I've got an Atheros card, AR2425, which is supposed to be supported by
ath_hal(4), according to the man page.
dmesg|grep -i Ath
ath0: <Atheros 5424/2424> mem 0xd6000000-0xd600ffff irq 16 at device 0.0
on pci2
ath0: AR2425 mac 14.2 RF5424 phy 7.0
I can see that ath_hal is listed in the kernel config file:
egrep 'ath_|wlan_' GENERIC
device wlan_wep # 802.11 WEP support
device wlan_ccmp # 802.11 CCMP support
device wlan_tkip # 802.11 TKIP support
device wlan_amrr # AMRR transmit rate control algorithm
device ath_pci # Atheros pci/cardbus glue
device ath_hal # pci/cardbus chip support
device ath_rate_sample # SampleRate tx rate control for ath
kldstat doesn't show ath_hal as having been loaded. Is that normal?
kldstat -v|egrep 'wlan|ath_'
98 pci/ath_pci
434 wlan
433 wlan_wep
432 wlan_tkip
431 wlan_ccmp
430 wlan_amrr
436 wlan_sta 435 wlan_ratectl_none
Long story short, I can't seem to be able to configure my wireless,
despite following the instructions given in the handbook.
Here's my /etc/rc.conf:
cat /etc/rc.conf
hostname="box0"
sshd_enable="YES"
moused_enable="YES"
ntpd_enable="YES"
powerd_enable="YES"
# Set dumpdev to "AUTO" to enable crash dumps, "NO" to disable
dumpdev="AUTO"
wlans_ath0="wlan0"
ifconfig_wlan0="ssid plan9 WPA DHCP"
hald_enable="YES"
dbus_enable="YES"
linux_enable="YES"
ifconfig_re0="DHCP"
And my /etc/wpa_supplicant.conf:
cat /etc/wpa_supplicant.conf
ctrl_interface=/var/run/wpa_supplicant
eapol_version=2
ap_scan=1
fast_reauth=1
network={
ssid="plan9"
psk=wpa_passphrase-generated psk
}
ifconfig -a
ath0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 2290
ether 00:24:2c:5e:06:f2
nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL>
media: IEEE 802.11 Wireless Ethernet autoselect mode 11g
status: associated
re0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=8209b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,WOL_MAGIC,LINKSTATE>
ether 00:23:8b:b2:e5:1f
inet 192.168.1.3 netmask 0xffffff00 broadcast 192.168.1.255
nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL>
media: Ethernet autoselect (100baseTX <full-duplex>)
status: active
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384
options=600003<RXCSUM,TXCSUM,RXCSUM_IPV6,TXCSUM_IPV6>
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0xb
inet 127.0.0.1 netmask 0xff000000
nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
wlan0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
ether 00:24:2c:5e:06:f2
nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL>
media: IEEE 802.11 Wireless Ethernet autoselect (autoselect)
status: no carrier
ssid plan9 channel 1 (2412 MHz 11g)
regdomain 103 indoor ecm authmode WPA1+WPA2/802.11i privacy OFF
txpower 20 bmiss 7 scanvalid 450 bgscan bgscanintvl 300
bgscanidle 250
roam:rssi 7 roam:rate 5 protmode CTS wme burst roaming MANUAL
'ifconfig wlan0 list scan' returns nothing.
uname -a
FreeBSD box0 9.1-RELEASE-p3 FreeBSD 9.1-RELEASE-p3 #0: Mon Apr 29
18:11:52 UTC 2013
r...@amd64-builder.daemonology.net:/usr/obj/usr/src/sys/GENERIC i386
I've tried everything I could think of, still no luck.
Any pointers would be appreciated.
Alexander Kapshuk.
_______________________________________________
freebsd-net@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-net
To unsubscribe, send any mail to "freebsd-net-unsubscr...@freebsd.org"
