Hi Folks,
I have a pair of Chelsio T4 cards installed in a new HP DL380
system. The driver does not load at boot time, failing with the
message:
t4nex0: failed to pre-process config file: 2.
After the system has finished booting, if I then issue a
'kldload if_cxgbe' command, the driver loads correctly. Note,
the driver loads correctly from the command prompt with or
without the if_cxgbe_load in /boot/loader.conf.
The message is coming from t4_main.c:partition_resources().
I don't see anything obvious that would cause this:
rc = cfg ? upload_config_file(sc, cfg, &mtype, &maddr) : ENOENT;
if (rc != 0) {
mtype = FW_MEMTYPE_CF_FLASH;
maddr = t4_flash_cfg_addr(sc);
}
bzero(&caps, sizeof(caps));
caps.op_to_write = htobe32(V_FW_CMD_OP(FW_CAPS_CONFIG_CMD) |
F_FW_CMD_REQUEST | F_FW_CMD_READ);
caps.cfvalid_to_len16 = htobe32(F_FW_CAPS_CONFIG_CMD_CFVALID |
V_FW_CAPS_CONFIG_CMD_MEMTYPE_CF(mtype) |
V_FW_CAPS_CONFIG_CMD_MEMADDR64K_CF(maddr >> 16) | FW_LEN16(caps));
rc = -t4_wr_mbox(sc, sc->mbox, &caps, sizeof(caps), &caps);
if (rc != 0) {
device_printf(sc->dev,
"failed to pre-process config file: %d.\n", rc);
return (rc);
}
Has anyone run into this?
Thanks,
John
ps: And the output from loading the driver module by hand:
t4nex0: <Chelsio T440-CR> mem
0xf7cc0000-0xf7cfffff,0xf7000000-0xf77fffff,0xf6ff0000-0xf6ff1fff irq 26 at
device 0.4 on pci7
t4nex0: installing firmware 1.8.4.0 on card.
cxgbe0: <port 0> on t4nex0
cxgbe0: Ethernet address: 00:07:43:11:e9:00
cxgbe0: 16 txq, 8 rxq
cxgbe1: <port 1> on t4nex0
cxgbe1: Ethernet address: 00:07:43:11:e9:08
cxgbe1: 16 txq, 8 rxq
cxgbe2: <port 2> on t4nex0
cxgbe2: Ethernet address: 00:07:43:11:e9:10
cxgbe2: 16 txq, 8 rxq
cxgbe3: <port 3> on t4nex0
cxgbe3: Ethernet address: 00:07:43:11:e9:18
cxgbe3: 16 txq, 8 rxq
t4nex0: PCIe x8, 4 ports, 34 MSI-X interrupts, 101 eq, 33 iq
t4nex1: <Chelsio T440-CR> mem
0xfbcc0000-0xfbcfffff,0xfb000000-0xfb7fffff,0xfaff0000-0xfaff1fff irq 58 at
device 0.4 on pci36
t4nex1: installing firmware 1.8.4.0 on card.
cxgbe4: <port 0> on t4nex1
cxgbe4: Ethernet address: 00:07:43:11:e6:a0
cxgbe4: 16 txq, 8 rxq
cxgbe5: <port 1> on t4nex1
cxgbe5: Ethernet address: 00:07:43:11:e6:a8
cxgbe5: 16 txq, 8 rxq
cxgbe6: <port 2> on t4nex1
cxgbe6: Ethernet address: 00:07:43:11:e6:b0
cxgbe6: 16 txq, 8 rxq
cxgbe7: <port 3> on t4nex1
cxgbe7: Ethernet address: 00:07:43:11:e6:b8
cxgbe7: 16 txq, 8 rxq
t4nex1: PCIe x8, 4 ports, 34 MSI-X interrupts, 101 eq, 33 iq
_______________________________________________
freebsd-net@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-net
To unsubscribe, send any mail to "freebsd-net-unsubscr...@freebsd.org"
