Hi Folks, I have a dell R900 - it came with a quad card Broadcom NetXtreme II BCM5708 and I installed the 8.1 release amd64.
The bce connected to a switch foundry says 'no carrier', another bce connected to a router (juniper) works fine. I found some old threads about the bce driver. http://www.freebsd.org/cgi/query-pr.cgi?pr=118238 and http://unix.derkeiler.com/Mailing-Lists/FreeBSD/net/2007-11/msg00211.html Below are boot messages regarding bce. Any ideas on what I should try ? ( just now tried the 8.2 prerelease 0 - no luck) thanks, -Ed. module_register: module bce/miibus already exists! Module bce/miibus failed to register: 17 module_register: module pci/bce already exists! Module pci/bce failed to register: 17 bce0: <Broadcom NetXtreme II BCM5708 1000Base-T (B2)> mem 0xd6000000-0xd7ffffff irq 18 at device 0.0 on pci11 miibus0: <MII bus> on bce0 bce0: Ethernet address: 00:26:b9:35:08:dc bce0: [ITHREAD] bce0: ASIC (0x57081020); Rev (B2); Bus (PCI-X, 64-bit, 133MHz); B/C (5.0.4); Flags (MSI|MFW); MFW (ipms 1.6.0) bce1: <Broadcom NetXtreme II BCM5708 1000Base-T (B2)> mem 0xd8000000-0xd9ffffff irq 19 at device 0.0 on pci9 miibus1: <MII bus> on bce1 bce1: Ethernet address: 00:26:b9:35:08:da bce1: [ITHREAD] bce1: ASIC (0x57081020); Rev (B2); Bus (PCI-X, 64-bit, 133MHz); B/C (5.0.4); Flags (MSI|MFW); MFW (ipms 1.6.0) bce2: <Broadcom NetXtreme II BCM5708 1000Base-T (B2)> mem 0xda000000-0xdbffffff irq 37 at device 0.0 on pci7 miibus2: <MII bus> on bce2 bce2: Ethernet address: 00:26:b9:35:08:d8 bce2: [ITHREAD] bce2: ASIC (0x57081020); Rev (B2); Bus (PCI-X, 64-bit, 133MHz); B/C (5.0.4); Flags (MSI|MFW); MFW (UMP 1.1.9) bce3: <Broadcom NetXtreme II BCM5708 1000Base-T (B2)> mem 0xdc000000-0xddffffff irq 38 at device 0.0 on pci5 miibus3: <MII bus> on bce3 bce3: Ethernet address: 00:26:b9:35:08:d6 bce3: [ITHREAD] bce3: ASIC (0x57081020); Rev (B2); Bus (PCI-X, 64-bit, 133MHz); B/C (5.0.4); Flags (MSI|MFW); MFW (UMP 1.1.9) bce0: bce_pulse(): Bootcode lost the driver pulse! (bc_state = 0x00002006) bce1: bce_pulse(): Bootcode lost the driver pulse! (bc_state = 0x00002006) bce2: bce_pulse(): Bootcode lost the driver pulse! (bc_state = 0x00004006) bce3: bce_pulse(): Bootcode lost the driver pulse! (bc_state = 0x00004006) and full dmesg: Copyright (c) 1992-2010 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 8.1-RELEASE #0: Mon Jul 19 02:36:49 UTC 2010 r...@mason.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC amd64 module_register: module bce/miibus already exists! Module bce/miibus failed to register: 17 module_register: module pci/bce already exists! Module pci/bce failed to register: 17 Timecounter "i8254" frequency 1193182 Hz quality 0 CPU: Intel(R) Xeon(R) CPU E7440 @ 2.40GHz (2398.69-MHz K8-class CPU) Origin = "GenuineIntel" Id = 0x106d1 Family = 6 Model = 1d Stepping = 1 Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> Features2=0xce3bd<SSE3,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,DCA,SSE4.1> AMD Features=0x20100800<SYSCALL,NX,LM> AMD Features2=0x1<LAHF> TSC: P-state invariant real memory = 68719476736 (65536 MB) avail memory = 66333831168 (63260 MB) ACPI APIC Table: <DELL PE_SC3 > FreeBSD/SMP: Multiprocessor System Detected: 16 CPUs FreeBSD/SMP: 4 package(s) x 4 core(s) cpu0 (BSP): APIC ID: 0 cpu1 (AP): APIC ID: 1 cpu2 (AP): APIC ID: 2 cpu3 (AP): APIC ID: 3 cpu4 (AP): APIC ID: 8 cpu5 (AP): APIC ID: 9 cpu6 (AP): APIC ID: 10 cpu7 (AP): APIC ID: 11 cpu8 (AP): APIC ID: 16 cpu9 (AP): APIC ID: 17 cpu10 (AP): APIC ID: 18 cpu11 (AP): APIC ID: 19 cpu12 (AP): APIC ID: 24 cpu13 (AP): APIC ID: 25 cpu14 (AP): APIC ID: 26 cpu15 (AP): APIC ID: 27 ioapic0: Changing APIC ID to 6 ioapic1: Changing APIC ID to 7 ioapic0 <Version 2.0> irqs 0-23 on motherboard ioapic1 <Version 2.0> irqs 32-55 on motherboard kbd1 at kbdmux0 acpi0: <DELL PE_SC3> on motherboard acpi0: [ITHREAD] acpi0: Power Button (fixed) Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0 cpu0: <ACPI CPU> on acpi0 ACPI Warning for \\_PR_.CPU0._CST: Return Package is too small - found 3 elements, expected 3 (20100331/nspredef-787) cpu0: invalid _CST state count (3 != 2) cpu1: <ACPI CPU> on acpi0 ACPI Warning for \\_PR_.CPU1._CST: Return Package is too small - found 3 elements, expected 3 (20100331/nspredef-787) cpu1: invalid _CST state count (3 != 2) cpu2: <ACPI CPU> on acpi0 ACPI Warning for \\_PR_.CPU2._CST: Return Package is too small - found 3 elements, expected 3 (20100331/nspredef-787) cpu2: invalid _CST state count (3 != 2) cpu3: <ACPI CPU> on acpi0 ACPI Warning for \\_PR_.CPU3._CST: Return Package is too small - found 3 elements, expected 3 (20100331/nspredef-787) cpu3: invalid _CST state count (3 != 2) cpu4: <ACPI CPU> on acpi0 ACPI Warning for \\_PR_.CPU4._CST: Return Package is too small - found 3 elements, expected 3 (20100331/nspredef-787) cpu4: invalid _CST state count (3 != 2) cpu5: <ACPI CPU> on acpi0 ACPI Warning for \\_PR_.CPU5._CST: Return Package is too small - found 3 elements, expected 3 (20100331/nspredef-787) cpu5: invalid _CST state count (3 != 2) cpu6: <ACPI CPU> on acpi0 ACPI Warning for \\_PR_.CPU6._CST: Return Package is too small - found 3 elements, expected 3 (20100331/nspredef-787) cpu6: invalid _CST state count (3 != 2) cpu7: <ACPI CPU> on acpi0 ACPI Warning for \\_PR_.CPU7._CST: Return Package is too small - found 3 elements, expected 3 (20100331/nspredef-787) cpu7: invalid _CST state count (3 != 2) --More--(byte 3522) cpu13 (AP): APIC ID: 25 cpu14 (AP): APIC ID: 26 cpu15 (AP): APIC ID: 27 ioapic0: Changing APIC ID to 6 ioapic1: Changing APIC ID to 7 ioapic0 <Version 2.0> irqs 0-23 on motherboard ioapic1 <Version 2.0> irqs 32-55 on motherboard kbd1 at kbdmux0 acpi0: <DELL PE_SC3> on motherboard acpi0: [ITHREAD] acpi0: Power Button (fixed) Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0 cpu0: <ACPI CPU> on acpi0 ACPI Warning for \\_PR_.CPU0._CST: Return Package is too small - found 3 elements, expected 3 (20100331/nspredef-787) cpu0: invalid _CST state count (3 != 2) cpu1: <ACPI CPU> on acpi0 ACPI Warning for \\_PR_.CPU1._CST: Return Package is too small - found 3 elements, expected 3 (20100331/nspredef-787) cpu1: invalid _CST state count (3 != 2) cpu2: <ACPI CPU> on acpi0 ACPI Warning for \\_PR_.CPU2._CST: Return Package is too small - found 3 elements, expected 3 (20100331/nspredef-787) cpu2: invalid _CST state count (3 != 2) cpu3: <ACPI CPU> on acpi0 ACPI Warning for \\_PR_.CPU3._CST: Return Package is too small - found 3 elements, expected 3 (20100331/nspredef-787) cpu3: invalid _CST state count (3 != 2) cpu4: <ACPI CPU> on acpi0 ACPI Warning for \\_PR_.CPU4._CST: Return Package is too small - found 3 elements, expected 3 (20100331/nspredef-787) cpu4: invalid _CST state count (3 != 2) cpu5: <ACPI CPU> on acpi0 ACPI Warning for \\_PR_.CPU5._CST: Return Package is too small - found 3 elements, expected 3 (20100331/nspredef-787) cpu5: invalid _CST state count (3 != 2) cpu6: <ACPI CPU> on acpi0 ACPI Warning for \\_PR_.CPU6._CST: Return Package is too small - found 3 elements, expected 3 (20100331/nspredef-787) cpu6: invalid _CST state count (3 != 2) cpu7: <ACPI CPU> on acpi0 ACPI Warning for \\_PR_.CPU7._CST: Return Package is too small - found 3 elements, expected 3 (20100331/nspredef-787) cpu7: invalid _CST state count (3 != 2) cpu8: <ACPI CPU> on acpi0 ACPI Warning for \\_PR_.CPU8._CST: Return Package is too small - found 3 elements, expected 3 (20100331/nspredef-787) cpu8: invalid _CST state count (3 != 2) cpu9: <ACPI CPU> on acpi0 ACPI Warning for \\_PR_.CPU9._CST: Return Package is too small - found 3 elements, expected 3 (20100331/nspredef-787) cpu9: invalid _CST state count (3 != 2) cpu10: <ACPI CPU> on acpi0 ACPI Warning for \\_PR_.CP10._CST: Return Package is too small - found 3 elements, expected 3 (20100331/nspredef-787) cpu10: invalid _CST state count (3 != 2) cpu11: <ACPI CPU> on acpi0 ACPI Warning for \\_PR_.CP11._CST: Return Package is too small - found 3 elements, expected 3 (20100331/nspredef-787) cpu11: invalid _CST state count (3 != 2) cpu12: <ACPI CPU> on acpi0 ACPI Warning for \\_PR_.CP12._CST: Return Package is too small - found 3 elements, expected 3 (20100331/nspredef-787) cpu12: invalid _CST state count (3 != 2) cpu13: <ACPI CPU> on acpi0 ACPI Warning for \\_PR_.CP13._CST: Return Package is too small - found 3 elements, expected 3 (20100331/nspredef-787) cpu13: invalid _CST state count (3 != 2) cpu14: <ACPI CPU> on acpi0 ACPI Warning for \\_PR_.CP14._CST: Return Package is too small - found 3 elements, expected 3 (20100331/nspredef-787) cpu14: invalid _CST state count (3 != 2) cpu15: <ACPI CPU> on acpi0 ACPI Warning for \\_PR_.CP15._CST: Return Package is too small - found 3 elements, expected 3 (20100331/nspredef-787) cpu15: invalid _CST state count (3 != 2) acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0 Timecounter "HPET" frequency 14318180 Hz quality 900 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 pci0: <ACPI PCI bus> on pcib0 pcib1: <ACPI PCI-PCI bridge> irq 36 at device 1.0 on pci0 pci20: <ACPI PCI bus> on pcib1 pcib2: <ACPI PCI-PCI bridge> irq 17 at device 2.0 on pci0 pci22: <ACPI PCI bus> on pcib2 pcib3: <ACPI PCI-PCI bridge> irq 17 at device 0.0 on pci22 pci23: <ACPI PCI bus> on pcib3 pcib4: <ACPI PCI-PCI bridge> irq 17 at device 0.0 on pci23 pci25: <ACPI PCI bus> on pcib4 mfi0: <Dell PERC 6> port 0xec00-0xecff mem 0xde380000-0xde3bffff,0xde3c0000-0xde3fffff irq 17 at device 0.0 on pci25 mfi0: Megaraid SAS driver Ver 3.00 mfi0: 6684 (345318197s/0x0020/info) - Shutdown command received from host mfi0: 6685 (boot + 3s/0x0020/info) - Firmware initialization started (PCI ID 0060/1000/1f0c/1028) mfi0: 6686 (boot + 3s/0x0020/info) - Firmware version 1.22.02-0612 mfi0: 6687 (boot + 23s/0x0008/info) - Battery Present mfi0: 6688 (boot + 23s/0x0020/info) - Controller hardware revision ID (0x0) mfi0: 6689 (boot + 23s/0x0020/info) - Package version 6.2.0-0013 mfi0: 6690 (boot + 23s/0x0020/info) - Board Revision mfi0: 6691 (boot + 48s/0x0004/info) - Enclosure PD 20(c None/p0) communication restored mfi0: 6692 (boot + 49s/0x0002/info) - Inserted: Encl PD 20 mfi0: 6693 (boot + 49s/0x0002/info) - Inserted: PD 20(c None/p0) Info: enclPd=20, scsiType=d, portMap=09, sasAddr=5002609049922a00,0000000000000000 mfi0: 6694 (boot + 49s/0x0002/info) - Inserted: PD 00(e0x20/s0) mfi0: 6695 (boot + 49s/0x0002/info) - Inserted: PD 00(e0x20/s0) Info: enclPd=20, scsiType=0, portMap=00, sasAddr=5000c50010012dd1,0000000000000000 mfi0: 6696 (boot + 49s/0x0002/info) - Inserted: PD 01(e0x20/s1) mfi0: 6697 (boot + 49s/0x0002/info) - Inserted: PD 01(e0x20/s1) Info: enclPd=20, scsiType=0, portMap=01, sasAddr=5000c50010018bc1,0000000000000000 mfi0: 6698 (boot + 49s/0x0002/info) - Inserted: PD 02(e0x20/s2) mfi0: 6699 (boot + 49s/0x0002/info) - Inserted: PD 02(e0x20/s2) Info: enclPd=20, scsiType=0, portMap=02, sasAddr=5000c50010012dad,0000000000000000 mfi0: 6700 (boot + 49s/0x0002/info) - Inserted: PD 03(e0x20/s3) mfi0: 6701 (boot + 49s/0x0002/info) - Inserted: PD 03(e0x20/s3) Info: enclPd=20, scsiType=0, portMap=03, sasAddr=5000c50010012da9,0000000000000000 mfi0: 6702 (boot + 49s/0x0002/info) - Inserted: PD 04(e0x20/s4) mfi0: 6703 (boot + 49s/0x0002/info) - Inserted: PD 04(e0x20/s4) Info: enclPd=20, scsiType=0, portMap=04, sasAddr=5000c50010012e3d,0000000000000000 mfi0: 6704 (345318253s/0x0020/info) - Time established as 12/10/10 17:44:13; (50 seconds since power on) mfi0: 6705 (345318291s/0x0008/info) - Battery temperature is normal mfi0: [ITHREAD] pcib5: <ACPI PCI-PCI bridge> irq 18 at device 1.0 on pci23 pci24: <ACPI PCI bus> on pcib5 pcib6: <PCI-PCI bridge> at device 0.3 on pci22 pci26: <PCI bus> on pcib6 pcib7: <ACPI PCI-PCI bridge> irq 37 at device 3.0 on pci0 pci1: <ACPI PCI bus> on pcib7 pcib8: <ACPI PCI-PCI bridge> at device 0.0 on pci1 pci2: <ACPI PCI bus> on pcib8 pcib9: <PCI-PCI bridge> at device 1.0 on pci2 pci3: <PCI bus> on pcib9 pcib10: <ACPI PCI-PCI bridge> at device 2.0 on pci2 pci10: <ACPI PCI bus> on pcib10 pcib11: <ACPI PCI-PCI bridge> at device 0.0 on pci10 pci11: <ACPI PCI bus> on pcib11 bce0: <Broadcom NetXtreme II BCM5708 1000Base-T (B2)> mem 0xd6000000-0xd7ffffff irq 18 at device 0.0 on pci11 miibus0: <MII bus> on bce0 brgphy0: <BCM5708C 10/100/1000baseTX PHY> PHY 1 on miibus0 brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto bce0: Ethernet address: 00:26:b9:35:08:dc bce0: [ITHREAD] bce0: ASIC (0x57081020); Rev (B2); Bus (PCI-X, 64-bit, 133MHz); B/C (5.0.4); Flags (MSI|MFW); MFW (ipms 1.6.0) pcib12: <ACPI PCI-PCI bridge> at device 3.0 on pci2 pci8: <ACPI PCI bus> on pcib12 pcib13: <ACPI PCI-PCI bridge> at device 0.0 on pci8 pci9: <ACPI PCI bus> on pcib13 bce1: <Broadcom NetXtreme II BCM5708 1000Base-T (B2)> mem 0xd8000000-0xd9ffffff irq 19 at device 0.0 on pci9 miibus1: <MII bus> on bce1 brgphy1: <BCM5708C 10/100/1000baseTX PHY> PHY 1 on miibus1 brgphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto bce1: Ethernet address: 00:26:b9:35:08:da bce1: [ITHREAD] bce1: ASIC (0x57081020); Rev (B2); Bus (PCI-X, 64-bit, 133MHz); B/C (5.0.4); Flags (MSI|MFW); MFW (ipms 1.6.0) pcib14: <ACPI PCI-PCI bridge> at device 4.0 on pci2 pci6: <ACPI PCI bus> on pcib14 pcib15: <ACPI PCI-PCI bridge> at device 0.0 on pci6 pci7: <ACPI PCI bus> on pcib15 bce2: <Broadcom NetXtreme II BCM5708 1000Base-T (B2)> mem 0xda000000-0xdbffffff irq 37 at device 0.0 on pci7 miibus2: <MII bus> on bce2 brgphy2: <BCM5708C 10/100/1000baseTX PHY> PHY 1 on miibus2 brgphy2: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto bce2: Ethernet address: 00:26:b9:35:08:d8 bce2: [ITHREAD] bce2: ASIC (0x57081020); Rev (B2); Bus (PCI-X, 64-bit, 133MHz); B/C (5.0.4); Flags (MSI|MFW); MFW (UMP 1.1.9) pcib16: <ACPI PCI-PCI bridge> at device 5.0 on pci2 pci4: <ACPI PCI bus> on pcib16 pcib17: <ACPI PCI-PCI bridge> at device 0.0 on pci4 pci5: <ACPI PCI bus> on pcib17 bce3: <Broadcom NetXtreme II BCM5708 1000Base-T (B2)> mem 0xdc000000-0xddffffff irq 38 at device 0.0 on pci5 miibus3: <MII bus> on bce3 brgphy3: <BCM5708C 10/100/1000baseTX PHY> PHY 1 on miibus3 brgphy3: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto bce3: Ethernet address: 00:26:b9:35:08:d6 bce3: [ITHREAD] bce3: ASIC (0x57081020); Rev (B2); Bus (PCI-X, 64-bit, 133MHz); B/C (5.0.4); Flags (MSI|MFW); MFW (UMP 1.1.9) pcib18: <ACPI PCI-PCI bridge> irq 32 at device 4.0 on pci0 pci12: <ACPI PCI bus> on pcib18 pcib19: <ACPI PCI-PCI bridge> at device 0.0 on pci12 pci13: <ACPI PCI bus> on pcib19 pcib20: <ACPI PCI-PCI bridge> at device 2.0 on pci13 pci15: <ACPI PCI bus> on pcib20 pcib21: <ACPI PCI-PCI bridge> at device 4.0 on pci13 pci14: <ACPI PCI bus> on pcib21 pcib22: <ACPI PCI-PCI bridge> irq 33 at device 6.0 on pci0 pci16: <ACPI PCI bus> on pcib22 pcib23: <ACPI PCI-PCI bridge> at device 0.0 on pci16 pci17: <ACPI PCI bus> on pcib23 pcib24: <ACPI PCI-PCI bridge> at device 2.0 on pci17 pci19: <ACPI PCI bus> on pcib24 pcib25: <ACPI PCI-PCI bridge> at device 4.0 on pci17 pci18: <ACPI PCI bus> on pcib25 pcib26: <ACPI PCI-PCI bridge> at device 28.0 on pci0 pci21: <ACPI PCI bus> on pcib26 uhci0: <Intel 631XESB/632XESB/3100 USB controller USB-1> port 0xcc80-0xcc9f irq 20 at device 29.0 on pci0 uhci0: [ITHREAD] usbus0: <Intel 631XESB/632XESB/3100 USB controller USB-1> on uhci0 uhci1: <Intel 631XESB/632XESB/3100 USB controller USB-2> port 0xcca0-0xccbf irq 20 at device 29.1 on pci0 uhci1: [ITHREAD] usbus1: <Intel 631XESB/632XESB/3100 USB controller USB-2> on uhci1 uhci2: <Intel 631XESB/632XESB/3100 USB controller USB-3> port 0xccc0-0xccdf irq 20 at device 29.2 on pci0 uhci2: [ITHREAD] usbus2: <Intel 631XESB/632XESB/3100 USB controller USB-3> on uhci2 uhci3: <Intel 631XESB/632XESB/3100 USB controller USB-4> port 0xcce0-0xccff irq 20 at device 29.3 on pci0 uhci3: [ITHREAD] usbus3: <Intel 631XESB/632XESB/3100 USB controller USB-4> on uhci3 ehci0: <Intel 63XXESB USB 2.0 controller> mem 0xde0ffc00-0xde0fffff irq 21 at device 29.7 on pci0 ehci0: [ITHREAD] usbus4: EHCI version 1.0 usbus4: <Intel 63XXESB USB 2.0 controller> on ehci0 pcib27: <ACPI PCI-PCI bridge> at device 30.0 on pci0 pci27: <ACPI PCI bus> on pcib27 vgapci0: <VGA-compatible display> port 0xdc00-0xdcff mem 0xc8000000-0xcfffffff,0xde4f0000-0xde4fffff irq 17 at device 12.0 on pci27 isab0: <PCI-ISA bridge> at device 31.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <Intel 63XXESB2 SATA300 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xfc00-0xfc0f at device 31.2 on pci0 ata0: <ATA channel 0> on atapci0 ata0: [ITHREAD] ata1: <ATA channel 1> on atapci0 ata1: [ITHREAD] atrtc0: <AT realtime clock> port 0x70-0x7f irq 8 on acpi0 uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0 uart0: [FILTER] uart1: <16550 or compatible> port 0x2f8-0x2ff irq 3 on acpi0 uart1: [FILTER] orm0: <ISA Option ROMs> at iomem 0xc0000-0xc8fff,0xc9000-0xc9fff,0xca000-0xcbfff,0xec000-0xeffff on isa0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 kbd0 at atkbd0 atkbd0: [GIANT-LOCKED] atkbd0: [ITHREAD] ppc0: cannot reserve I/O port range est0: <Enhanced SpeedStep Frequency Control> on cpu0 est: CPU supports Enhanced Speedstep, but is not recognized. est: cpu_vendor GenuineIntel, msr 91e091e0800091e device_attach: est0 attach returned 6 p4tcc0: <CPU Frequency Thermal Control> on cpu0 est1: <Enhanced SpeedStep Frequency Control> on cpu1 est: CPU supports Enhanced Speedstep, but is not recognized. est: cpu_vendor GenuineIntel, msr 91e091e0800091e device_attach: est1 attach returned 6 p4tcc1: <CPU Frequency Thermal Control> on cpu1 est2: <Enhanced SpeedStep Frequency Control> on cpu2 est: CPU supports Enhanced Speedstep, but is not recognized. est: cpu_vendor GenuineIntel, msr 91e091e0800091e device_attach: est2 attach returned 6 p4tcc2: <CPU Frequency Thermal Control> on cpu2 est3: <Enhanced SpeedStep Frequency Control> on cpu3 est: CPU supports Enhanced Speedstep, but is not recognized. est: cpu_vendor GenuineIntel, msr 91e091e0800091e device_attach: est3 attach returned 6 p4tcc3: <CPU Frequency Thermal Control> on cpu3 est4: <Enhanced SpeedStep Frequency Control> on cpu4 est: CPU supports Enhanced Speedstep, but is not recognized. est: cpu_vendor GenuineIntel, msr 91e091e0800091e device_attach: est4 attach returned 6 p4tcc4: <CPU Frequency Thermal Control> on cpu4 est5: <Enhanced SpeedStep Frequency Control> on cpu5 est: CPU supports Enhanced Speedstep, but is not recognized. est: cpu_vendor GenuineIntel, msr 91e091e0800091e device_attach: est5 attach returned 6 p4tcc5: <CPU Frequency Thermal Control> on cpu5 est6: <Enhanced SpeedStep Frequency Control> on cpu6 est: CPU supports Enhanced Speedstep, but is not recognized. est: cpu_vendor GenuineIntel, msr 91e091e0800091e device_attach: est6 attach returned 6 p4tcc6: <CPU Frequency Thermal Control> on cpu6 est7: <Enhanced SpeedStep Frequency Control> on cpu7 est: CPU supports Enhanced Speedstep, but is not recognized. est: cpu_vendor GenuineIntel, msr 91e091e0800091e device_attach: est7 attach returned 6 p4tcc7: <CPU Frequency Thermal Control> on cpu7 est8: <Enhanced SpeedStep Frequency Control> on cpu8 est: CPU supports Enhanced Speedstep, but is not recognized. est: cpu_vendor GenuineIntel, msr 91e091e0800091e device_attach: est8 attach returned 6 p4tcc8: <CPU Frequency Thermal Control> on cpu8 est9: <Enhanced SpeedStep Frequency Control> on cpu9 est: CPU supports Enhanced Speedstep, but is not recognized. est: cpu_vendor GenuineIntel, msr 91e091e0800091e device_attach: est9 attach returned 6 p4tcc9: <CPU Frequency Thermal Control> on cpu9 est10: <Enhanced SpeedStep Frequency Control> on cpu10 est: CPU supports Enhanced Speedstep, but is not recognized. est: cpu_vendor GenuineIntel, msr 91e091e0800091e device_attach: est10 attach returned 6 p4tcc10: <CPU Frequency Thermal Control> on cpu10 est11: <Enhanced SpeedStep Frequency Control> on cpu11 est: CPU supports Enhanced Speedstep, but is not recognized. est: cpu_vendor GenuineIntel, msr 91e091e0800091e device_attach: est11 attach returned 6 p4tcc11: <CPU Frequency Thermal Control> on cpu11 est12: <Enhanced SpeedStep Frequency Control> on cpu12 est: CPU supports Enhanced Speedstep, but is not recognized. est: cpu_vendor GenuineIntel, msr 91e091e0800091e device_attach: est12 attach returned 6 p4tcc12: <CPU Frequency Thermal Control> on cpu12 est13: <Enhanced SpeedStep Frequency Control> on cpu13 est: CPU supports Enhanced Speedstep, but is not recognized. est: cpu_vendor GenuineIntel, msr 91e091e0800091e device_attach: est13 attach returned 6 p4tcc13: <CPU Frequency Thermal Control> on cpu13 est14: <Enhanced SpeedStep Frequency Control> on cpu14 est: CPU supports Enhanced Speedstep, but is not recognized. est: cpu_vendor GenuineIntel, msr 91e091e0800091e device_attach: est14 attach returned 6 p4tcc14: <CPU Frequency Thermal Control> on cpu14 est15: <Enhanced SpeedStep Frequency Control> on cpu15 est: CPU supports Enhanced Speedstep, but is not recognized. est: cpu_vendor GenuineIntel, msr 91e091e0800091e device_attach: est15 attach returned 6 p4tcc15: <CPU Frequency Thermal Control> on cpu15 Timecounters tick every 1.000 msec usbus0: 12Mbps Full Speed USB v1.0 usbus1: 12Mbps Full Speed USB v1.0 usbus2: 12Mbps Full Speed USB v1.0 usbus3: 12Mbps Full Speed USB v1.0 usbus4: 480Mbps High Speed USB v2.0 ugen0.1: <Intel> at usbus0 uhub0: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0 ugen1.1: <Intel> at usbus1 uhub1: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1 ugen2.1: <Intel> at usbus2 uhub2: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus2 ugen3.1: <Intel> at usbus3 uhub3: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus3 ugen4.1: <Intel> at usbus4 uhub4: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus4 uhub0: 2 ports with 2 removable, self powered uhub1: 2 ports with 2 removable, self powered uhub2: 2 ports with 2 removable, self powered uhub3: 2 ports with 2 removable, self powered bce0: bce_pulse(): Bootcode lost the driver pulse! (bc_state = 0x00002006) bce1: bce_pulse(): Bootcode lost the driver pulse! (bc_state = 0x00002006) bce2: bce_pulse(): Bootcode lost the driver pulse! (bc_state = 0x00004006) bce3: bce_pulse(): Bootcode lost the driver pulse! (bc_state = 0x00004006) acd0: DVDROM <TSSTcorpDVD-ROM TS-L333A/D450> at ata0-master UDMA33 SATA mfi0: 6706 (345318291s/0x0008/info) - Current capacity of the battery is above threshold mfid0: <MFI Logical Disk> on mfi0 mfid0: 953344MB (1952448512 sectors) RAID volume 'root' is optimal mfid1: <MFI Logical Disk> on mfi0 mfid1: 953344MB (1952448512 sectors) RAID volume 'storage' is optimal mfid2: <MFI Logical Disk> on mfi0 mfid2: 953344MB (1952448512 sectors) RAID volume 'ports' is optimal SMP: AP CPU #1 Launched! SMP: AP CPU #9 Launched! SMP: AP CPU #12 Launched! SMP: AP CPU #4 Launched! SMP: AP CPU #8 Launched! SMP: AP CPU #13 Launched! SMP: AP CPU #2 Launched! SMP: AP CPU #10 Launched! SMP: AP CPU #3 Launched! SMP: AP CPU #15 Launched! SMP: AP CPU #11 Launched! SMP: AP CPU #6 Launched! SMP: AP CPU #7 Launched! SMP: AP CPU #14 Launched! SMP: AP CPU #5 Launched! Root mount waiting for: usbus4 uhub4: 8 ports with 8 removable, self powered ugen4.2: <vendor 0x413c> at usbus4 uhub5: <vendor 0x413c product 0xa001, class 9/0, rev 2.00/0.00, addr 2> on usbus4 uhub5: 2 ports with 2 removable, self powered Root mount waiting for: usbus4 ugen4.3: <Dell> at usbus4 ukbd0: <Keyboard> on usbus4 kbd2 at ukbd0 ums0: <Mouse> on usbus4 ums0: 3 buttons and [Z] coordinates ID=0 ugen4.4: <vendor 0x04b4> at usbus4 uhub6: <vendor 0x04b4 product 0x6560, class 9/0, rev 2.00/90.15, addr 4> on usbus4 Root mount waiting for: usbus4 uhub6: 2 ports with 2 removable, self powered ugen1.2: <NOVATEK> at usbus1 ukbd1: <NOVATEK USB Multimedia Keyboard, class 0/0, rev 1.10/1.00, addr 2> on usbus1 kbd3 at ukbd1 uhid0: <NOVATEK USB Multimedia Keyboard, class 0/0, rev 1.10/1.00, addr 2> on usbus1 ugen4.5: <vendor 0x04b4> at usbus4 uhub7: <vendor 0x04b4 product 0x6560, class 9/0, rev 2.00/90.15, addr 5> on usbus4 uhub7: 2 ports with 2 removable, self powered Trying to mount root from ufs:/dev/mfid0s1a bce1: link state changed to UP mfi0: 6707 (345318356s/0x0008/info) - Battery started charging mfi0: 6708 (345318421s/0x0008/info) - Battery charge complete _______________________________________________ freebsd-net@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-net To unsubscribe, send any mail to "freebsd-net-unsubscr...@freebsd.org"
