El Miércoles, 27 de Abril de 2005 19:23, Crist J. Clark escribió:
> I want to do something rather simple, but a quick look at
> documentation ("man ppp") didn't give me an answer, and I'm
> rather pressed for time.
>
> All I want to do is send an echo-request and listen for the
> echo-reply at the PPP layer. Note that I am talking about
> pings _at the link layer,_ not IP layer pings. A quick look
> at the ppp(8) manpage didn't seem to indicate any tools for
> sending or receiving PPP-layer echoes. If ppp(8) doesn't have
> the ability, does anyone have any other _simple_ suggestions
> for doing this (e.g. dunno if it's worth writing a netgrap(4)
> node for this unless its really simple)?
>
This is FreeBSD-5.4RC3
man ppp ...
lqr
Default: Disabled and Accepted. This option decides if Link
Quality Requests will be sent or accepted. LQR is a protocol
that allows ppp to determine that the link is down without rely-
ing on the modems carrier detect. When LQR is enabled, ppp sends
the QUALPROTO option (see ``set lqrperiod'' below) as part of the
LCP request. If the peer agrees, both sides will exchange LQR
packets at the agreed frequency, allowing detailed link quality
monitoring by enabling LQM logging. If the peer doesn't agree,
and if the ``echo'' option is enabled, ppp will send LCP ECHO
requests instead. These packets pass no information of interest,
but they MUST be replied to by the peer.
Whether using LQR or LCP ECHO, ppp will abruptly drop the connec-
tion if 5 unacknowledged packets have been sent rather than send-
ing a 6th. A message is logged at the PHASE level, and any
appropriate ``reconnect'' values are honoured as if the peer were
responsible for dropping the connection.
Refer to the ``enable echo'' command description for differences
in behaviour prior to ppp version 3.4.2.
...
echo
Default: Disabled. When this option is enabled, ppp will send
LCP ECHO requests to the peer at the frequency defined by
``echoperiod''. Note, LQR requests will supersede LCP ECHO
requests if enabled and negotiated. See ``set lqrperiod'' below
for details.
Prior to ppp version 3.4.2, ``echo'' was considered enabled if
lqr was enabled and negotiated, otherwise it was considered dis-
abled. For the same behaviour, it is now necessary to ``enable
lqr echo'' rather than just ``enable lqr''.
...
echo is allways acepted, as this is part of lcp. You only need take a
look to the logs (/var/log/ppp.log, fyi).
Apr 28 07:07:14 antares ppp[785]: tun0: LCP: deflink:
RecvEchoRequest(98) state = Opened
Apr 28 07:07:14 antares ppp[785]: tun0: LCP: deflink: SendEchoReply(98)
state = Opened
Apr 28 07:07:44 antares ppp[785]: tun0: LCP: deflink:
RecvEchoRequest(99) state = Opened
Apr 28 07:07:44 antares ppp[785]: tun0: LCP: deflink: SendEchoReply(99)
state = Opened
Apr 28 07:08:15 antares ppp[785]: tun0: LCP: deflink:
RecvEchoRequest(100) state = Opened
Apr 28 07:08:15 antares ppp[785]: tun0: LCP: deflink: SendEchoReply(100)
state = Opened
Ap
--
josemi
_______________________________________________
freebsd-net@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-net
To unsubscribe, send any mail to "[EMAIL PROTECTED]"
