Feb 1, 2018, at 15:17, Marius Halden wrote: > Hi, > > We have two routers running FreeBSD r320487 (BSDRP) with bxe NICs, they > are connected together with a twinax cable and to our ISP with 1Gbit > fiber. The NICs in question are Broadcom BCM57840S (Supermicro AOC-STG- > B4S). > > The link between the routers will go down on one side not long after > it's brought up while staying up on the other side. I am not able to > bring the link back up without either unplugging the cable or powering > the routers off and on again, if I try to bring them up by taking them > down and up with ifconfig they will stay down no matter what the state > was before. > > After the routers have been up some time the console will be flooded > with messages like this: > > bxe0: ERROR: resource (0x0) in use (status 0xffffffff bit 0x1) > bxe0: ELINK EVENT LOG (3) > bxe0: ELINK EVENT LOG (3) > bxe0: ERROR: resource (0x0) in use (status 0xffffffff bit 0x1) > bxe0: ELINK EVENT LOG (3) > bxe0: ELINK EVENT LOG (3) > bxe0: ERROR: resource (0x0) in use (status 0xffffffff bit 0x1) > bxe0: ELINK EVENT LOG (3) > bxe0: ELINK EVENT LOG (3) > bxe0: ERROR: resource (0x0) in use (status 0xffffffff bit 0x1) > bxe0: ELINK EVENT LOG (3) > bxe0: ELINK EVENT LOG (3) > bxe0: ERROR: resource (0x0) in use (status 0xffffffff bit 0x1) > bxe0: ELINK EVENT LOG (3) > bxe0: ELINK EVENT LOG (3) > bxe0: ERROR: resource (0x0) in use (status 0xffffffff bit 0x1) > bxe0: ELINK EVENT LOG (3) > bxe0: ELINK EVENT LOG (3) > bxe0: ERROR: resource (0x0) in use (status 0xffffffff bit 0x1) > bxe0: ELINK EVENT LOG (3) > bxe0: ELINK EVENT LOG (3) > bxe0: ERROR: resource (0x0) in use (status 0xffffffff bit 0x1) > bxe0: ELINK EVENT LOG (3) > bxe0: ELINK EVENT LOG (3) > bxe0: ERROR: resource (0x0) in use (status 0xffffffff bit 0x1) > bxe0: ELINK EVENT LOG (3) > bxe0: ELINK EVENT LOG (3) > bxe0: ERROR: resource (0x0) in use (status 0xffffffff bit 0x1) > bxe0: ELINK EVENT LOG (3) > bxe0: ELINK EVENT LOG (3) > bxe0: ERROR: resource (0x0) in use (status 0xffffffff bit 0x1) > bxe0: ELINK EVENT LOG (3) > bxe0: ELINK EVENT LOG (3) > bxe0: ERROR: resource (0x0) in use (status 0xffffffff bit 0x1) > bxe0: ELINK EVENT LOG (3) > bxe0: ELINK EVENT LOG (3) > bxe0: ERROR: resource (0x0) in use (status 0xffffffff bit 0x1) > bxe0: ELINK EVENT LOG (3) > bxe0: ELINK EVENT LOG (3) > bxe0: ERROR: resource (0x0) in use (status 0xffffffff bit 0x1) > bxe0: ELINK EVENT LOG (3) > bxe0: ELINK EVENT LOG (3) > bxe0: ERROR: resource (0x0) in use (status 0xffffffff bit 0x1) > bxe0: ELINK EVENT LOG (3) > bxe0: ELINK EVENT LOG (3) > > This is not always limited to just one interface, but can include all > interfaces which are in use.
Trying to bringing down the interface with ifconfig, the following was logged: bxe0: ERROR: ECORE: timeout waiting for state 0 bxe0: ERROR: Failed to delete MACs (-4) mac_type 0 wait_for_comp 0x1 bxe0: ERROR: Failed to delete UC MACs list (-4) bxe0: ERROR: FW failed to respond! bxe0: ERROR: ECORE: timeout waiting for state 7 bxe0: ERROR: ECORE: timeout waiting for state 2 bxe0: ERROR: FUNC_STOP ramrod failed. Running a dry transaction (-4) bxe0: ERROR: proper val not read from IGU! bxe0: ERROR: ECORE: Unknown reset_phase (0x0) from MCP bxe0: ERROR: FW failed to respond! bxe0: ERROR: Parity error: HW block parity attention: [0]:0x55540000 [1]:0x55555555 [2]:0x00005555 [3]:0xf0000000 [4]:0x00000028 bxe0: ERROR: resource (0xb) in use (status 0xffffffff bit 0x800) bxe0: ERROR: resource (0xb) in use (status 0xffffffff bit 0x800) bxe0: ERROR: resource (0xb) in use (status 0xffffffff bit 0x800) Is this a hardware or a driver issue? -- Marius Halden _______________________________________________ freebsd-net@freebsd.org mailing list https://lists.freebsd.org/mailman/listinfo/freebsd-net To unsubscribe, send any mail to "freebsd-net-unsubscr...@freebsd.org"
