Hi!
I tried it with crossover cable but results was the same bad. Then set
debug flag hw.usb.axe.debug: to 15, and started ping -f from ue0.
And in /var/log/messages I found these strings:
Jun 1 22:28:34 laptop kernel: axe_bulk_read_callback:842: bulk read
error, USB_ERR_CANCELLED
Jun 1 22:28:35 laptop kernel: axe_bulk_write_callback:870: transfer
complete
Jun 1 22:29:12 laptop kernel: axe_bulk_write_callback:941: transfer
error, USB_ERR_TIMEOUT
Jun 1 22:29:51 laptop last message repeated 4 times
Jun 1 22:31:40 laptop last message repeated 11 times
Then i googled it and found this
http://www.mail-archive.com/freebsd-...@freebsd.org/msg04388.html
the problem is described definitely like mine.
I read all thread and found the patch usb2_ethernet.patch2, but I havn't
found
sys/dev/usb2/ethernet/usb2_ethernet.c file for patch.
how can I try to apply this patch to my system?
http://www.mail-archive.com/freebsd-...@freebsd.org/msg04403.html
Thank you very mach for your help!
//
//
On 01.06.2010 03:32, Pyun YongHyeon wrote:
On Sun, May 30, 2010 at 01:16:14AM +0500, Perevalov Sergey wrote:
Pyun YongHyeon, I am really sorry, I have found you message in my spam
folder:-(
And immediately I did by your instructions.
I connected 2 Freebsd 8.0 hosts by one cable, and started tcpdump
-evvvvvvi rl0/ue0.
So, 192.168.2.15 is receiver (rl0) log: http://pastebin.com/pZ5udweh
192.168.2.16 is sender (ue0) log: http://pastebin.com/BEDwUWBe
It seems both ends does not see any frames at all. I thought axe(4)
sent wrong ethernet address to the other end but tcpdump output you
posted makes me wonder cabling issue. I'm not sure whether
rgephy(4) used in axe(4) can handle automatic MDI/MDIX crossover
but rlphy(4) surely lacks the capability. Can you retest it with
crossover cable instead of straight UTP cable?
Also your tcpdump seems to indicate both hosts are trying to send
packets. This makes it hard to know which part of NIC is not
working. Send ICMP echo request on one host(e.g. ping(8)) and
capture traffic on both sender and receiver side and post the
result again.
Thank you for your help!
On 08.05.2010 02:05, Pyun YongHyeon wrote:
On Fri, May 07, 2010 at 10:30:21PM +0500, Perevalov Sergey wrote:
Hi guys. I am beginner in FreeBSD. And I got problem with my Gigabit
usb to ethernet adapter with AX88178 chipset. It works in windows very
well but doesn't work in FreeBSD 8.0. tcpdump shows log with received
and sent packets, but any host in network doesn't receive them from it.
I checked it with 2 FreeBSD hosts connected directly by cable. Can you,
guys, advice to me something to fix or to find reason of this issue?
I started thread on freebsd forums(
http://forums.freebsd.org/showthread.php?t=13649 ) and also reported
about problem ( http://www.freebsd.org/cgi/query-pr.cgi?pr=146153 ).
It seems the PR shows tcpdump output on sender side(axe(4)
host 192.168.2.22). Would you capture the traffic on receiver side
(host 192.168.2.7) and post the result? Note, please use direct
cable to connect both systems and use option -e to capture traffic
on host 192.168.2.7. For instance, use
#ifconfig -envvvvvvi nic0
on receiver side.
Also check whether the receiver agrees on the resolved speed/duplex
of established link. For your case, host 192.168.2.7 should show
100baseTX, full-duplex.
Here some information:
dmesg:
ugen4.2:<vendor 0x0b95> at usbus4
axe0:<vendor 0x0b95 product 0x1780, rev 2.00/0.01, addr 2> on usbus4
axe0: PHYADDR 0xe0:0x02
miibus0:<MII bus> on axe0
rgephy0:<RTL8169S/8110S/8211B media interface> PHY 2 on miibus0
rgephy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
1000baseT-FDX, auto
ue0:<USB Ethernet> on axe0
ue0: Ethernet address: 00:0e:c6:88:09:4e
usbconfig:
laptop# usbconfig
ugen0.1:<UHCI root HUB Intel> at usbus0, cfg=0 md=HOST spd=FULL
(12Mbps) pwr=ON
ugen1.1:<UHCI root HUB Intel> at usbus1, cfg=0 md=HOST spd=FULL
(12Mbps) pwr=ON
ugen2.1:<UHCI root HUB Intel> at usbus2, cfg=0 md=HOST spd=FULL
(12Mbps) pwr=ON
ugen3.1:<UHCI root HUB Intel> at usbus3, cfg=0 md=HOST spd=FULL
(12Mbps) pwr=ON
ugen4.1:<EHCI root HUB Intel> at usbus4, cfg=0 md=HOST spd=HIGH
(480Mbps) pwr=ON
ugen4.2:<product 0x1780 vendor 0x0b95> at usbus4, cfg=0 md=HOST
spd=HIGH (480Mbps) pwr=ON
ugen0.2:<Optical Mouse Genius> at usbus0, cfg=0 md=HOST spd=LOW
(1.5Mbps) pwr=ON
ifconfig:
ue0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
ether 00:0e:c6:88:09:4e
inet 192.168.2.22 netmask 0xffffff00 broadcast 192.168.2.255
media: Ethernet autoselect (100baseTX<full-duplex>)
status: active
Thank you for you help!
--
Regards, Sergey.
--
Regards, Sergey.
_______________________________________________
freebsd-net@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-net
To unsubscribe, send any mail to "freebsd-net-unsubscr...@freebsd.org"
