>Submitter-Id: current-users
>Originator: Vladimir B. Grebenschikov
>Organization: SWsoft
>Confidential: no
>Synopsis: WaveLan driver problems with latest -CURRENT
>Severity: serious
>Priority: medium
>Category: kern
>Class: sw-bug
>Release: FreeBSD 5.0-CURRENT i386
>Environment:
System: FreeBSD vbook.express.ru 5.0-CURRENT FreeBSD 5.0-CURRENT #12: Wed Nov 27
16:18:57 MSK 2002 [EMAIL PROTECTED]:/usr/obj/usr/local/src/sys/VBOOK i386
>Description:
Hi
After upgrade from CURRENT dated September 8
to fresh -CURRENT my Orinoco Silver WaveLan card stop working:
System boots, detects card:
cbb0: <RF5C475 PCI-CardBus Bridge> at device 10.0 on pci0
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
pcib0: matched entry for 0.10.INTA (source \\_SB_.LNKB)
pcib0: slot 10 INTA is routed to irq 9
...
pccard0: CIS version PC Card Standard 5.0
pccard0: CIS info: Lucent Technologies, WaveLAN/IEEE, Version 01.01,
pccard0: Manufacturer code 0x156, product 0x2
pccard0: function 0: network adapter, ccr addr 3e0 mask 1
pccard0: function 0, config table entry 1: I/O card; irq mask ffff;
iomask 6, iospace 0-3f; io16 irqpulse irqlevel
wi0: <WaveLAN/IEEE> at port 0x100-0x13f irq 9 function 0 config 1 on
pccard0
wi0: 802.11 address: 00:02:2d:09:56:e6
wi0: using Lucent Technologies, WaveLAN/IEEE
wi0: Lucent Firmware: Station 6.06.01
wi0: wi_has_wep = 1
wi0: bpf attached
But simple 'ifconfig wi0' causes following output on console:
wi0: timeout in wi_cmd 0x0021; event status 0x0000
wi0: timeout in wi_cmd 0x0021; event status 0x0000
wi0: timeout in wi_cmd 0x0021; event status 0x0000
wi0: timeout in wi_cmd 0x0021; event status 0x0000
wi0: timeout in wi_cmd 0x0021; event status 0x0000
wi0: timeout in wi_cmd 0x0021; event status 0x0000
just on first try it shows:
wi0: timeout in stray irq 7
got 5 stray irq 7's: not logging anymore
wi_cmd 0x0021; event status 0x0000
and ifconfig output:
wi0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
ether 00:02:2d:09:56:e6
media: IEEE 802.11 Wireless Ethernet autoselect
status: no carrier
(no wi-related parameters: channel, wep, etc ...)
Each timeout freeze system for about 1 sec.
Any Ideas, what happens ?
I am a bit confused that irq 9 assigned to wi, but stray irq 7
(stray irq 7 may be due to not loaded driver for ppc, but no
parallel devices was plugged)
May be it is ACPI (PnP) problem ?
dmesg.boot (-v) in attachment
part of 'sysctl hw':
hw.cardbus.debug: 0
hw.cardbus.cis_debug: 0
hw.pccard.debug: 0
hw.pccard.cis_debug: 0
hw.cbb.start_memory: 2281701376
hw.cbb.start_16_io: 256
hw.cbb.start_32_io: 4096
hw.cbb.debug: 0
hw.pci.enable_io_modes: 1
hw.pci.allow_unsupported_io_range: 0
My notebook is VAIO PCG-z505S
Any suggestions is very appreciated.
dmesg.boot:
===============================
Copyright (c) 1992-2002 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.0-CURRENT #8: Sat Nov 23 01:03:18 MSK 2002
[EMAIL PROTECTED]:/usr/obj/usr/local/src/sys/VBOOK
Preloaded elf kernel "/boot/kernel/kernel" at 0xc049b000.
Preloaded elf module "/boot/kernel/snd_pcm.ko" at 0xc049b0b4.
Preloaded elf module "/boot/kernel/snd_neomagic.ko" at 0xc049b160.
Preloaded elf module "/boot/kernel/ukbd.ko" at 0xc049b214.
Preloaded elf module "/boot/kernel/usb.ko" at 0xc049b2c0.
Preloaded elf module "/boot/kernel/ums.ko" at 0xc049b368.
Preloaded elf module "/boot/kernel/acpi.ko" at 0xc049b410.
Calibrating clock(s) ... TSC clock: 331561241 Hz, i8254 clock: 1193119 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz
CLK_USE_TSC_CALIBRATION not specified - using old calibration method
Timecounter "TSC" frequency 331581025 Hz
CPU: Pentium II/Pentium II Xeon/Celeron (331.58-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x66a Stepping = 10
Features=0x183f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR>
real memory = 201261056 (191 MB)
Physical memory chunk(s):
0x00001000 - 0x0009efff, 647168 bytes (158 pages)
0x004c2000 - 0x0bfe7fff, 196239360 bytes (47910 pages)
avail memory = 190623744 (181 MB)
bios32: Found BIOS32 Service Directory header at 0xc00f6c40
bios32: Entry = 0xfd7c0 (c00fd7c0) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0xfd7c0+0x214
pnpbios: Found PnP BIOS data at 0xc00f6c70
pnpbios: Entry = f0000:b5cb Rev = 1.0
Other BIOS signatures found:
Initializing GEOMetry subsystem
null: <null device, zero device>
mem: <memory & I/O>
Pentium Pro MTRR support enabled
random: <entropy source>
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <PTLTD RSDT > on motherboard
pci_open(1): mode 1 addr port (0x0cf8) is 0x80003b54
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=71928086)
Using $PIR table, 7 entries at 0xc00fdf50
PCI-Only Interrupts: none
Location Bus Device Pin Link IRQs
embedded 0 1 A 0x60 9
embedded 0 1 B 0x61 9
embedded 0 1 C 0x62 9
embedded 0 1 D 0x63 9
embedded 0 7 D 0x63 9
embedded 0 8 A 0x60 9
embedded 0 8 B 0x61 9
embedded 0 9 A 0x62 9
embedded 0 10 A 0x61 9
embedded 0 11 A 0x60 9
embedded 0 6 A 0x60 9
acpi0: power button is handled as a fixed feature programming model.
ACPI timer looks BAD min = 1, max = 16777215, width = 16777215
ACPI timer looks BAD min = 2, max = 8, width = 7
ACPI timer looks BAD min = 2, max = 8, width = 7
ACPI timer looks BAD min = 2, max = 16777213, width = 16777212
ACPI timer looks BAD min = 2, max = 12, width = 11
ACPI timer looks BAD min = 1, max = 7, width = 7
ACPI timer looks BAD min = 1, max = 8, width = 8
ACPI timer looks BAD min = 1, max = 16777215, width = 16777215
ACPI timer looks BAD min = 1, max = 8, width = 8
ACPI timer looks BAD min = 2, max = 8, width = 7
Timecounter "ACPI-safe" frequency 3579545 Hz
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x8008-0x800b on acpi0
acpi_cpu0: <CPU> on acpi0
acpi_tz0: <thermal zone> on acpi0
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
---- initial configuration ------------------------
\\_SB_.LNKD irq 9: [ 9] low,level,sharable 0.7.3
\\_SB_.LNKA irq 9: [ 9] low,level,sharable 0.8.0
\\_SB_.LNKC irq 9: [ 9] low,level,sharable 0.9.0
\\_SB_.LNKB irq 9: [ 9] low,level,sharable 0.10.0
\\_SB_.LNKA irq 9: [ 9] low,level,sharable 0.11.0
\\_SB_.LNKB irq 9: [ 9] low,level,sharable 0.8.1
\\_SB_.LNKA irq 9: [ 9] low,level,sharable 0.6.0
---- before setting priority for links ------------
---- before fixup boot-disabled links -------------
---- after fixup boot-disabled links --------------
---- arbitrated configuration ---------------------
\\_SB_.LNKD irq 9: [ 9] low,level,sharable 0.7.3
\\_SB_.LNKA irq 9: [ 9] low,level,sharable 0.8.0
\\_SB_.LNKC irq 9: [ 9] low,level,sharable 0.9.0
\\_SB_.LNKB irq 9: [ 9] low,level,sharable 0.10.0
\\_SB_.LNKA irq 9: [ 9] low,level,sharable 0.11.0
\\_SB_.LNKB irq 9: [ 9] low,level,sharable 0.8.1
\\_SB_.LNKA irq 9: [ 9] low,level,sharable 0.6.0
pci0: <ACPI PCI bus> on pcib0
pci0: physical bus=0
map[10]: type 3, range 32, base 00000000, size 26, enabled
found-> vendor=0x8086, dev=0x7192, revid=0x03
bus=0, slot=0, func=0
class=06-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0106, statreg=0xa200, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[10]: type 1, range 32, base fedef000, size 12, enabled
map[14]: type 4, range 32, base 0000fcc0, size 6, enabled
map[18]: type 1, range 32, base fec00000, size 20, enabled
found-> vendor=0x8086, dev=0x1229, revid=0x08
bus=0, slot=6, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0013, statreg=0x0290, cachelnsz=8 (dwords)
lattimer=0x42 (1980 ns), mingnt=0x08 (2000 ns), maxlat=0x38 (14000 ns)
intpin=a, irq=9
powerspec 2 supports D0 D1 D2 D3 current D0
found-> vendor=0x8086, dev=0x7110, revid=0x02
bus=0, slot=7, func=0
class=06-80-00, hdrtype=0x00, mfdev=1
cmdreg=0x000f, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[20]: type 4, range 32, base 0000fc90, size 4, enabled
found-> vendor=0x8086, dev=0x7111, revid=0x01
bus=0, slot=7, func=1
class=01-01-80, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[20]: type 4, range 32, base 0000fca0, size 5, enabled
found-> vendor=0x8086, dev=0x7112, revid=0x01
bus=0, slot=7, func=2
class=0c-03-00, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=d, irq=9
map[90]: type 4, range 32, base 00002180, size 4, enabled
found-> vendor=0x8086, dev=0x7113, revid=0x02
bus=0, slot=7, func=3
class=06-80-00, hdrtype=0x00, mfdev=0
cmdreg=0x0003, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[10]: type 3, range 32, base fd000000, size 24, enabled
map[14]: type 1, range 32, base fe400000, size 22, enabled
map[18]: type 1, range 32, base feb00000, size 20, enabled
found-> vendor=0x10c8, dev=0x0005, revid=0x20
bus=0, slot=8, func=0
class=03-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0003, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x80 (3840 ns), mingnt=0x10 (4000 ns), maxlat=0xff (63750 ns)
intpin=a, irq=9
powerspec 1 supports D0 D1 D2 D3 current D0
map[10]: type 3, range 32, base fe000000, size 22, enabled
map[14]: type 1, range 32, base fea00000, size 20, enabled
found-> vendor=0x10c8, dev=0x8005, revid=0x20
bus=0, slot=8, func=1
class=04-01-00, hdrtype=0x00, mfdev=1
cmdreg=0x0002, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=b, irq=9
powerspec 1 supports D0 D3 current D0
map[10]: type 1, range 32, base fedeec00, size 9, enabled
found-> vendor=0x104d, dev=0x8009, revid=0x01
bus=0, slot=9, func=0
class=0c-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0002, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=9
powerspec 1 supports D0 D3 current D0
found-> vendor=0x1180, dev=0x0475, revid=0x00
bus=0, slot=10, func=0
class=06-07-00, hdrtype=0x02, mfdev=0
cmdreg=0x0000, statreg=0x0210, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=255
powerspec 1 supports D0 D1 D2 D3 current D0
map[10]: type 1, range 32, base fedf0000, size 16, enabled
map[14]: type 4, range 32, base 0000fc88, size 3, enabled
found-> vendor=0x127a, dev=0x2005, revid=0x01
bus=0, slot=11, func=0
class=07-80-00, hdrtype=0x00, mfdev=0
cmdreg=0x0003, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=9
powerspec 2 supports D0 D3 current D3
pci0: <network, ethernet> at device 6.0 (no driver attached)
PCI-ISA bridge with incorrect subclass 0x80
PCI-ISA bridge with incorrect subclass 0x80
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 ATA33 controller> port 0xfc90-0xfc9f at device 7.1 on pci0
ata0: iobase=0x01f0 altiobase=0x03f6 bmaddr=0xfc90
ata0: mask=03 ostat0=50 ostat2=00
ata0-master: ATAPI 00 00
ata0-slave: ATAPI 00 00
ata0: mask=03 stat0=50 stat1=00
ata0-master: ATA 01 a5
ata0: devices=01
ata0: at 0x1f0 irq 14 on atapci0
ata1: iobase=0x0170 altiobase=0x0376 bmaddr=0xfc98
ata1: mask=03 ostat0=50 ostat2=50
ata1-master: ATAPI 00 00
ata1-slave: ATAPI 00 00
ata1: mask=03 stat0=50 stat1=50
ata1-master: ATA 01 a5
ata1-slave: ATA 01 a5
ata1: devices=03
ata1: at 0x170 irq 15 on atapci0
uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0xfca0-0xfcbf irq 9 at device
7.2 on pci0
usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhub1: Texas Instruments UT-USB41 hub, class 9/0, rev 1.10/1.10, addr 2
uhub1: 4 ports with 4 removable, self powered
ums0: Microsoft Microsoft IntelliMouse\M-. Explorer, rev 1.10/1.14, addr 3, iclass 3/1
ums0: 5 buttons and Z dir.
ukbd0: Behavior Tech. Computer Keyboard with mouse port, rev 1.00/1.00, addr 4, iclass
3/1
kbd: new array size 4
kbd1 at ukbd0
kbd1: ukbd0, generic (0), config:0x0, flags:0x1d0000
ums1: Behavior Tech. Computer Keyboard with mouse port, rev 1.00/1.00, addr 4, iclass
3/1
ums1: 3 buttons
intpm0: <Intel 82371AB Power management controller> port 0x2180-0x218f irq 9 at device
7.3 on pci0
intpm0: I/O mapped 2180
intpm0: intr IRQ 9 enabled revision 0
smbus0: <System Management Bus> on intsmb0
smb0: <SMBus generic I/O> on smbus0
intpm0: PM I/O mapped 8000
pci0: <display, VGA> at device 8.0 (no driver attached)
pcm0: <NeoMagic 256AV> mem 0xfea00000-0xfeafffff,0xfe000000-0xfe3fffff irq 9 at device
8.1 on pci0
pcm0: buftop is 0x0027ec00
pcm0: buftop is changed to 0x0027ec00
pcm0: ac97 codec id 0x414b4d01 (Asahi Kasei AK4542)
pcm0: ac97 codec features headphone, 5 bit master volume, AKM 3D Audio
pcm0: rec buf 0xcb4c5c00
pcm0: play buf 0xcb4c1c00
pci0: <serial bus, FireWire> at device 9.0 (no driver attached)
cbb0: <RF5C475 PCI-CardBus Bridge> at device 10.0 on pci0
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
pcib0: matched entry for 0.10.INTA (source \\_SB_.LNKB)
pcib0: slot 10 INTA is routed to irq 9
pci0: <simple comms> at device 11.0 (no driver attached)
speaker0 port 0x61 on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0047
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x1d0000
psm0: unable to allocate IRQ
psmcpnp0 irq 12 on acpi0
psm0: current command byte:0047
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model GlidePoint, device ID 0-00, 2 buttons
psm0: config:00000000, flags:00000000, packet size:3
psm0: syncmask:c0, syncbits:00
sio0: irq maps: 0x1 0x11 0x1 0x1
sio0 port 0x3f8-0x3ff irq 4 on acpi0
sio0: type 16550A, console
sio1: irq maps: 0x1 0x401 0x1 0x1
sio1 port 0x140-0x147,0x3e8-0x3ef irq 10 drq 0 on acpi0
sio1: type 16550A
unknown: not probed (disabled)
unknown: not probed (disabled)
unknown: not probed (disabled)
acpi_cmbat0: <Control method Battery> on acpi0
acpi_acad0: <AC adapter> on acpi0
unknown: not probed (disabled)
unknown: not probed (disabled)
unknown: not probed (disabled)
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
atkbdc: atkbdc0 already exists; skipping it
sio: sio0 already exists; skipping it
sio: sio1 already exists; skipping it
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <Option ROMs> at iomem 0xdc000-0xdffff,0xc0000-0xcbfff on isa0
fdc0 failed to probe at port 0x3f0 irq 6 drq 2 on isa0
pcic0 failed to probe at port 0x3e0 iomem 0xd0000 irq 10 on isa0
pmtimer0 on isa0
ppc0 failed to probe at irq 7 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x100>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 07 80 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
EGA/VGA parameters to be used for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
vt0 failed to probe on isa0
isa_probe_children: probing PnP devices
BIOS Geometries:
0:03feef3f 0..1022=1023 cylinders, 0..239=240 heads, 1..63=63 sectors
0 accounted for
Device configuration finished.
procfs registered
Timecounters tick every 10.000 msec
ipfw2 initialized, divert enabled, rule-based forwarding enabled, default to deny,
logging unlimited
lo0: bpf attached
DUMMYNET initialized (011031)
acpi_cpu0: set speed to 100.0%
acpi_cpu: CPU throttling enabled, 8 steps from 100% to 12.5%
acpi_cmbat0: battery initialization start
acpi_cmbat0: battery initialization done, tried 1 times
acpi_acad0: acline initialization start
acpi_acad0: On Line
acpi_acad0: acline initialization done, tried 1 times
pccard0: CIS version PC Card Standard 5.0
pccard0: CIS info: Lucent Technologies, WaveLAN/IEEE, Version 01.01,
pccard0: Manufacturer code 0x156, product 0x2
pccard0: function 0: network adapter, ccr addr 3e0 mask 1
pccard0: function 0, config table entry 1: I/O card; irq mask ffff; iomask 6, iospace
0-3f; io16 irqpulse irqlevel
wi0: <WaveLAN/IEEE> at port 0x100-0x13f irq 9 function 0 config 1 on pccard0
wi0: 802.11 address: 00:02:2d:09:56:e6
wi0: using Lucent Technologies, WaveLAN/IEEE
wi0: Lucent Firmware: Station 6.06.01
wi0: wi_has_wep = 1
wi0: bpf attached
ata1-slave: timeout waiting for interrupt
ata1-slave: ATA identify failed
ad0: success setting UDMA2 on Intel chip
GEOM: new disk ad0
ar: FreeBSD check1 failed
ad0: <IC25N020ATDA04-0/DA3OA70A> ATA-5 disk at ata0-master
ad0: 19077MB (39070080 sectors), 38760 C, 16 H, 63 S, 512 B
ad0: 16 secs/int, 1 depth queue, UDMA33
ad0: piomode=4 dmamode=2 udmamode=5 cblid=1
ad1: success setting PIO1 on generic chip
MBR Slice 1 on ad0:
0000 00 01 01 00 0b ef bf 29 3f 00 00 00 61 d0 7f 00 |.......)?...a...|
[0] f:00 typ:11 s(CHS):0/1/1 e(CHS):41/239/191 s:63 l:8376417
GEOM: Add ad0s1, start 32256 length 4288725504 end 4288757759
MBR Slice 2 on ad0:
0000 80 c0 81 2a a5 8f ff ff e0 ff 7f 00 e0 ff 7f 00 |...*............|
[1] f:80 typ:165 s(CHS):42/192/129 e(CHS):255/143/255 s:8388576 l:8388576
GEOM: Add ad0s2, start 4294950912 length 4294950912 end 8589901823
MBR Slice 3 on ad0:
0000 00 ff ff ff a0 ef ff ff c0 ff ff 00 50 52 06 00 |............PR..|
[2] f:00 typ:160 s(CHS):255/255/255 e(CHS):255/239/255 s:16777152 l:414288
GEOM: Add ad0s3, start 8589901824 length 212115456 end 8802017279
MBR Slice 4 on ad0:
0000 00 ff ff ff a5 ef ff ff 80 75 06 01 00 b4 4d 01 |.........u....M.|
[3] f:00 typ:165 s(CHS):255/255/255 e(CHS):255/239/255 s:17200512 l:21869568
GEOM: Add ad0s4, start 8806662144 length 11197218816 end 20003880959
ar: FreeBSD check1 failed
ad1: <MEMORYSTICK 4M 8K/SONY1.00> ATA-0 disk at ata1-master
ad1: 3MB (7904 sectors), 247 C, 2 H, 16 S, 512 B
ad1: 1 secs/int, 1 depth queue, PIO1
ad1: piomode=1 dmamode=-1 udmamode=-1 cblid=0
GEOM: new disk ad1
GEOM: Configure ad0s2a, start 0 length 134217728 end 134217727
GEOM: Configure ad0s2b, start 134217728 length 268435456 end 402653183
GEOM: Configure ad0s2c, start 0 length 4294950912 end 4294950911
GEOM: Configure ad0s2e, start 402653184 length 2147483648 end 2550136831
GEOM: Configure ad0s2f, start 2550136832 length 1744814080 end 4294950911
GEOM: Configure ad0s4a, start 0 length 134217728 end 134217727
GEOM: Configure ad0s4c, start 0 length 11197218816 end 11197218815
GEOM: Configure ad0s4e, start 134217728 length 2147483648 end 2281701375
GEOM: Configure ad0s4f, start 2281701376 length 8915517440 end 11197218815
MBR Slice 1 on ad1:
0000 80 01 0c 00 01 01 10 f5 1b 00 00 00 a5 1e 00 00 |................|
[0] f:80 typ:1 s(CHS):0/1/12 e(CHS):245/1/16 s:27 l:7845
GEOM: Add ad1s1, start 13824 length 4016640 end 4030463
Mounting root from ufs:/dev/ad0s2a
start_init: trying /sbin/init
Linux ELF exec handler installed
linprocfs registered
fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0xfcc0-0xfcff mem
0xfec00000-0xfecfffff,0xfedef000-0xfedeffff irq 9 at device 6.0 on pci0
fxp0: using memory space register mapping
fxp0: Ethernet address 08:00:46:04:31:b3
fxp0: PCI IDs: 8086 1229 104d 8057 0008
fxp0: Dynamic Standby mode is disabled
fxp0: bpf attached
inphy0: <i82555 10/100 media interface> on miibus0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100basstray irq 7
eTX-FDX, auto
===================================
>How-To-Repeat:
Use same configuration
>Fix:
To Unsubscribe: send mail to [EMAIL PROTECTED]
with "unsubscribe freebsd-current" in the body of the message
