John Mok wrote:
The command "ngctl types" shows :-
There are 5 total types: Type name Number of living nodes --------- ---------------------- socket 1 rfc1490 0 lmi 0 frame_relay 0 sync_ar 2
What other modules are needed? How to add them, whether load them dynamically or compiled into kernel?
Thanks a lot.
kldload ng_iface at least
it should be loaded automatically if you add the line shown below..
John Mok
Julian Elischer wrote:
what does "ngctl types" say?
looks like you don't have all the right modules loaded..
John Mok wrote:
After issuing the following commands :-
#ngctl mkpeer sync_ar0: frame_relay rawdata downstream
ngctl name sync_ar0:rawdata fr-mux
replace the next line with.. #ngctl mkpeer fr-mux: lmi dlci0 ansi
and add: ngctl name fr-mux:dlci0 lmi
#ngctl mkpeer sync_ar0:rawdata rfc1490 dlci16 rfc1490
this could be replaved by: ngctl mkpeer fr-mux: rfc1490 dlci16 downstream
#ngctl mkpeer sync_ar0:rawdata dlci16 rl0 inet inet
this line is totally confused..
should be: ngctl name fr-mux:dlci16 protomux ngctl mkpeer protomux: iface inet inet
now you can add the ip addresses..
sorry I didn't read it better several days ago..
#ifconfig ng0 1.2.3.4 5.6.7.8 ifconfig: interface ng0 does not exist
are you SURE none of these returned an error?
The command ifconfig shows :-
rl0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500 options=8<VLAN_MTU> inet6 fe80::207:40ff:fe09:f09%rl0 prefixlen 64 scopeid 0x1 inet 192.168.255.254 netmask 0xffffff00 broadcast 192.168.255.255 ether 00:07:40:09:0f:09 media: Ethernet autoselect (none) status: no carrier xl0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500 options=9<RXCSUM,VLAN_MTU> inet6 fe80::201:3ff:fec1:9c58%xl0 prefixlen 64 scopeid 0x2 ether 00:01:03:c1:9c:58 media: Ethernet autoselect (100baseTX <full-duplex>) status: active xl1: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500 options=9<RXCSUM,VLAN_MTU> inet6 fe80::201:3ff:fe34:61af%xl1 prefixlen 64 scopeid 0x3 inet 192.168.16.254 netmask 0xffffff00 broadcast 192.168.16.255 ether 00:01:03:34:61:af media: Ethernet autoselect (100baseTX <full-duplex>) status: active plip0: flags=108810<POINTOPOINT,SIMPLEX,MULTICAST> mtu 1500 lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384 inet6 ::1 prefixlen 128 inet6 fe80::1%lo0 prefixlen 64 scopeid 0x5 inet 127.0.0.1 netmask 0xff000000
and the command "ngctl list" shows :-
There are 4 total nodes:
Name: ngctl811 Type: socket ID: 00000011 Num hooks: 0
Name: <unnamed> Type: frame_relay ID: 00000004 Num hooks: 1
Name: sync_ar1 Type: sync_ar ID: 00000002 Num hooks: 0
Name: sync_ar0 Type: sync_ar ID: 00000001 Num hooks: 1
Would it be the problem that I test it with cable disconnected from the modem (i.e.CSU/DSU)?
Thanks a lot.
John Mok
Julian Elischer wrote:
did the last command do anything?
please show the output of: ifconfig ngctl list
_______________________________________________ freebsd-net@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-net To unsubscribe, send any mail to "[EMAIL PROTECTED]"
