Hi again,
I installed fbsd 49 on other disk/ide ctrl (ad0),
and boot verbose :
...
BIOS Geometries:
0:03fefe3f 0..1022=1023 cylinders, 0..254=255 heads, 1..63=63 sectors
0:03fffe3f 0..1022=1024 cylinders, 0..254=255 heads, 1..63=63 sectors
0 accounted for
Device configuration finished.
...
ad0: success setting UDMA5 on intel chip
Creating DISK ad0
ar: FreeBSD check1 failed
ad0: <Maxtor 6E040L0/NAR61590> ATA-7 disk at ata0-master
ad0: 39205MB (80293248 sectors), 79656 C, 16 H, 63 S, 512 B
ad0: 16 secs/int, 1 depth queue, UDMA100
ad0: piomode=4 dmamode=2 udmamode=6 cblid=1
ad4: success setting UDMA5 on Promise chip
Creating DISK ad4
ad4: READ command timeout tag=0 serv=0 - resetting
ata2: resetting devices .. ata2: mask=03 ostat0=58 ostat2=08
ad4: ATAPI 00 00
ata2-slave: ATAPI 00 00
ata2: mask=03 stat0=50 stat1=00
ad4: ATA 01 a5
ata2-slave: ATA 01 a5
ata2: devices=03
ata2-slave: ATA identify retries exceeded
ad4: success setting UDMA5 on Promise chip
done
ar: Promise read conf failed
ad4: <WDC WD2500JB-32FUA0/15.05R15> ATA-6 disk at ata2-master
ad4: 238475MB (488397168 sectors), 484521 C, 16 H, 63 S, 512 B
ad4: 16 secs/int, 1 depth queue, UDMA100
ad4: piomode=4 dmamode=2 udmamode=5 cblid=1
ad4: READ command timeout tag=0 serv=0 - resetting
ata2: resetting devices .. ata2: mask=03 ostat0=58 ostat2=08
ad4: ATAPI 00 00
ata2-slave: ATAPI 00 00
ata2: mask=03 stat0=50 stat1=00
ad4: ATA 01 a5
ata2-slave: ATA 01 a5
ata2: devices=03
ata2-slave: ATA identify retries exceeded
ad4: success setting UDMA5 on Promise chip
done
ad4: READ command timeout tag=0 serv=0 - resetting
ata2: resetting devices .. ata2: mask=03 ostat0=58 ostat2=08
ad4: ATAPI 00 00
ata2-slave: ATAPI 00 00
ata2: mask=03 stat0=50 stat1=00
ad4: ATA 01 a5
ata2-slave: ATA 01 a5
ata2: devices=03
ata2-slave: ATA identify retries exceeded
ad4: success setting UDMA5 on Promise chip
done
ad4: READ command timeout tag=0 serv=0 - resetting
ad4: success setting PIO4 on Promise chip
ad4: trying fallback to PIO mode
ata2: resetting devices .. ata2: mask=03 ostat0=50 ostat2=00
ad4: ATAPI 00 00
ata2-slave: ATAPI 00 00
ata2: mask=03 stat0=50 stat1=00
ad4: ATA 01 a5
ata2: devices=01
ad4: success setting PIO4 on Promise chip
done
Fatal trap 12: page fault while in kernel mode
fault virtual address = 0x78007a
fault code = supervisor read, page not present
instruction pointer = 0x8:0xc02577be
stack pointer = 0x10:0xc042a27c
frame pointer = 0x10:0xc042a284
code segment = base 0x0, limit 0xfffff, type 0x1b
= DPL 0, pres 1, def32 1, gran 1
processor eflags = interrupt enabled, resume, IOPL = 0
current process = idle
interrupt mask = bio
trap number = 12
panic: page fault
I repeat, same hardware (promise Fasttrack100) [same two ide cable)
with two ide disk Maxtor 40Go-ata133 is GOOD ! (fbsd49 installed
and kernel recompiled whitout pb)
Regard
On Fri, 30 Jan 2004, rmkml wrote:
> Date: Fri, 30 Jan 2004 23:32:23 +0100 (CET)
> From: rmkml <[EMAIL PROTECTED]>
> To: [EMAIL PROTECTED]
> Subject: Promise raid ATA Timeout (fbsd49) with 250Go !
>
> Hi,
>
> I have Timeout during boot
>
> before panic !
>
> I used fbsd v4.9release, (2x250Go WD ATA100)
>
> but if use v5.2R : OK no pb !
>
> If I use 40Go on same Hardware : OK with 49
>
> Possible Help me ?
>
> Where is download last 4.9 boot floppy ?
>
> Possible to increase the duration of initialization at the time of the
> boot ?
>
> Regards
>
> [EMAIL PROTECTED]
>
> _______________________________________________
> [EMAIL PROTECTED] mailing list
> http://lists.freebsd.org/mailman/listinfo/freebsd-hackers
> To unsubscribe, send any mail to "[EMAIL PROTECTED]"
>
_______________________________________________
[EMAIL PROTECTED] mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-hackers
To unsubscribe, send any mail to "[EMAIL PROTECTED]"
