On 07/10/13 19:47, Guido Falsi wrote:
On 07/10/13 09:04, Yonghyeon PYUN wrote:
On Tue, Jul 09, 2013 at 10:28:29PM +0200, Guido Falsi wrote:
Hi,
I have a PC with an integrate re ethernet interface, pciconf identifies
it like this:
re0@pci0:3:0:0: class=0x020000 card=0x11c01734 chip=0x816810ec rev=0x07
hdr=0x00
I'm running FreeBSD current r252261.
As stated in the subject after boot the interface does not work
correctly.
Using tcpdump on another host I noticed that packets (ICMP echo requests
for example) do get sent, and replies generated by the other host, but
the kernel does not seem to see them. Except that every now and then
some packet does get to the system.
I'm seeing packet 7, 27, 47, 66, 86, 106, 125, 144, 164, 183 and so on
from a ping which has been running for some time. Just about one every
twenty. Some pattern is showing up.
this is the output of ifconfig re0 after boot:
re0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu
1500
options=8209b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,WOL_MAGIC,LINKSTATE>
ether 00:19:99:f8:d3:0b
inet 172.24.42.13 netmask 0xffffff00 broadcast 172.24.42.255
inet6 fe80::219:99ff:fef8:d30b%re0 prefixlen 64 scopeid 0x2
nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL>
media: Ethernet autoselect (100baseTX <full-duplex>)
status: active
If I just touch any interface flag with ifconfig, anyone, tso, -txcsum
-rxcsum, it starts working flawlessly. It keeps working also if I
perform the opposite operation with ifconfig afterwards, so it is not
the flag itself fixing it.
This is an ifconfig after performing this exercise(it's the same, since
I disabled txcsum and reactivated it in this instance):
re0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu
1500
options=8209b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,WOL_MAGIC,LINKSTATE>
ether 00:19:99:f8:d3:0b
inet 172.24.42.13 netmask 0xffffff00 broadcast 172.24.42.255
inet6 fe80::219:99ff:fef8:d30b%re0 prefixlen 64 scopeid 0x2
nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL>
media: Ethernet autoselect (100baseTX <full-duplex>)
status: active
I don't know much about FreeBSD network drivers so i can't make theories
about this. I hope someone has an idea what the problem could be.
I'm available for any further information needed, test, experiment and
so on.
Could you show me dmesg output(re(4) and rgephy(4) only)?
re0: <RealTek 8168/8111 B/C/CP/D/DP/E/F PCIe Gigabit Ethernet> port
0xd000-0xd0ff mem 0xf2104000-0xf2104fff,0xf2100000-0xf2103fff irq 17 at
device 0.0 on pci3
re0: Using 1 MSI-X message
re0: turning off MSI enable bit.
re0: Chip rev. 0x2c800000
re0: MAC rev. 0x00000000
re0: Ethernet address: 00:19:99:f8:d3:0b
miibus0: <MII bus> on re0
rgephy0: <RTL8169S/8110S/8211 1000BASE-T media interface> PHY 1 on miibus0
rgephy0: none, 10baseT, 10baseT-FDX, 10baseT-FDX-flow, 100baseTX,
100baseTX-FDX, 100baseTX-FDX-flow, 1000baseT, 1000baseT-master,
1000baseT-FDX, 1000baseT-FDX-master, 1000baseT-FDX-flow,
1000baseT-FDX-flow-master, auto, auto-flow
Also, I'm loading this as a module, but, for as much as I know, this
should not make any difference.
Did it ever work or you see the issue only on CURRENT?
Never worked on this machine (I own it since the last days of February).
I only installed current on it. If needed I can find time to test a
recent 9.x snapshot on it.
Sorry for the delay.
I tested with a 9.2 PRERELEASE snapshot and it shows the same behavior
it shows on CURRENT.
Any further tests or things I can do to help diagnose this problem?
--
Guido Falsi <m...@madpilot.net>
_______________________________________________
freebsd-net@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-net
To unsubscribe, send any mail to "freebsd-net-unsubscr...@freebsd.org"
