Hi Sami, I haven't actually fixed anything yet. I have only demonstrated that the poor performance does not appear to happen between two FreeBSD boxes and possibly between a Linux and FreeBSD, but I am going to confirm that now. I have also seen good performance between the Windows box and Linux so that doesn't quite add up either. I may have to break out Wireshark and make some packet captures to see if I can tell what's going on. If I find anything, I will be sure to share it.
Regards, Chris From: "Sami Halabi" <sodyn...@gmail.com> To: "chris" <ch...@dunbar.net> Cc: "freebsd-net" <freebsd-net@freebsd.org> Sent: Friday, July 22, 2016 8:34:30 AM Subject: Re: Slow performance with Intel X540-T2 10Gb NIC hi, would you share what was wrong in the windows side and how you solved it? Sami בתאריך 22 ביולי 2016 12:33 AM, "Chris Dunbar" < ch...@dunbar.net > כתב: Hello again, I have good news and bad news: The bad news first: I am an idiot and I have wasted some of your time for which I apologize. The good news: Testing now between two FreeBSD 10.3 systems, I am achieving blistering speeds with iperf3. I apparently fell into the trap of assuming the new thing (FreeBSD is new to me) was broken. Now I see that I was assuming Windows was working fine and focusing all my attention on FreeBSD. Looking back over everything I have done to troubleshoot this situation I must conclude that the performance issue was on the Windows side and not the FreeBSD side. I am less concerned about that because my ultimate goal is to install my three X540s into one FreeBSD server and two VMware ESXi hosts. I am now fairly confident performance will be great. Many thanks for your collective attention and the suggestions I received from Eric and others. Regards, Chris ----- Original Message ----- From: "chris" < ch...@dunbar.net > To: "freebsd-net" < freebsd-net@freebsd.org > Sent: Thursday, July 21, 2016 4:53:40 PM Subject: Re: Slow performance with Intel X540-T2 10Gb NIC Eric, et al: I haven't tried netperf yet, but I do have some new information to share. I have two systems that I am using for testing: the new server and an older (not too old) desktop PC. I installed CentOS on the new server again because I know it can achieve >9 GB/s with the X540. I replaced Windows on the desktop PC with FreeBSD 10.3 (it also has an X540) and ran iperf3 again. I was able to achieve >9 GB/s so I know the problem isn't the X540 and I know the problem isn't anything with the default installation of FreeBSD 10.3. So, what in the world might be nutty in my BIOS settings (or elsewhere) that would cause the new server + FreeBSD 10.3 + X540 to equal slow performance? Regards, Chris From: "Eric Joyner" < e...@freebsd.org > To: "chris" < ch...@dunbar.net >, "freebsd-net" < freebsd-net@freebsd.org > Sent: Thursday, July 21, 2016 1:27:10 PM Subject: Re: Slow performance with Intel X540-T2 10Gb NIC (Replying-all this time) Did you try to set these settings that ESnet recommends? https://fasterdata.es.net/host-tuning/freebsd/ We don't use iperf3 here at Intel (we use netperf instead), so I'm not sure I can be much help diagnosing what's wrong. On Wed, Jul 20, 2016 at 5:39 PM Chris Dunbar < ch...@dunbar.net > wrote: Hello, I am new to FreeBSD and recently built a file server out of new components running FreeBSD 10.3. I installed an Intel X540-T2 10 Gb NIC and am experiencing what I consider to be slow transfer speeds. I am using iperf3 to measure the speed and test the results of modifications. So far nothing I have done has made a noticeable difference. If I run iperf3 -s on the FreeBSD server, I see transfer speeds of approximately 1.6 Gb/s. If I run iperf3 in client mode, the speed improves to ~2.75 Gb/s. However, if I replace FreeBSD with CentOS 7 on the same hardware, I see iperf3 speeds surpassing 8 GB/s. The other end of my iperf3 test is a Windows 10 box that also has an Intel X540-T2 installed. I did notice that FreeBSD 10.3 (and 11.0 alpha 6 for that matter) includes a slightly older Intel driver (v3.1.13-k). I managed to build a custom kernel that removed the Intel PRO/10GbE PCIE NIC drivers. That allowed me to manually load the latest 3.1.14 driver downloaded from Intel's web site. Unfortunately that did not produce any improvements. I am working my way through man tuning() and some other articles on network performance. So far nothing I tweak makes a noticeable difference. I'm increasingly skeptical that I am going to find a setting or two that more than doubles the speed I am currently experiencing. I am open to any and all suggestions at this point. Thank you! Chris _______________________________________________ freebsd-net@freebsd.org mailing list https://lists.freebsd.org/mailman/listinfo/freebsd-net To unsubscribe, send any mail to " freebsd-net-unsubscr...@freebsd.org " _______________________________________________ freebsd-net@freebsd.org mailing list https://lists.freebsd.org/mailman/listinfo/freebsd-net To unsubscribe, send any mail to " freebsd-net-unsubscr...@freebsd.org " _______________________________________________ freebsd-net@freebsd.org mailing list https://lists.freebsd.org/mailman/listinfo/freebsd-net To unsubscribe, send any mail to " freebsd-net-unsubscr...@freebsd.org " _______________________________________________ freebsd-net@freebsd.org mailing list https://lists.freebsd.org/mailman/listinfo/freebsd-net To unsubscribe, send any mail to "freebsd-net-unsubscr...@freebsd.org"
