Hi
I have a problem getting CURRENT to find my ISA SMC Ultra ethernet
card. No matter what I do I can't stop the kernel finding a third
sio device on top of the memory and interrupt that the ed card
occupies. The kernel correctly registers its surprise at finding
the third sio device since no hints for it exist:
sio0 port 0x3f8-0x3ff irq 4 on acpi0
sio0: type 16550A
sio1 port 0x2f8-0x2ff irq 3 on acpi0
sio1: type 16550A
sio2: configured irq 10 not in bitmap of probed irqs 0
sio2: port may not be enabled
sio2 port 0x2e8-0x2ef irq 10 on acpi0
sio2: type 16550A
I've tried setting hint.sio.2.disabled=1. I've tried leaving it
out. I can't not have sio because this server is my router and is
permanently connected to a modem.
The SMC Ultra card exists on 0x280 irq 10 0xd8000. Has current
dropped ISA support (which was hinted at in the GENERIC/80386
thread)?
Any ideas?
Kernel config, device.hints, dmesg.boot follows.
Ian
Copyright (c) 1992-2002 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.0-CURRENT #2: Tue Dec 17 14:17:13 SAST 2002
[EMAIL PROTECTED]:/usr/src/sys/i386/compile/BRANE-DEAD
Preloaded elf kernel "/boot/kernel/kernel" at 0xc0455000.
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium II/Pentium II Xeon/Celeron (267.27-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x634 Stepping = 4
Features=0x80fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,MMX>
real memory = 201261056 (191 MB)
avail memory = 190504960 (181 MB)
Programming 24 pins in IOAPIC #0
IOAPIC #0 intpin 2 -> irq 0
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
cpu0 (BSP): apic id: 0, version: 0x00040011, at 0xfee00000
cpu1 (AP): apic id: 1, version: 0x00040011, at 0xfee00000
io0 (APIC): apic id: 2, version: 0x00170011, at 0xfec00000
Initializing GEOMetry subsystem
Pentium Pro MTRR support enabled
acpi0: <GBT AWRDACPI> on motherboard
ACPI-0625: *** Info: GPE Block0 defined as GPE0 to GPE15
Using $PIR table, 8 entries at 0xc00fdc60
acpi0: power button is handled as a fixed feature programming model.
Timecounter "ACPI-safe" frequency 3579545 Hz
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x4008-0x400b on acpi0
acpi_cpu0: <CPU> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0x5000-0x500f,0x4000-0x4041,0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
IOAPIC #0 intpin 16 -> irq 2
agp0: <Intel 82443LX (440 LX) host to PCI bridge> mem 0xe0000000-0xe3ffffff at device
0.0 on pci0
pcib1: <PCIBIOS PCI-PCI bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
pci1: <display, VGA> at device 0.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 ATA33 controller> port 0xf000-0xf00f at device 7.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0xe000-0xe01f irq 12 at device
7.2 on pci0
usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
Timecounter "PIIX" frequency 3579545 Hz
pci0: <bridge, PCI-unknown> at device 7.3 (no driver attached)
xl0: <3Com 3c905-TX Fast Etherlink XL> port 0xe400-0xe43f irq 2 at device 8.0 on pci0
xl0: Ethernet address: 00:60:08:0b:2e:c8
miibus0: <MII bus> on xl0
nsphy0: <DP83840 10/100 media interface> on miibus0
nsphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
ahc0: <Adaptec aic7880 Ultra SCSI adapter> port 0xe800-0xe8ff mem
0xe9000000-0xe9000fff irq 2 at device 12.0 on pci0
ahc0: Using left over BIOS settings
aic7880: Ultra Single Channel A, SCSI Id=7, 16/253 SCBs
fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> port 0x3f7,0x3f2-0x3f5
irq 6 drq 2 on acpi0
sio0 port 0x3f8-0x3ff irq 4 on acpi0
sio0: type 16550A
sio1 port 0x2f8-0x2ff irq 3 on acpi0
sio1: type 16550A
sio2: configured irq 10 not in bitmap of probed irqs 0
sio2: port may not be enabled
sio2 port 0x2e8-0x2ef irq 10 on acpi0
sio2: type 16550A
ppc0 port 0x778-0x77b,0x378-0x37f irq 7 drq 3 on acpi0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/16 bytes threshold
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
npx0: <math processor> on motherboard
npx0: INT 16 interface
orm0: <Option ROMs> at iomem 0xc8000-0xc87ff,0xc0000-0xc7fff on isa0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
APIC_IO: Testing 8254 interrupt delivery
APIC_IO: routing 8254 via IOAPIC #0 intpin 2
Timecounters tick every 10.000 msec
acpi_cpu: CPU throttling enabled, 8 steps from 100% to 12.5%
ad0: 4103MB <ST34342A> [8894/15/63] at ata0-master UDMA33
Waiting 15 seconds for SCSI devices to settle
SMP: AP CPU #1 Launched!
Mounting root from ufs:/dev/ad0s1a
cd0 at ahc0 bus 0 target 4 lun 0
cd0: <YAMAHA CRW4260 1.0q> Removable CD-ROM SCSI-2 device
cd0: 3.300MB/s transfers
cd0: Attempt to query device size failed: NOT READY, Medium not present - tray closed
cd1 at ahc0 bus 0 target 6 lun 0
cd1: <PIONEER CD-ROM DR-U12X 1.06> Removable CD-ROM SCSI-2 device
cd1: 10.000MB/s transfers (10.000MHz, offset 15)
cd1: Attempt to query device size failed: NOT READY, Medium not present
ipfw2 initialized, divert disabled, rule-based forwarding enabled, default to deny,
logging disabled
hint.fdc.0.at="isa"
hint.fdc.0.port="0x3F0"
hint.fdc.0.irq="6"
hint.fdc.0.drq="2"
hint.fd.0.at="fdc0"
hint.fd.0.drive="0"
hint.ata.0.at="isa"
hint.ata.0.port="0x1F0"
hint.ata.0.irq="14"
hint.ata.1.at="isa"
hint.ata.1.port="0x170"
hint.ata.1.irq="15"
hint.atkbdc.0.at="isa"
hint.atkbdc.0.port="0x060"
hint.atkbd.0.at="atkbdc"
hint.atkbd.0.irq="1"
hint.atkbd.0.flags="0x1"
hint.vga.0.at="isa"
hint.sc.0.at="isa"
hint.sc.0.flags="0x100"
hint.sio.0.at="isa"
hint.sio.0.port="0x3F8"
hint.sio.0.flags="0x10"
hint.sio.0.irq="4"
hint.sio.1.at="isa"
hint.sio.1.port="0x2F8"
hint.sio.1.irq="3"
hint.ppc.0.at="isa"
hint.ppc.0.irq="7"
hint.ed.0.at="isa"
hint.ed.0.port="0x280"
hint.ed.0.irq="10"
hint.ed.0.maddr="0xd8000"
machine i386
cpu I686_CPU
ident "BRANE-DEAD"
maxusers 256
#To statically compile in device wiring instead of /boot/device.hints
hints "BRANE-DEAD.hints" #Default places to look for devices.
options INET #InterNETworking
options FFS #Berkeley Fast Filesystem
options SOFTUPDATES #Enable FFS soft updates support
options UFS_ACL #Support for access control lists
options UFS_DIRHASH #Improve performance on big directories
options COMPAT_43 #Compatible with BSD 4.3 [KEEP THIS!]
options COMPAT_FREEBSD4 #Compatible with FreeBSD4
options SCSI_DELAY=15000 #Delay (in ms) before probing SCSI
options KTRACE #ktrace(1) support
options SYSVSHM #SYSV-style shared memory
options SYSVMSG #SYSV-style message queues
options SYSVSEM #SYSV-style semaphores
options _KPOSIX_PRIORITY_SCHEDULING #Posix P1003_1B real-time extensions
options KBD_INSTALL_CDEV # install a CDEV entry in /dev
options AHC_REG_PRETTY_PRINT # Print register bitfields in debug
options IPDIVERT
# output. Adds ~128k to driver.
# To make an SMP kernel, the next two are needed
options SMP # Symmetric MultiProcessor Kernel
options APIC_IO # Symmetric (APIC) I/O
device isa
device pci
device acpi
#options ACPI_DEBUG
# Floppy drives
device fdc
# ATA and ATAPI devices
device ata
device atadisk # ATA disk drives
options ATA_STATIC_ID #Static device numbering
# SCSI Controllers
device ahc # AHA2940 and onboard AIC7xxx devices
# SCSI peripherals
device scbus # SCSI bus (required)
device da # Direct Access (disks)
device sa # Sequential Access (tape etc)
device cd # CD
device pass # Passthrough device (direct SCSI access)
device ses # SCSI Environmental Services (and SAF-TE)
# atkbdc0 controls both the keyboard and the PS/2 mouse
device atkbdc # AT keyboard controller
device atkbd # AT keyboard
device psm # PS/2 mouse
device vga # VGA video card driver
# syscons is the default console driver, resembling an SCO console
device sc
device agp # support several AGP chipsets
# Floating point support - do not disable.
device npx
# Serial (COM) ports
device sio # 8250, 16[45]50 based serial ports
# Parallel port
device ppc
device ppbus # Parallel port bus (required)
device lpt # Printer
device plip # TCP/IP over parallel
device ppi # Parallel port interface device
#device vpo # Requires scbus and da
# PCI Ethernet NICs that use the common MII bus controller code.
# NOTE: Be sure to keep the 'device miibus' line in order to use these NICs!
device miibus # MII bus support
device xl # 3Com 3c90x (``Boomerang'', ``Cyclone'')
device ed # NE[12]000, SMC Ultra, 3c503, DS8390 cards
# Pseudo devices - the number indicates how many units to allocate.
device random # Entropy device
device loop # Network loopback
device ether # Ethernet support
device sl # Kernel SLIP
device ppp # Kernel PPP
device tun # Packet tunnel.
device pty # Pseudo-ttys (telnet etc)
device md # Memory "disks"
# The `bpf' device enables the Berkeley Packet Filter.
# Be aware of the administrative consequences of enabling this!
device bpf # Berkeley packet filter
# USB support
device uhci # UHCI PCI->USB interface
device usb # USB Bus (required)
