14.01.2012 0:15, YongHyeon PYUN wrote: > On Fri, Jan 13, 2012 at 11:17:45PM +0200, Vladislav V. Prodan wrote: >> >> Tell me, what a performance in pps a network card RTL8111/8168B? >> Can I somehow increase it? >> Experimentally, since it begins to fall off 80Kpps: ( >> > > RX performance number will show much better than that but TX is > major bottleneck of controller. I tried hard to enhance TX > performance for the controller but I'm under the impression that > that number would be the maximum(around 90Kpps) and this is also > similar number what I got on Linux. > Given that re(4) controllers are for non-server grade systems I > wouldn't be surprised to see that number. If you need higher pps, > choose controllers targeted for servers. Alternatively, low cost > controllers from JMicron/Atheros also show decent TX/RX > performance numbers.
That's why I would like to get some numerical limitations of the controller re (4). While there is no way to put a network card from Intel. > >> >> Jan 13 18:12:49 XXX kernel: re0: watchdog timeout >> Jan 13 18:12:49 XXX kernel: re0: link state changed to DOWN >> Jan 13 18:12:53 XXX kernel: re0: link state changed to UP >> > > I'm more concerned on watchdog timeouts than performance numbers. > Would you show me re(4) related message from dmesg(8) output? See dmesg output below. > And if you know how to reliably trigger the watchdog timeout, would > you share with us? DDoS attack has undergone server and choked these packages: ( Trafshow showed a peak of 110K pps, but immediately operational watchdog timeout. I would appreciate help in setting up a network interface, so as long as it is not turned off by such scams. >> >> >> # uname -a >> FreeBSD pvppw.org 9.0-PRERELEASE FreeBSD 9.0-PRERELEASE #1: Mon Dec 5 >> 14:56:07 EET 2011 root@XXX:/usr/obj/usr/src/sys/XXX.2 amd64 >> >> # pciconf -lv | grep -A 4 "re0@" >> re0@pci0:2:0:0: class=0x020000 card=0x84321043 chip=0x816810ec rev=0x06 >> hdr=0x00 >> vendor = 'Realtek Semiconductor Co., Ltd.' >> device = 'RTL8111/8168B PCI Express Gigabit Ethernet controller' >> class = network >> subclass = ethernet >> > > RealTek controllers tend to use the same PCI id for different > controllers so pciconf(8) does not help here. re(4) may have shown > more details on your controller in dmesg output. > Jan 13 18:57:03 XXX kernel: re0: <RealTek 8168/8111 B/C/CP/D/DP/E PCIe Gigabit Ethernet> port 0xe800-0xe8ff mem 0xfcfff000-0xfcffffff,0xfcffffff,0xfcff8000-0xfcffbfff irq 18 at device 0.0 on pci2 Jan 13 18:57:03 XXX kernel: re0: Using 1 MSI-X message Jan 13 18:57:03 XXX kernel: re0: Chip rev. 0x2c800000 Jan 13 18:57:03 XXX kernel: re0: MAC rev. 0x00000000 Jan 13 18:57:03 XXX kernel: miibus0: <MII bus> on re0 Jan 13 18:57:03 XXX kernel: rgephy0: <RTL8169S/8110S/8211 1000BASE-T media interface> PHY 1 on miibus0 Jan 13 18:57:03 XXX kernel: rgephy0: none, 10baseT, 10baseT-FDX, 10baseT-FDX-flow, 100baseTX, 100baseTX-FDX, 100baseTX-FDX-flow, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, 1000baseT-FDX-flow, 1000baseT-FDX-flow-master, auto, auto-flow Jan 13 18:57:03 XXX kernel: re0: Ethernet address: 14:da:e9:75:5f:ee -- Vladislav V. Prodan System & Network Administrator http://support.od.ua +380 67 4584408, +380 99 4060508 VVP88-RIPE _______________________________________________ freebsd-net@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-net To unsubscribe, send any mail to "freebsd-net-unsubscr...@freebsd.org"
