I don't know if this is the right place to ask.
I searched and googled a lot but could not find anything (execpt people with
the same problem). FreeBSD 6.2 (cvsuped to RELENG_6) is not recognizing the
pata controller on the VIA VT8237A south bridge on my ASUS P5VD2-X mobo,
dispite of the fact that I saw its id inside
src/sys/dev/ata/ata-chipset.c,v 1.126.2.19 2007/07/04 12:29:15
I have included the IDE.txt file with all the info I could get from my
machine. The pata (and sata) controller ends up identified as GENERIC.
I have only IDE drives and can get the system usable by setting
hw.ata.atapi_dma: 0
hw.ata.ata_dma: 0
Although dma is enabled in the BIOS, the drives fall back to PIO4. If set the
above to 1, FreeBSD reports them (all) at ultraDMA 33 (which, in fact worked
as ultraDMA 100 on my previous board). The system boots ok but after 7 or 10
minutes (even if doing nothing), I start geting messages from
g_vfs_done(); WRITE DMAERROR that can come from any of the drives until the
system becomes unstable and ends up rebooting itself.
Everything else works perfectly but the PIO4 mode hogs everything down !!
Any suggestions? info? direction?
Thanks,
--
**********************************************************
//| //| Mario Lobo
// |// | http://www.ipad.com.br
// // ||||||| FreeBSD since 2.2.8 - 100% Rwindows-free
**********************************************************
# lobo/root [18:08:03]
[~]>dmesg
Copyright (c) 1992-2007 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 6.2-STABLE #21: Sat Aug 4 14:48:20 BRT 2007
[EMAIL PROTECTED]:/usr/src/sys/i386/compile/LOBO
ACPI APIC Table: <AWARD ASUSACPI>
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Pentium(R) D CPU 3.20GHz (3199.66-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0xf64 Stepping = 4
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
Features2=0xe4bd<SSE3,RSVD2,MON,DS_CPL,VMX,EST,CNTX-ID,CX16,<b14>,<b15>>
AMD Features=0x20100000<NX,LM>
AMD Features2=0x1<LAHF>
Cores per package: 2
real memory = 1072562176 (1022 MB)
avail memory = 1032024064 (984 MB)
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
cpu0 (BSP): APIC ID: 0
cpu1 (AP): APIC ID: 1
ioapic0: Changing APIC ID to 4
ioapic0 <Version 0.3> irqs 0-23 on motherboard
ioapic1 <Version 0.3> irqs 24-47 on motherboard
kbd1 at kbdmux0
ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
acpi0: <AWARD ASUSACPI> on motherboard
acpi_hpet0: <High Precision Event Timer> iomem 0xfe800000-0xfe8003ff on acpi0
Timecounter "HPET" frequency 14318180 Hz quality 2000
acpi0: Power Button (fixed)
acpi0: reservation of fe800000, 100 (3) failed
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0
cpu0: <ACPI CPU> on acpi0
cpu1: <ACPI CPU> on acpi0
acpi_button0: <Power Button> on acpi0
acpi_button1: <Sleep Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <PCI-PCI bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
pcib2: <ACPI PCI-PCI bridge> irq 27 at device 2.0 on pci0
pci2: <ACPI PCI bus> on pcib2
nvidia0: <GeForce 7100 GS> mem
0xdc000000-0xdcffffff,0xc0000000-0xcfffffff,0xdd000000-0xddffffff irq 24 at
device 0.0 on pci2
nvidia0: [GIANT-LOCKED]
atapci0: <GENERIC ATA controller> port
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xfc00-0xfc0f at device 15.0 on pci0
ata0: <ATA channel 0> on atapci0
ata1: <ATA channel 1> on atapci0
uhci0: <VIA 83C572 USB controller> port 0xf800-0xf81f at device 16.0 on pci0
uhci0: [GIANT-LOCKED]
usb0: <VIA 83C572 USB controller> on uhci0
usb0: USB revision 1.0
uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <VIA 83C572 USB controller> port 0xf400-0xf41f at device 16.1 on pci0
uhci1: [GIANT-LOCKED]
usb1: <VIA 83C572 USB controller> on uhci1
usb1: USB revision 1.0
uhub1: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <VIA 83C572 USB controller> port 0xf000-0xf01f at device 16.2 on pci0
uhci2: [GIANT-LOCKED]
usb2: <VIA 83C572 USB controller> on uhci2
usb2: USB revision 1.0
uhub2: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhci3: <VIA 83C572 USB controller> port 0xec00-0xec1f at device 16.3 on pci0
uhci3: [GIANT-LOCKED]
usb3: <VIA 83C572 USB controller> on uhci3
usb3: USB revision 1.0
uhub3: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
ehci0: <VIA VT6202 USB 2.0 controller> mem 0xdffff000-0xdffff0ff at device 16.4
on pci0
ehci0: [GIANT-LOCKED]
usb4: EHCI version 1.0
usb4: companion controllers, 2 ports each: usb0 usb1 usb2 usb3
usb4: <VIA VT6202 USB 2.0 controller> on ehci0
usb4: USB revision 2.0
uhub4: VIA EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub4: 8 ports with 8 removable, self powered
isab0: <PCI-ISA bridge> at device 17.0 on pci0
isa0: <ISA bus> on isab0
pcib3: <ACPI PCI-PCI bridge> at device 19.1 on pci0
pci4: <ACPI PCI bus> on pcib3
pci4: <multimedia> at device 3.0 (no driver attached)
pcm0: <CMedia CMI8738> port 0xdc00-0xdcff irq 19 at device 5.0 on pci4
re0: <RealTek 8169SC/8110SC Single-chip Gigabit Ethernet> port 0xd800-0xd8ff
mem 0xdfeff000-0xdfeff0ff irq 20 at device 7.0 on pci4
miibus0: <MII bus> on re0
rgephy0: <RTL8169S/8110S media interface> on miibus0
rgephy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
1000baseT-FDX, auto
re0: Ethernet address: 00:1a:92:91:29:d4
re0: [FAST]
pcib4: <ACPI Host-PCI bridge> on acpi0
pci128: <ACPI PCI bus> on pcib4
acpi_tz0: <Thermal Zone> on acpi0
fdc0: <floppy drive controller> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0
fdc0: [FAST]
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
pmtimer0 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
uscanner0: Hewlett-Packard HP ScanJet 2200C, rev 1.10/1.00, addr 2
ums0: vendor 0x1241 product 0x1166, rev 1.10/2.70, addr 3, iclass 3/1
ums0: 5 buttons and Z dir.
Timecounters tick every 1.000 msec
ad0: 114498MB <SAMSUNG SP1203N TL100-23> at ata0-master PIO4
ad1: 117246MB <Maxtor 6Y120L0 YAR41VW0> at ata0-slave PIO4
ad2: 76351MB <SAMSUNG SP0802N TK100-23> at ata1-master PIO4
acd0: DVDR <HL-DT-ST DVDRAM GSA-4160B/A304> at ata1-slave PIO4
acd0: FAILURE - INQUIRY ILLEGAL REQUEST asc=0x24 ascq=0x00 sks=0x40 0x00 0x01
acd0: FAILURE - INQUIRY ILLEGAL REQUEST asc=0x24 ascq=0x00 sks=0x40 0x00 0x01
SMP: AP CPU #1 Launched!
cd0 at ata1 bus 0 target 1 lun 0
cd0: <HL-DT-ST DVDRAM GSA-4160B A304> Removable CD-ROM SCSI-0 device
cd0: 16.000MB/s transfers
------------------------------------------------------------------------------------
# lobo/root [18:08:03]
[~]>pciconf -lv
[EMAIL PROTECTED]:0:0: class=0x060000 card=0x81ce1043 chip=0x03271106
rev=0x00 hdr=0x00
vendor = 'VIA Technologies Inc'
class = bridge
subclass = HOST-PCI
[EMAIL PROTECTED]:0:1: class=0x060000 card=0x00000000 chip=0x13271106
rev=0x00 hdr=0x00
vendor = 'VIA Technologies Inc'
class = bridge
subclass = HOST-PCI
[EMAIL PROTECTED]:0:2: class=0x060000 card=0x00000000 chip=0x23271106
rev=0x00 hdr=0x00
vendor = 'VIA Technologies Inc'
class = bridge
subclass = HOST-PCI
[EMAIL PROTECTED]:0:3: class=0x060000 card=0x00000000 chip=0x33271106
rev=0x00 hdr=0x00
vendor = 'VIA Technologies Inc'
class = bridge
subclass = HOST-PCI
[EMAIL PROTECTED]:0:4: class=0x060000 card=0x00000000 chip=0x43271106
rev=0x00 hdr=0x00
vendor = 'VIA Technologies Inc'
class = bridge
subclass = HOST-PCI
[EMAIL PROTECTED]:0:5: class=0x080020 card=0x00000000 chip=0x53271106
rev=0x00 hdr=0x00
vendor = 'VIA Technologies Inc'
class = base peripheral
subclass = interrupt controller
[EMAIL PROTECTED]:0:6: class=0x060000 card=0x00000000 chip=0x63271106
rev=0x00 hdr=0x00
vendor = 'VIA Technologies Inc'
class = bridge
subclass = HOST-PCI
[EMAIL PROTECTED]:0:7: class=0x060000 card=0x00000000 chip=0x73271106
rev=0x00 hdr=0x00
vendor = 'VIA Technologies Inc'
class = bridge
subclass = HOST-PCI
[EMAIL PROTECTED]:1:0: class=0x060400 card=0x00000000 chip=0xb1981106 rev=0x00
hdr=0x01
vendor = 'VIA Technologies Inc'
device = 'ProSavageDDR P4X600 CPU to AGP Bridge'
class = bridge
subclass = PCI-PCI
[EMAIL PROTECTED]:2:0: class=0x060400 card=0xc3231106 chip=0xa3271106 rev=0x00
hdr=0x01
vendor = 'VIA Technologies Inc'
class = bridge
subclass = PCI-PCI
[EMAIL PROTECTED]:15:0: class=0x01018a card=0x81cf1043 chip=0x53371106
rev=0x07 hdr=0x00
vendor = 'VIA Technologies Inc'
class = mass storage
subclass = ATA
[EMAIL PROTECTED]:16:0: class=0x0c0300 card=0x81cf1043 chip=0x30381106
rev=0xa0 hdr=0x00
vendor = 'VIA Technologies Inc'
device = 'VT82xxxxx UHCI USB 1.1 Controller (All VIA Chipsets)'
class = serial bus
subclass = USB
[EMAIL PROTECTED]:16:1: class=0x0c0300 card=0x81cf1043 chip=0x30381106
rev=0xa0 hdr=0x00
vendor = 'VIA Technologies Inc'
device = 'VT82xxxxx UHCI USB 1.1 Controller (All VIA Chipsets)'
class = serial bus
subclass = USB
[EMAIL PROTECTED]:16:2: class=0x0c0300 card=0x81cf1043 chip=0x30381106
rev=0xa0 hdr=0x00
vendor = 'VIA Technologies Inc'
device = 'VT82xxxxx UHCI USB 1.1 Controller (All VIA Chipsets)'
class = serial bus
subclass = USB
[EMAIL PROTECTED]:16:3: class=0x0c0300 card=0x81cf1043 chip=0x30381106
rev=0xa0 hdr=0x00
vendor = 'VIA Technologies Inc'
device = 'VT82xxxxx UHCI USB 1.1 Controller (All VIA Chipsets)'
class = serial bus
subclass = USB
[EMAIL PROTECTED]:16:4: class=0x0c0320 card=0x81cf1043 chip=0x31041106
rev=0x86 hdr=0x00
vendor = 'VIA Technologies Inc'
device = 'VT6202 USB 2.0 Enhanced Host Controller'
class = serial bus
subclass = USB
[EMAIL PROTECTED]:17:0: class=0x060100 card=0x81cf1043 chip=0x33371106
rev=0x00 hdr=0x00
vendor = 'VIA Technologies Inc'
class = bridge
subclass = PCI-ISA
[EMAIL PROTECTED]:17:7: class=0x060000 card=0x337e1106 chip=0x287e1106
rev=0x00 hdr=0x00
vendor = 'VIA Technologies Inc'
class = bridge
subclass = HOST-PCI
[EMAIL PROTECTED]:19:0: class=0x060000 card=0x00000000 chip=0x337b1106
rev=0x00 hdr=0x00
vendor = 'VIA Technologies Inc'
class = bridge
subclass = HOST-PCI
[EMAIL PROTECTED]:19:1: class=0x060401 card=0x337a1106 chip=0x337a1106
rev=0x00 hdr=0x01
vendor = 'VIA Technologies Inc'
class = bridge
subclass = PCI-PCI
[EMAIL PROTECTED]:0:0: class=0x030000 card=0x22341682 chip=0x016a10de
rev=0xa1 hdr=0x00
vendor = 'NVIDIA Corporation'
class = display
subclass = VGA
[EMAIL PROTECTED]:3:0: class=0x048000 card=0x0020ecc0 chip=0x18011057 rev=0x02
hdr=0x00
vendor = 'Motorola'
device = 'DSP56301 24-bit Digital Signal Processor'
class = multimedia
[EMAIL PROTECTED]:5:0: class=0x040100 card=0x011113f6 chip=0x011113f6 rev=0x10
hdr=0x00
vendor = 'C-Media Electronics Inc.'
device = 'CMI8738/PCI C3DX It´s uses YMF744-B-V remarked chip'
class = multimedia
subclass = audio
[EMAIL PROTECTED]:7:0: class=0x020000 card=0x816710ec chip=0x816710ec
rev=0x10 hdr=0x00
vendor = 'Realtek Semiconductor'
class = network
subclass = ethernet
------------------------------------------------------------------------------------
# lobo/root [18:08:03]
[~]>atacontrol list
ATA channel 0:
Master: ad0 <SAMSUNG SP1203N/TL100-23> ATA/ATAPI revision 7
Slave: ad1 <Maxtor 6Y120L0/YAR41VW0> ATA/ATAPI revision 7
ATA channel 1:
Master: ad2 <SAMSUNG SP0802N/TK100-23> ATA/ATAPI revision 7
Slave: acd0 <HL-DT-ST DVDRAM GSA-4160B/A304> ATA/ATAPI revision 5
------------------------------------------------------------------------------------
# lobo/root [18:08:03]
[~]>atacontrol cap ad0
Protocol ATA/ATAPI revision 7
device model SAMSUNG SP1203N
serial number 0752J1FW943928
firmware revision TL100-23
cylinders 16383
heads 16
sectors/track 63
lba supported 234493056 sectors
lba48 supported 234493056 sectors
dma supported
overlap not supported
Feature Support Enable Value Vendor
write cache yes yes
read ahead yes yes
Tagged Command Queuing (TCQ) no no 0/0x00
SMART yes no
microcode download yes yes
security yes no
power management yes yes
advanced power management no no 0/0x00
automatic acoustic management yes no 0/0x00 254/0xFE
------------------------------------------------------------------------------------
# lobo/root [18:08:03]
[~]>atacontrol cap ad1
Protocol ATA/ATAPI revision 7
device model Maxtor 6Y120L0
serial number Y41PW1VE
firmware revision YAR41VW0
cylinders 16383
heads 16
sectors/track 63
lba supported 240121728 sectors
lba48 not supported
dma supported
overlap not supported
Feature Support Enable Value Vendor
write cache yes yes
read ahead yes yes
Tagged Command Queuing (TCQ) no no 0/0x00
SMART yes no
microcode download yes yes
security yes no
power management yes yes
advanced power management yes no 0/0x00
automatic acoustic management yes no 0/0x00 192/0xC0
------------------------------------------------------------------------------------
# lobo/root [18:08:03]
[~]>atacontrol cap ad2
Protocol ATA/ATAPI revision 7
device model SAMSUNG SP0802N
serial number 0637J1FW598953
firmware revision TK100-23
cylinders 16383
heads 16
sectors/track 63
lba supported 156368016 sectors
lba48 supported 156368016 sectors
dma supported
overlap not supported
Feature Support Enable Value Vendor
write cache yes yes
read ahead yes yes
Tagged Command Queuing (TCQ) no no 0/0x00
SMART yes no
microcode download yes yes
security yes no
power management yes yes
advanced power management no no 0/0x00
automatic acoustic management yes no 0/0x00 254/0xFE
------------------------------------------------------------------------------------
# lobo/root [18:08:03]
[~]>atacontrol cap acd0
Protocol ATA/ATAPI revision 5
device model HL-DT-ST DVDRAM GSA-4160B
serial number K7G498E1619
firmware revision A304
cylinders 0
heads 0
sectors/track 0
lba supported
lba48 not supported
dma supported
overlap not supported
Feature Support Enable Value Vendor
write cache no no
read ahead no no
Tagged Command Queuing (TCQ) no no 0/0x00
SMART no no
microcode download no no
security no no
power management yes no
advanced power management no no 0/0x00
automatic acoustic management no no 0/0x00 0/0x00
------------------------------------------------------------------------------------
Copyright (c) 1992-2007 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 6.2-STABLE #21: Sat Aug 4 14:48:20 BRT 2007
[EMAIL PROTECTED]:/usr/src/sys/i386/compile/LOBO
Preloaded elf kernel "/boot/kernel/kernel" at 0xc10d8000.
Preloaded elf module "/boot/kernel/sound.ko" at 0xc10d8188.
Preloaded elf module "/boot/kernel/snd_cmi.ko" at 0xc10d8234.
Preloaded elf module "/boot/kernel/acpi_video.ko" at 0xc10d82e0.
Preloaded elf module "/boot/kernel/acpi.ko" at 0xc10d8390.
Preloaded elf module "/boot/kernel/acpi_asus.ko" at 0xc10d843c.
Preloaded elf module "/boot/modules/nvidia.ko" at 0xc10d84ec.
Preloaded elf module "/boot/kernel/linux.ko" at 0xc10d8598.
MP Configuration Table version 1.4 found at 0xc00f1400
Table 'FACP' at 0x3feeac80
Table 'HPET' at 0x3feeaec0
Table 'MCFG' at 0x3feeaf40
Table 'APIC' at 0x3feeadc0
MADT: Found table at 0x3feeadc0
APIC: Using the MADT enumerator.
MADT: Found CPU APIC ID 0 ACPI ID 0: enabled
SMP: Added CPU 0 (AP)
MADT: Found CPU APIC ID 1 ACPI ID 1: enabled
SMP: Added CPU 1 (AP)
MADT: Found CPU APIC ID 2 ACPI ID 2: disabled
MADT: Found CPU APIC ID 3 ACPI ID 3: disabled
INTR: Adding local APIC 0 as a target
ACPI APIC Table: <AWARD ASUSACPI>
Calibrating clock(s) ... i8254 clock: 1193222 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz quality 0
Calibrating TSC clock ... TSC clock: 3199659120 Hz
CPU: Intel(R) Pentium(R) D CPU 3.20GHz (3199.66-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0xf64 Stepping = 4
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
Features2=0xe4bd<SSE3,RSVD2,MON,DS_CPL,VMX,EST,CNTX-ID,CX16,<b14>,<b15>>
AMD Features=0x20100000<NX,LM>
AMD Features2=0x1<LAHF>
Cores per package: 2
real memory = 1072562176 (1022 MB)
Physical memory chunk(s):
0x0000000000001000 - 0x000000000009dfff, 643072 bytes (157 pages)
0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages)
0x0000000001428000 - 0x000000003ec9cfff, 1032278016 bytes (252021 pages)
avail memory = 1032024064 (984 MB)
INTR: Adding local APIC 1 as a target
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
cpu0 (BSP): APIC ID: 0
cpu1 (AP): APIC ID: 1
bios32: Found BIOS32 Service Directory header at 0xc00fb780
bios32: Entry = 0xf1d70 (c00f1d70) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0xf0000+0x1da0
pnpbios: Found PnP BIOS data at 0xc00fc2d0
pnpbios: Entry = f0000:c300 Rev = 1.0
Other BIOS signatures found:
APIC: CPU 0 has ACPI ID 0
APIC: CPU 1 has ACPI ID 1
MADT: Found IO APIC ID 4, Interrupt 0 at 0xfec00000
ioapic0: Changing APIC ID to 4
ioapic0: Routing external 8259A's -> intpin 0
MADT: Found IO APIC ID 5, Interrupt 24 at 0xfecc0000
MADT: Interrupt override: source 0, irq 2
ioapic0: Routing IRQ 0 -> intpin 2
MADT: Interrupt override: source 9, irq 9
ioapic0: intpin 9 trigger: level
ioapic0: intpin 9 polarity: low
lapic0: Routing NMI -> LINT1
lapic0: LINT1 trigger: edge
lapic0: LINT1 polarity: high
lapic1: Routing NMI -> LINT1
lapic1: LINT1 trigger: edge
lapic1: LINT1 polarity: high
MADT: Ignoring local NMI routed to ACPI CPU 2
MADT: Ignoring local NMI routed to ACPI CPU 3
ioapic0 <Version 0.3> irqs 0-23 on motherboard
ioapic1 <Version 0.3> irqs 24-47 on motherboard
cpu0 BSP:
ID: 0x00000000 VER: 0x00050014 LDR: 0x00000000 DFR: 0xffffffff
lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
timer: 0x000100ef therm: 0x00010000 err: 0x00010000 pcm: 0x00010000
ath_rate: version 1.2 <SampleRate bit-rate selection algorithm>
wlan: <802.11 Link Layer>
kbd: new array size 4
kbd1 at kbdmux0
mem: <memory>
Pentium Pro MTRR support enabled
null: <null device, zero device>
io: <I/O>
random: <entropy source, Software, Yarrow>
VESA: information block
56 45 53 41 00 03 00 01 00 01 01 00 00 00 22 00
00 01 00 10 44 05 07 01 00 01 1a 01 00 01 30 01
00 01 00 01 01 01 02 01 03 01 04 01 05 01 06 01
07 01 0e 01 0f 01 11 01 12 01 14 01 15 01 17 01
VESA: 32 mode(s) found
VESA: v3.0, 262144k memory, flags:0x1, mode table:0xc08a9782 (1000022)
VESA: NVIDIA
VESA: NVIDIA Corporation nv44 Board - p280h9 Chip Rev
ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
npx0: INT 16 interface
acpi0: <AWARD ASUSACPI> on motherboard
ioapic0: routing intpin 9 (ISA IRQ 9) to vector 48
acpi0: [MPSAFE]
acpi_hpet0: <High Precision Event Timer> iomem 0xfe800000-0xfe8003ff on acpi0
acpi_hpet0: vend: 0x1106 rev: 0x1 num: 1 hz: 14318180 opts: leg_route
Timecounter "HPET" frequency 14318180 Hz quality 2000
pci_open(1): mode 1 addr port (0x0cf8) is 0x80007804
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=80] is there (id=03271106)
pcibios: BIOS version 3.00
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: \\_SB_.PCI0.VT86.VTSB -> bus 0 dev 17 func 0
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: \\_SB_.PCI0.P2PE.P2ER -> bus 0 dev 19 func 0
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: \\_SB_.PCI0.SBF7.SBVL -> bus 0 dev 17 func 7
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: \\_SB_.PCI0.SATA.SAPR -> bus 0 dev 15 func 0
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: \\_SB_.PCI0.PATA.PAPR -> bus 0 dev 15 func 1
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: \\_SB_.PCI0.USB1.U2F0 -> bus 0 dev 16 func 0
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: \\_SB_.PCI0.USB2.U2F1 -> bus 0 dev 16 func 1
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: \\_SB_.PCI0.USB3.U2F2 -> bus 0 dev 16 func 2
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: \\_SB_.PCI0.USB4.U2F3 -> bus 0 dev 16 func 3
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: \\_SB_.PCI0.EHCI.U2F4 -> bus 0 dev 16 func 4
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: \\_SB_.PCI0.PEXG.RPXG -> bus 0 dev 2 func 0
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: \\_SB_.PCI0.PEX0.RPX0 -> bus 0 dev 3 func 0
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: \\_SB_.PCI0.PEX1.RPX1 -> bus 0 dev 3 func 1
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: \\_SB_.PCI0.PEX2.RPX2 -> bus 0 dev 3 func 2
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: \\_SB_.PCI0.PEX3.RPX3 -> bus 0 dev 3 func 3
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: \\_SB_.PCI0.P2PB.P2PR -> bus 0 dev 19 func 1
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: \\_SB_.PCI1.PE5C.PE5R -> bus 0 dev 0 func 0
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: \\_SB_.PCI1.PE6C.PE6R -> bus 0 dev 0 func 1
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: \\_SB_.PCI1.AZAC.AZAR -> bus 0 dev 1 func 0
acpi0: Power Button (fixed)
acpi0: wakeup code va 0xd9280000 pa 0x9d000
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: \\_SB_.PCI0.P2PE.PE5C.PE5R -> bus 0 dev 0 func 0
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: \\_SB_.PCI0.P2PE.PE6C.PE6R -> bus 0 dev 0 func 1
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: \\_SB_.PCI0.P2PE.AZAC.AZAR -> bus 0 dev 1 func 0
acpi0: reservation of fe800000, 100 (3) failed
ACPI timer: 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 -> 10
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0
pci_link0: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 6 7 10 11 12
Validation 0 255 N 0 3 4 6 7 10 11 12
After Disable 0 255 N 0 3 4 6 7 10 11 12
pci_link1: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 6 7 10 11 12
Validation 0 255 N 0 3 4 6 7 10 11 12
After Disable 0 255 N 0 3 4 6 7 10 11 12
pci_link2: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 6 7 10 11 12
Validation 0 255 N 0 3 4 6 7 10 11 12
After Disable 0 255 N 0 3 4 6 7 10 11 12
pci_link3: Index IRQ Rtd Ref IRQs
Initial Probe 0 5 N 0 3 4 6 7 10 11 12
Validation 0 255 N 0 3 4 6 7 10 11 12
After Disable 0 255 N 0 3 4 6 7 10 11 12
pci_link4: Index IRQ Rtd Ref IRQs
Initial Probe 0 11 N 0 3 4 6 7 10 11 12
Validation 0 11 N 0 3 4 6 7 10 11 12
After Disable 0 255 N 0 3 4 6 7 10 11 12
pci_link5: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 6 7 10 11 12
Validation 0 255 N 0 3 4 6 7 10 11 12
After Disable 0 255 N 0 3 4 6 7 10 11 12
pci_link6: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 6 7 10 11 12
Validation 0 255 N 0 3 4 6 7 10 11 12
After Disable 0 255 N 0 3 4 6 7 10 11 12
pci_link7: Index IRQ Rtd Ref IRQs
Initial Probe 0 10 N 0 3 4 6 7 10 11 12
Validation 0 10 N 0 3 4 6 7 10 11 12
After Disable 0 255 N 0 3 4 6 7 10 11 12
cpu0: <ACPI CPU> on acpi0
cpu0: switching to generic Cx mode
cpu1: <ACPI CPU> on acpi0
acpi_button0: <Power Button> on acpi0
acpi_button1: <Sleep Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pci0: physical bus=0
found-> vendor=0x1106, dev=0x0327, revid=0x00
bus=0, slot=0, func=0
class=06-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x2210, cachelnsz=0 (dwords)
lattimer=0x08 (240 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
powerspec 2 supports D0 D3 current D0
map[10]: type 3, range 32, base d0000000, size 27, memory disabled
found-> vendor=0x1106, dev=0x1327, revid=0x00
bus=0, slot=0, func=1
class=06-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0006, statreg=0x0200, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1106, dev=0x2327, revid=0x00
bus=0, slot=0, func=2
class=06-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0006, statreg=0x0200, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1106, dev=0x3327, revid=0x00
bus=0, slot=0, func=3
class=06-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0006, statreg=0x0200, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1106, dev=0x4327, revid=0x00
bus=0, slot=0, func=4
class=06-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0006, statreg=0x0200, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1106, dev=0x5327, revid=0x00
bus=0, slot=0, func=5
class=08-00-20, hdrtype=0x00, mfdev=1
cmdreg=0x0006, statreg=0x0000, cachelnsz=8 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1106, dev=0x6327, revid=0x00
bus=0, slot=0, func=6
class=06-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0006, statreg=0x0000, cachelnsz=8 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1106, dev=0x7327, revid=0x00
bus=0, slot=0, func=7
class=06-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0006, statreg=0x0200, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1106, dev=0xb198, revid=0x00
bus=0, slot=1, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0007, statreg=0x0230, cachelnsz=8 (dwords)
lattimer=0x00 (0 ns), mingnt=0x14 (5000 ns), maxlat=0x00 (0 ns)
powerspec 2 supports D0 D3 current D0
found-> vendor=0x1106, dev=0xa327, revid=0x00
bus=0, slot=2, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0007, statreg=0x0010, cachelnsz=8 (dwords)
lattimer=0x00 (0 ns), mingnt=0x0c (3000 ns), maxlat=0x00 (0 ns)
intpin=a, irq=10
powerspec 2 supports D0 D3 current D0
MSI supports 1 message, 64 bit, vector masks
pcib0: matched entry for 0.2.INTA
pcib0: slot 2 INTA hardwired to IRQ 27
found-> vendor=0x1106, dev=0x5337, revid=0x07
bus=0, slot=15, func=0
class=01-01-8a, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
powerspec 2 supports D0 D3 current D0
map[20]: type 4, range 32, base 0000fc00, size 4, enabled
found-> vendor=0x1106, dev=0x3038, revid=0xa0
bus=0, slot=16, func=0
class=0c-03-00, hdrtype=0x00, mfdev=1
cmdreg=0x0007, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=255
powerspec 2 supports D0 D1 D2 D3 current D0
map[20]: type 4, range 32, base 0000f800, size 5, enabled
found-> vendor=0x1106, dev=0x3038, revid=0xa0
bus=0, slot=16, func=1
class=0c-03-00, hdrtype=0x00, mfdev=1
cmdreg=0x0007, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=b, irq=255
powerspec 2 supports D0 D1 D2 D3 current D0
map[20]: type 4, range 32, base 0000f400, size 5, enabled
found-> vendor=0x1106, dev=0x3038, revid=0xa0
bus=0, slot=16, func=2
class=0c-03-00, hdrtype=0x00, mfdev=1
cmdreg=0x0007, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=c, irq=255
powerspec 2 supports D0 D1 D2 D3 current D0
map[20]: type 4, range 32, base 0000f000, size 5, enabled
found-> vendor=0x1106, dev=0x3038, revid=0xa0
bus=0, slot=16, func=3
class=0c-03-00, hdrtype=0x00, mfdev=1
cmdreg=0x0007, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=d, irq=255
powerspec 2 supports D0 D1 D2 D3 current D0
map[20]: type 4, range 32, base 0000ec00, size 5, enabled
found-> vendor=0x1106, dev=0x3104, revid=0x86
bus=0, slot=16, func=4
class=0c-03-20, hdrtype=0x00, mfdev=1
cmdreg=0x0007, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=c, irq=255
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 1, range 32, base dffff000, size 8, enabled
found-> vendor=0x1106, dev=0x3337, revid=0x00
bus=0, slot=17, func=0
class=06-01-00, hdrtype=0x00, mfdev=1
cmdreg=0x0003, statreg=0x0210, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
powerspec 2 supports D0 D3 current D0
found-> vendor=0x1106, dev=0x287e, revid=0x00
bus=0, slot=17, func=7
class=06-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0000, statreg=0x2210, cachelnsz=0 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1106, dev=0x337b, revid=0x00
bus=0, slot=19, func=0
class=06-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0007, statreg=0x2010, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1106, dev=0x337a, revid=0x00
bus=0, slot=19, func=1
class=06-04-01, hdrtype=0x01, mfdev=0
cmdreg=0x0007, statreg=0x2010, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0 ns)
pcib1: <PCI-PCI bridge> at device 1.0 on pci0
pcib1: secondary bus 1
pcib1: subordinate bus 1
pcib1: I/O decode 0xf000-0xfff
pcib1: memory decode 0xfff00000-0xfffff
pcib1: prefetched decode 0xfff00000-0xfffff
pci1: <PCI bus> on pcib1
pci1: physical bus=1
pcib2: <ACPI PCI-PCI bridge> irq 27 at device 2.0 on pci0
pcib2: secondary bus 2
pcib2: subordinate bus 2
pcib2: I/O decode 0xf000-0xfff
pcib2: memory decode 0xdc000000-0xdeffffff
pcib2: prefetched decode 0xc0000000-0xcfffffff
pci2: <ACPI PCI bus> on pcib2
pci2: physical bus=2
found-> vendor=0x10de, dev=0x016a, revid=0xa1
bus=2, slot=0, func=0
class=03-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0010, cachelnsz=8 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=10
powerspec 2 supports D0 D3 current D0
MSI supports 1 message, 64 bit
map[10]: type 1, range 32, base dc000000, size 24, enabled
pcib2: requested memory range 0xdc000000-0xdcffffff: good
map[14]: type 3, range 64, base c0000000, size 28, enabled
pcib2: requested memory range 0xc0000000-0xcfffffff: good
map[1c]: type 1, range 64, base dd000000, size 24, enabled
pcib2: requested memory range 0xdd000000-0xddffffff: good
pcib2: matched entry for 2.0.INTA
pcib2: slot 0 INTA hardwired to IRQ 24
nvidia0: <GeForce 7100 GS> mem
0xdc000000-0xdcffffff,0xc0000000-0xcfffffff,0xdd000000-0xddffffff irq 24 at
device 0.0 on pci2
nvidia0: Reserved 0x1000000 bytes for rid 0x10 type 3 at 0xdc000000
nvidia0: Reserved 0x10000000 bytes for rid 0x14 type 3 at 0xc0000000
nvidia0: Reserved 0x1000000 bytes for rid 0x1c type 3 at 0xdd000000
ioapic1: routing intpin 0 (PCI IRQ 24) to vector 49
nvidia0: [GIANT-LOCKED]
atapci0: <GENERIC ATA controller> port
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xfc00-0xfc0f at device 15.0 on pci0
atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0xfc00
ata0: <ATA channel 0> on atapci0
atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0
atapci0: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6
ata0: reset tp1 mask=03 ostat0=50 ostat1=50
ata0: stat0=0x50 err=0x01 lsb=0x00 msb=0x00
ata0: stat1=0x50 err=0x01 lsb=0x00 msb=0x00
ata0: reset tp2 stat0=50 stat1=50 devices=0x3<ATA_SLAVE,ATA_MASTER>
ioapic0: routing intpin 14 (ISA IRQ 14) to vector 50
ata0: [MPSAFE]
ata1: <ATA channel 1> on atapci0
atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170
atapci0: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376
ata1: reset tp1 mask=03 ostat0=50 ostat1=00
ata1: stat0=0x50 err=0x01 lsb=0x00 msb=0x00
ata1: stat1=0x00 err=0x01 lsb=0x14 msb=0xeb
ata1: reset tp2 stat0=50 stat1=00 devices=0x9<ATAPI_SLAVE,ATA_MASTER>
ioapic0: routing intpin 15 (ISA IRQ 15) to vector 51
ata1: [MPSAFE]
uhci0: <VIA 83C572 USB controller> port 0xf800-0xf81f at device 16.0 on pci0
uhci0: Reserved 0x20 bytes for rid 0x20 type 4 at 0xf800
pcib0: matched entry for 0.16.INTA
pcib0: slot 16 INTA hardwired to IRQ 20
ioapic0: routing intpin 20 (PCI IRQ 20) to vector 52
uhci0: [GIANT-LOCKED]
usb0: <VIA 83C572 USB controller> on uhci0
usb0: USB revision 1.0
uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <VIA 83C572 USB controller> port 0xf400-0xf41f at device 16.1 on pci0
uhci1: Reserved 0x20 bytes for rid 0x20 type 4 at 0xf400
pcib0: matched entry for 0.16.INTB
pcib0: slot 16 INTB hardwired to IRQ 22
ioapic0: routing intpin 22 (PCI IRQ 22) to vector 53
uhci1: [GIANT-LOCKED]
usb1: <VIA 83C572 USB controller> on uhci1
usb1: USB revision 1.0
uhub1: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <VIA 83C572 USB controller> port 0xf000-0xf01f at device 16.2 on pci0
uhci2: Reserved 0x20 bytes for rid 0x20 type 4 at 0xf000
pcib0: matched entry for 0.16.INTC
pcib0: slot 16 INTC hardwired to IRQ 21
ioapic0: routing intpin 21 (PCI IRQ 21) to vector 54
uhci2: [GIANT-LOCKED]
usb2: <VIA 83C572 USB controller> on uhci2
usb2: USB revision 1.0
uhub2: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhci3: <VIA 83C572 USB controller> port 0xec00-0xec1f at device 16.3 on pci0
uhci3: Reserved 0x20 bytes for rid 0x20 type 4 at 0xec00
pcib0: matched entry for 0.16.INTD
pcib0: slot 16 INTD hardwired to IRQ 23
ioapic0: routing intpin 23 (PCI IRQ 23) to vector 55
uhci3: [GIANT-LOCKED]
usb3: <VIA 83C572 USB controller> on uhci3
usb3: USB revision 1.0
uhub3: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
ehci0: <VIA VT6202 USB 2.0 controller> mem 0xdffff000-0xdffff0ff at device 16.4
on pci0
ehci0: Reserved 0x100 bytes for rid 0x10 type 3 at 0xdffff000
pcib0: matched entry for 0.16.INTC
pcib0: slot 16 INTC hardwired to IRQ 21
ehci0: [GIANT-LOCKED]
ehci0: Dropped interrupts workaround enabled
usb4: EHCI version 1.0
usb4: companion controllers, 2 ports each: usb0 usb1 usb2 usb3
usb4: <VIA VT6202 USB 2.0 controller> on ehci0
usb4: USB revision 2.0
uhub4: VIA EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub4: 8 ports with 8 removable, self powered
isab0: <PCI-ISA bridge> at device 17.0 on pci0
isa0: <ISA bus> on isab0
pcib3: <ACPI PCI-PCI bridge> at device 19.1 on pci0
pcib3: secondary bus 4
pcib3: subordinate bus 4
pcib3: I/O decode 0xd000-0xdfff
pcib3: memory decode 0xdfe00000-0xdfefffff
pcib3: prefetched decode 0xfff00000-0xfffff
pcib3: Subtractively decoded bridge.
pci4: <ACPI PCI bus> on pcib3
pci4: physical bus=4
found-> vendor=0x1057, dev=0x1801, revid=0x02
bus=4, slot=3, func=0
class=04-80-00, hdrtype=0x00, mfdev=0
cmdreg=0x0006, statreg=0x0280, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=255
map[10]: type 1, range 32, base dfee0000, size 16, enabled
pcib3: requested memory range 0xdfee0000-0xdfeeffff: good
found-> vendor=0x13f6, dev=0x0111, revid=0x10
bus=4, slot=5, func=0
class=04-01-00, hdrtype=0x00, mfdev=0
cmdreg=0x0085, statreg=0x0210, cachelnsz=0 (dwords)
lattimer=0x20 (960 ns), mingnt=0x02 (500 ns), maxlat=0x18 (6000 ns)
intpin=a, irq=5
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 4, range 32, base 0000dc00, size 8, enabled
pcib3: requested I/O range 0xdc00-0xdcff: in range
pcib3: matched entry for 4.5.INTA
pcib3: slot 5 INTA hardwired to IRQ 19
found-> vendor=0x10ec, dev=0x8167, revid=0x10
bus=4, slot=7, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x02b0, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x20 (8000 ns), maxlat=0x40 (16000 ns)
intpin=a, irq=11
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 4, range 32, base 0000d800, size 8, enabled
pcib3: requested I/O range 0xd800-0xd8ff: in range
map[14]: type 1, range 32, base dfeff000, size 8, enabled
pcib3: requested memory range 0xdfeff000-0xdfeff0ff: good
pcib3: matched entry for 4.7.INTA
pcib3: slot 7 INTA hardwired to IRQ 20
pci4: <multimedia> at device 3.0 (no driver attached)
pcm0: <CMedia CMI8738> port 0xdc00-0xdcff irq 19 at device 5.0 on pci4
pcm0: Reserved 0x100 bytes for rid 0x10 type 4 at 0xdc00
ioapic0: routing intpin 19 (PCI IRQ 19) to vector 56
pcm0: [MPSAFE]
pcm0: Mixer "vol":
pcm0: Mixer "bass":
pcm0: Mixer "treble":
pcm0: Mixer "synth":
pcm0: Mixer "pcm":
pcm0: Mixer "speaker":
pcm0: Mixer "line":
pcm0: Mixer "mic":
pcm0: Mixer "cd":
pcm0: Mixer "igain":
pcm0: Mixer "ogain":
pcm0: Mixer "monitor":
pcm0: sndbuf_setmap 3e8d0000, 4000; 0xe57a3000 -> 3e8d0000
pcm0: sndbuf_setmap 3e8cc000, 4000; 0xe57a7000 -> 3e8cc000
re0: Reserved 0x100 bytes for rid 0x10 type 4 at 0xd800
pcib3: re0 requested I/O range 0xd800-0xd8ff: in range
re0: <RealTek 8169SC/8110SC Single-chip Gigabit Ethernet> port 0xd800-0xd8ff
mem 0xdfeff000-0xdfeff0ff irq 20 at device 7.0 on pci4
pcib3: re0 requested I/O range 0xd800-0xd8ff: in range
miibus0: <MII bus> on re0
rgephy0: <RTL8169S/8110S media interface> on miibus0
rgephy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
1000baseT-FDX, auto
re0: bpf attached
re0: Ethernet address: 00:1a:92:91:29:d4
re0: [MPSAFE]
re0: [FAST]
pcib4: <ACPI Host-PCI bridge> on acpi0
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: \\_SB_.PCI0.VT86.BDRE -> bus 0 dev 17 func 0
pci128: <ACPI PCI bus> on pcib4
pci128: physical bus=128
acpi_tz0: <Thermal Zone> on acpi0
fdc0: <floppy drive controller> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0
fdc0: ic_type 90 part_id 80
ioapic0: routing intpin 6 (ISA IRQ 6) to vector 57
fdc0: [MPSAFE]
fdc0: [FAST]
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0: irq maps: 0xc061 0xc061 0xc061 0xc061
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A
ioapic0: routing intpin 4 (ISA IRQ 4) to vector 58
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0067
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000
ioapic0: routing intpin 1 (ISA IRQ 1) to vector 59
atkbd0: [GIANT-LOCKED]
psm0: unable to allocate IRQ
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
atkbdc: atkbdc0 already exists; skipping it
fdc: fdc0 already exists; skipping it
sio: sio0 already exists; skipping it
pnp_identify: Trying Read_Port at 203
pnp_identify: Trying Read_Port at 243
pnp_identify: Trying Read_Port at 283
pnp_identify: Trying Read_Port at 2c3
pnp_identify: Trying Read_Port at 303
pnp_identify: Trying Read_Port at 343
pnp_identify: Trying Read_Port at 383
pnp_identify: Trying Read_Port at 3c3
PNP Identify complete
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
ex_isa_identify()
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
pmtimer0 on isa0
adv0: not probed (disabled)
aha0: not probed (disabled)
aic0: not probed (disabled)
bt0: not probed (disabled)
cs0: not probed (disabled)
ed0: not probed (disabled)
fe0: not probed (disabled)
ie0: not probed (disabled)
lnc0: not probed (disabled)
mpu0 failed to probe at port 0x300 irq 5 on isa0
ppc0 failed to probe at irq 7 on isa0
fb: new array size 4
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd1, terminal emulator: sc (syscons terminal)
sn0: not probed (disabled)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
vt0: not probed (disabled)
isa_probe_children: probing PnP devices
uscanner0: Hewlett-Packard HP ScanJet 2200C, rev 1.10/1.00, addr 2
ums0: vendor 0x1241 product 0x1166, rev 1.10/2.70, addr 3, iclass 3/1
ums0: 5 buttons and Z dir.
Device configuration finished.
procfs registered
lapic: Divisor 2, Frequency 99989344 hz
Timecounter "TSC" frequency 3199659120 Hz quality -100
Timecounters tick every 1.000 msec
Linux ELF exec handler installed
lo0: bpf attached
ata0-slave: pio=PIO4 wdma=WDMA2 udma=UDMA133 cable=80 wire
ata0-master: pio=PIO4 wdma=WDMA2 udma=UDMA100 cable=80 wire
ad0: 114498MB <SAMSUNG SP1203N TL100-23> at ata0-master PIO4
ad0: 234493056 sectors [232632C/16H/63S] 16 sectors/interrupt 1 depth queue
ad0: VIA check1 failed
ad0: Adaptec check1 failed
ad0: LSI (v3) check1 failed
ad0: LSI (v2) check1 failed
ad0: FreeBSD check1 failed
ad1: 117246MB <Maxtor 6Y120L0 YAR41VW0> at ata0-slave PIO4
ad1: 240121728 sectors [238216C/16H/63S] 16 sectors/interrupt 1 depth queue
ad1: VIA check1 failed
ad1: Adaptec check1 failed
ad1: LSI (v3) check1 failed
ad1: LSI (v2) check1 failed
ad1: FreeBSD check1 failed
ata1-slave: pio=PIO4 wdma=WDMA2 udma=UDMA66 cable=80 wire
ata1-master: pio=PIO4 wdma=WDMA2 udma=UDMA133 cable=80 wire
ad2: 76351MB <SAMSUNG SP0802N TK100-23> at ata1-master PIO4
ad2: 156368016 sectors [155127C/16H/63S] 16 sectors/interrupt 1 depth queue
ad2: VIA check1 failed
ad2: Adaptec check1 failed
ad2: LSI (v3) check1 failed
ad2: LSI (v2) check1 failed
ad2: FreeBSD check1 failed
acd0: <HL-DT-ST DVDRAM GSA-4160B/A304> DVDR drive at ata1 as slave
acd0: read 6890KB/s (6890KB/s) write 6890KB/s (6890KB/s), 2048KB buffer, PIO4
acd0: Reads: CDR, CDRW, CDDA stream, DVDROM, DVDR, DVDRAM, packet
acd0: Writes: CDR, CDRW, DVDR, DVDRAM, test write, burnproof
acd0: Audio: play, 256 volume levels
acd0: Mechanism: ejectable tray, unlocked
acd0: Medium: no/blank disc
GEOM: new disk ad0
GEOM: new disk ad1
GEOM: new disk ad2
acd0: FAILURE - INQUIRY ILLEGAL REQUEST asc=0x24 ascq=0x00 sks=0x40 0x00 0x01
(probe0:ata1:0:1:0): error 22
(probe0:ata1:0:1:0): Unretryable Error
(probe0:ata1:0:1:0): error 6
(probe0:ata1:0:1:0): Unretryable Error
acd0: FAILURE - INQUIRY ILLEGAL REQUEST asc=0x24 ascq=0x00 sks=0x40 0x00 0x01
(probe0:ata1:0:1:0): error 22
(probe0:ata1:0:1:0): Unretryable Error
pass0 at ata1 bus 0 target 1 lun 0
pass0: <HL-DT-ST DVDRAM GSA-4160B A304> Removable CD-ROM SCSI-0 device
pass0: 16.000MB/s transfers
GEOM: new disk cd0
ATA PseudoRAID loaded
SMP: AP CPU #1 Launched!
cpu1 AP:
ID: 0x01000000 VER: 0x00050014 LDR: 0x00000000 DFR: 0xffffffff
lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
timer: 0x000200ef therm: 0x00010000 err: 0x00010000 pcm: 0x00010000
ioapic0: Assigning ISA IRQ 1 to local APIC 0
ioapic0: Assigning ISA IRQ 4 to local APIC 1
ioapic0: Assigning ISA IRQ 6 to local APIC 0
ioapic0: Assigning ISA IRQ 9 to local APIC 1
ioapic0: Assigning ISA IRQ 14 to local APIC 0
ioapic0: Assigning ISA IRQ 15 to local APIC 1
ioapic0: Assigning PCI IRQ 19 to local APIC 0
ioapic0: Assigning PCI IRQ 20 to local APIC 1
ioapic0: Assigning PCI IRQ 21 to local APIC 0
ioapic0: Assigning PCI IRQ 22 to local APIC 1
ioapic0: Assigning PCI IRQ 23 to local APIC 0
ioapic1: Assigning PCI IRQ 24 to local APIC 1
(cd0:ata1:0:1:0): error 6
(cd0:ata1:0:1:0): Unretryable Error
cd0 at ata1 bus 0 target 1 lun 0
cd0: <HL-DT-ST DVDRAM GSA-4160B A304> Removable CD-ROM SCSI-0 device
cd0: 16.000MB/s transfers
cd0: Attempt to query device size failed: NOT READY, Medium not present
(cd0:ata1:0:1:0): error 6
(cd0:ata1:0:1:0): Unretryable Error
(cd0:ata1:0:1:0): error 6
(cd0:ata1:0:1:0): Unretryable Error
(cd0:ata1:0:1:0): error 6
(cd0:ata1:0:1:0): Unretryable Error
Trying to mount root from ufs:/dev/ad0s4a
start_init: trying /sbin/init
Loading configuration files.
Entropy harvesting:
interrupts
ethernet
point_to_point
kickstart
.
swapon: adding /dev/ad1s2b as swap device
Starting file system checks:
/dev/ad0s4a: FILE SYSTEM CLEAN; SKIPPING CHECKS
/dev/ad0s4a: clean, 5101212 free (6140 frags, 636884 blocks, 0.1% fragmentation)
/dev/ad0s4d: FILE SYSTEM CLEAN; SKIPPING CHECKS
/dev/ad1s2e: FILE SYSTEM CLEAN; SKIPPING CHECKS
/dev/ad1s2e: clean, 9475107 free (227355 frags, 1155969 blocks, 1.0%
fragmentation)
/dev/ad2s4e: FILE SYSTEM CLEAN; SKIPPING CHECKS
/dev/ad2s4e: clean, 5064171 free (355 frags, 632977 blocks, 0.0% fragmentation)
/dev/ad0s4d: clean, 540528 free (208 frags, 67540 blocks, 0.0% fragmentation)
/dev/ad1s2d: FILE SYSTEM CLEAN; SKIPPING CHECKS
/dev/ad1s2d: clean, 1757665 free (6793 frags, 218859 blocks, 0.3% fragmentation)
/dev/ad0s1: FILESYSTEM CLEAN; SKIPPING CHECKS
/dev/ad2s4d: FILE SYSTEM CLEAN; SKIPPING CHECKS
/dev/ad2s4d: clean, 991388 free (60 frags, 123916 blocks, 0.0% fragmentation)
/dev/ad2s1: FILESYSTEM CLEAN; SKIPPING CHECKS
/dev/ad2s2: FILESYSTEM CLEAN; SKIPPING CHECKS
/dev/ad1s1: FILESYSTEM CLEAN; SKIPPING CHECKS
/dev/ad0s2: FILESYSTEM CLEAN; SKIPPING CHECKS
/dev/ad1s4: FILESYSTEM CLEAN; SKIPPING CHECKS
/dev/ad0s3: FILESYSTEM CLEAN; SKIPPING CHECKS
/dev/ad1s3: FILESYSTEM CLEAN; SKIPPING CHECKS
Mounting local file systems:
.
Setting hostname: lobo.
net.inet.tcp.blackhole:
0
->
1
net.inet.udp.blackhole:
0
->
1
net.inet.udp.maxdgram:
9216
->
63535
kern.maxfiles:
12328
->
65536
kern.ipc.somaxconn:
128
->
4096
kern.ipc.shmmax:
33554432
->
50331648
kern.ipc.shmall:
8192
->
16384
hw.snd.pcm0.vchans:
1
->
4
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
inet 127.0.0.1 netmask 0xff000000
re0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
options=5b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,POLLING>
inet 10.10.10.2 netmask 0xffffff00 broadcast 10.10.10.255
ether 00:1a:92:91:29:d4
media: Ethernet autoselect (none)
status: no carrier
add net default: gateway 10.10.10.1
Additional routing options:
.
Starting devd.
Starting ums0 moused:
.
hw.acpi.cpu.cx_lowest:
C1
sysctl:
hw.acpi.cpu.cx_lowest
:
Invalid argument
Mounting NFS file systems:
.
Mounting SMB file systems:
netsmb_dev: loaded
.
ELF ldconfig path: /lib /usr/lib /usr/lib/compat /usr/X11R6/lib /usr/local/lib
/usr/local/lib/compat/pkg /usr/X11R6/lib /usr/X11R6/lib/evolution/2.6
/usr/local/lib /usr/local/lib/ardour2 /usr/local/lib/ardour2/surfaces
/usr/local/lib/compat /usr/local/lib/compat/pkg /usr/local/lib/graphviz
/usr/local/lib/kde3 /usr/local/lib/mplayer/vidix /usr/local/lib/mysql
/usr/local/lib/nss /usr/local/lib/pth /usr/local/lib/wine /usr/X11R6/lib
/usr/X11R6/lib/evolution/2.6 /usr/local/lib /usr/local/lib/ardour2
/usr/local/lib/ardour2/surfaces /usr/local/lib/compat /usr/local/lib/compat/pkg
/usr/local/lib/graphviz /usr/local/lib/kde3 /usr/local/lib/mplayer/vidix
/usr/local/lib/mysql /usr/local/lib/nss /usr/local/lib/pth /usr/local/lib/wine
a.out ldconfig path: /usr/lib/aout /usr/lib/compat/aout /etc/ld.so.conf
Clearing /tmp.
Creating and/or trimming log files:
.
Starting syslogd.
Initial i386 initialization:
.
Additional ABI support:
linux
.
Starting local daemons:
.
Updating motd
.
Mounting late file systems:
.
Starting usbd.
Starting cupsd.
Removing stale Samba tdb files:
done
Configuring syscons:
keymap
font8x16
font8x14
font8x8
blanktime
allscreens
.
Starting cron.
Local package initialization:
rtc
.
Additional TCP options:
.
Starting background file system checks in 60 seconds.
Thu Aug 9 19:50:47 BRT 2007
Aug 9 20:25:08 lobo login: ROOT LOGIN (root) ON ttyv0
_______________________________________________
freebsd-hackers@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-hackers
To unsubscribe, send any mail to "[EMAIL PROTECTED]"
