I have a Dell Latitude CPx with a Xircom RealPort
CardBus Ethernet 10/100+Modem 56 card. The card used
to work on an Aug 1, 2001 -CURRENT. I've cvsup'ed and
built the system yesterday (sep 15) and cannot make the card
work anymore. Any ideas what might be wrong? I am attaching
dmesg and kernel config (NEWCARD). I have the following
in sio.c:
static struct pci_ids pci_ids[] = {
{ 0x0103115d, "Xircom Cardbus modem", 0x10 },
{ 0x00000000, NULL, 0 }
};
Copyright (c) 1992-2001 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.0-CURRENT #4: Sat Sep 15 14:23:16 CDT 2001
[EMAIL PROTECTED]:/mnt_usr/local/src/current/src/sys/i386/compile/NEWCARD
Calibrating clock(s) ... TSC clock: 647201286 Hz, i8254 clock: 1193208 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz
CLK_USE_TSC_CALIBRATION not specified - using old calibration method
Timecounter "TSC" frequency 647190546 Hz
CPU: Pentium III/Pentium III Xeon/Celeron (647.19-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x683 Stepping = 3
Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory = 134135808 (130992K bytes)
Physical memory chunk(s):
0x00001000 - 0x0009efff, 647168 bytes (158 pages)
0x0042b000 - 0x07fe3fff, 129732608 bytes (31673 pages)
avail memory = 126259200 (123300K bytes)
bios32: Found BIOS32 Service Directory header at 0xc00ffe80
bios32: Entry = 0xffe90 (c00ffe90) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0xf0000+0xc0be
pnpbios: Found PnP BIOS data at 0xc00fe2d0
pnpbios: Entry = f0000:e2f4 Rev = 1.0
pnpbios: Event flag at 4b4
Other BIOS signatures found:
Preloaded elf kernel "/boot/kernel/kernel" at 0xc0404000.
Preloaded elf module "/boot/kernel/snd_maestro3.ko" at 0xc04040b4.
Preloaded elf module "/boot/kernel/snd_pcm.ko" at 0xc0404168.
null: <null device, zero device>
random: <entropy source>
mem: <memory & I/O>
Pentium Pro MTRR support enabled
Math emulator present
pci_open(1): mode 1 addr port (0x0cf8) is 0x80003ac0
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=71908086)
Using $PIR table, 6 entries at 0xc00fbd30
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Intel 82443BX (440 BX) host to PCI bridge> at pcibus 0 on motherboard
pci0: physical bus=0
map[10]: type 3, range 32, base f4000000, size 26, enabled
found-> vendor=0x8086, dev=0x7190, revid=0x03
bus=0, slot=0, func=0
class=06-00-00, hdrtype=0x00, mfdev=0
found-> vendor=0x8086, dev=0x7191, revid=0x03
bus=0, slot=1, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
found-> vendor=0x104c, dev=0xac1c, revid=0x01
bus=0, slot=3, func=0
class=06-07-00, hdrtype=0x02, mfdev=1
intpin=a, irq=11
powerspec 1 supports D0 D1 D2 D3 current D0
found-> vendor=0x104c, dev=0xac1c, revid=0x01
bus=0, slot=3, func=1
class=06-07-00, hdrtype=0x02, mfdev=1
intpin=a, irq=11
powerspec 1 supports D0 D1 D2 D3 current D0
found-> vendor=0x8086, dev=0x7110, revid=0x02
bus=0, slot=7, func=0
class=06-80-00, hdrtype=0x00, mfdev=1
map[20]: type 4, range 32, base 00000860, size 4, enabled
found-> vendor=0x8086, dev=0x7111, revid=0x01
bus=0, slot=7, func=1
class=01-01-80, hdrtype=0x00, mfdev=0
map[20]: type 4, range 32, base 0000dce0, size 5, enabled
found-> vendor=0x8086, dev=0x7112, revid=0x01
bus=0, slot=7, func=2
class=0c-03-00, hdrtype=0x00, mfdev=0
intpin=d, irq=11
map[90]: type 4, range 32, base 00000840, size 4, enabled
found-> vendor=0x8086, dev=0x7113, revid=0x02
bus=0, slot=7, func=3
class=06-80-00, hdrtype=0x00, mfdev=0
map[10]: type 4, range 32, base 0000d800, size 8, enabled
map[14]: type 1, range 32, base faffe000, size 13, enabled
found-> vendor=0x125d, dev=0x1998, revid=0x10
bus=0, slot=8, func=0
class=04-01-00, hdrtype=0x00, mfdev=0
intpin=a, irq=5
powerspec 2 supports D0 D1 D2 D3 current D0
pci0: <PCI bus> on pcib0
pcib1: <PCI-PCI bridge> at device 1.0 on pci0
pcib1: secondary bus 1
pcib1: subordinate bus 1
pcib1: I/O decode 0xe000-0xefff
pcib1: memory decode 0xfc000000-0xfeffffff
pcib1: prefetched decode 0xfff00000-0xfffff
pci1: physical bus=1
map[10]: type 1, range 32, base fd000000, size 24, enabled
map[14]: type 4, range 32, base 0000ec00, size 8, enabled
map[18]: type 1, range 32, base fcfff000, size 12, enabled
found-> vendor=0x1002, dev=0x4c4d, revid=0x64
bus=1, slot=0, func=0
class=03-00-00, hdrtype=0x00, mfdev=0
intpin=a, irq=11
powerspec 1 supports D0 D1 D2 D3 current D0
pci1: <PCI bus> on pcib1
pci1: <display, VGA> at device 0.0 (no driver attached)
pccbb0: <TI1225 PCI-CardBus Bridge> irq 11 at device 3.0 on pci0
pccbb0: PCI Memory allocated: 10000000
cardbus0: <Cardbus bus (newcard)> on pccbb0
pccbb0: WARNING: cannot attach pccard bus.
pccbb1: <TI1225 PCI-CardBus Bridge> irq 11 at device 3.1 on pci0
pccbb1: PCI Memory allocated: 10001000
cardbus1: <Cardbus bus (newcard)> on pccbb1
pccbb1: WARNING: cannot attach pccard bus.
PCI-ISA bridge with incorrect subclass 0x80
PCI-ISA bridge with incorrect subclass 0x80
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 ATA33 controller> port 0x860-0x86f at device 7.1 on pci0
ata0: iobase=0x01f0 altiobase=0x03f6 bmaddr=0x0860
ata0: mask=03 ostat0=50 ostat2=00
ata0-slave: ATAPI probe 00 00
ata0-master: ATAPI probe 00 00
ata0: mask=03 stat0=50 stat1=00
ata0-master: ATA probe 01 a5
ata0: devices=01
ata0: at 0x1f0 irq 14 on atapci0
ata1: iobase=0x0170 altiobase=0x0376 bmaddr=0x0868
ata1: at 0x170 irq 15 on atapci0
pci0: <serial bus, USB> at device 7.2 (no driver attached)
pci0: <bridge, PCI-unknown> at device 7.3 (no driver attached)
pcm0: <ESS Technology Maestro3> port 0xd800-0xd8ff mem 0xfaffe000-0xfaffffff irq 5 at
device 8.0 on pci0
pcm0: ac97 codec id 0x83847609 (SigmaTel STAC9721/9723)
pcm0: ac97 codec features 18 bit DAC, 18 bit ADC, 5 bit master volume, SigmaTel 3D
Enhancement
pcm0: ac97 primary codec extended features AMAP
pcm: setmap 489000, 1000; 0xc2235000 -> 489000
pcm: setmap 44c000, 1000; 0xc2238000 -> 44c000
pnpbios: 16 devices, largest 276 bytes
PNP0a03: adding io range 0xcf8-0xcff, size=0x8, align=0x2
pnpbios: handle 0 device ID PNP0a03 (030ad041)
PNP0c01: adding fixed memory32 range 0-0x9ffff, size=0xa0000
PNP0c01: adding fixed memory32 range 0x100000-0x7ffffff, size=0x7f00000
PNP0c01: adding fixed memory32 range 0xf0000-0xfffff, size=0x10000
PNP0c01: adding fixed memory32 range 0xfffe0000-0xffffffff, size=0x20000
PNP0c01: adding fixed memory32 range 0x100a0000-0x100fffff, size=0x60000
PNP0c01: adding io range 0x800-0x83f, size=0x40, align=0x1
PNP0c01: adding io range 0x840-0x84f, size=0x10, align=0x1
PNP0c01: adding io range 0x600-0x67f, size=0x80, align=0x1
PNP0c01: adding io range 0x680-0x6ff, size=0x80, align=0x1
PNP0c01: adding io range 0x880-0x88f, size=0x10, align=0x1
PNP0c01: adding io range 0x3f0-0x3f1, size=0x2, align=0x1
PNP0c01: adding io range 0xe0-0xe1, size=0x2, align=0x1
pnpbios: handle 1 device ID PNP0c01 (010cd041)
PNP0c01: adding fixed memory32 range 0xed000000-0xedffffff, size=0x1000000
PNP0c01: adding io range 0xf400-0xf4fe, size=0xff, align=0x1
pnpbios: handle 2 device ID PNP0c01 (010cd041)
PNP0000: adding irq mask 0x4
PNP0000: adding io range 0x20-0x3f, size=0x20, align=0x1
PNP0000: adding io range 0xa0-0xbf, size=0x20, align=0x1
PNP0000: adding io range 0x4d0-0x4d1, size=0x2, align=0x1
pnpbios: handle 3 device ID PNP0000 (0000d041)
PNP0100: adding irq mask 0x1
PNP0100: adding io range 0x40-0x5f, size=0x20, align=0x1
pnpbios: handle 4 device ID PNP0100 (0001d041)
PNP0200: adding io range 0x80-0x9f, size=0x20, align=0x1
PNP0200: adding io range 0-0x1f, size=0x20, align=0x1
PNP0200: adding io range 0xc0-0xdf, size=0x20, align=0x1
PNP0200: adding dma mask 0x10
pnpbios: handle 5 device ID PNP0200 (0002d041)
PNP0303: adding irq mask 0x2
PNP0303: adding io range 0x60-0x60, size=0x1, align=0x1
PNP0303: adding io range 0x64-0x64, size=0x1, align=0x1
pnpbios: handle 6 device ID PNP0303 (0303d041)
PNP0f13: adding irq mask 0x1000
pnpbios: handle 7 device ID PNP0f13 (130fd041)
PNP0800: adding io range 0x61-0x61, size=0x1, align=0x1
pnpbios: handle 8 device ID PNP0800 (0008d041)
PNP0b00: adding irq mask 0x100
PNP0b00: adding io range 0x70-0x7f, size=0x10, align=0x1
pnpbios: handle 9 device ID PNP0b00 (000bd041)
PNP0c04: adding irq mask 0x2000
PNP0c04: adding io range 0xf0-0xff, size=0x10, align=0x1
pnpbios: handle 10 device ID PNP0c04 (040cd041)
PNP0e03: adding irq mask 0x20
PNP0e03: adding io range 0x3e0-0x3e1, size=0x2, align=0x1
pnpbios: handle 11 device ID PNP0e03 (030ed041)
PNP0501: adding irq mask 0x10
PNP0501: adding io range 0x3f8-0x3ff, size=0x8, align=0x8
pnpbios: handle 12 device ID PNP0501 (0105d041)
SMCf010: adding irq mask 0x10
SMCf010: adding io range 0x3f8-0x3ff, size=0x8, align=0x8
SMCf010: adding io range 0x270-0x277, size=0x8, align=0x8
pnpbios: handle 13 device ID SMCf010 (10f0a34d)
PNP0401: adding dma mask 0x8
PNP0401: adding irq mask 0x80
PNP0401: adding io range 0x378-0x37f, size=0x8, align=0x8
PNP0401: adding io range 0x778-0x77b, size=0x4, align=0x8
pnpbios: handle 14 device ID PNP0401 (0104d041)
PNP0700: adding irq mask 0x40
PNP0700: adding io range 0x3f2-0x3f5, size=0x4, align=0x2
PNP0700: adding io range 0x3f7-0x3f7, size=0x1, align=0x8
PNP0700: adding dma mask 0x4
pnpbios: handle 15 device ID PNP0700 (0007d041)
ata-: ata0 already exists, using ata2 instead
ata-: ata1 already exists, using ata3 instead
pcm-: pcm0 already exists, using pcm1 instead
sc-: sc0 already exists, using sc1 instead
vga-: vga0 already exists, using vga1 instead
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <Option ROM> at iomem 0xc0000-0xcffff on isa0
atkbd: the current kbd controller command byte 0065
atkbd: keyboard ID 0x41ab (2)
sc0: <System console> on isa0
sc0: VGA <16 virtual consoles, flags=0x200>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
vga0: vga: WARNING: video mode switching is not fully supported on this adapter
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 e7 73 4f 4f 97 52 83
b4 1f 00 4f 0d 0e 00 00 07 80 91 87 8f 28 1f 8f
b5 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
EGA/VGA parameters to be used for mode 24
50 18 10 00 00 00 03 00 02 e7 73 4f 4f 97 52 83
b4 1f 00 4f 0d 0e 00 00 07 80 91 87 8f 28 1f 8f
b5 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
adv0 failed to probe on isa0
aha0 failed to probe on isa0
aic0 failed to probe on isa0
ata2 failed to probe at port 0x1f0 irq 14 on isa0
ata3 failed to probe at port 0x170 irq 15 on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x3d0000
atkbd1: unable to allocate IRQ
psm0: current command byte:0065
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model GlidePoint, device ID 0-00, 2 buttons
psm0: config:00000000, flags:00000000, packet size:3
psm0: syncmask:c0, syncbits:00
bt0 failed to probe on isa0
cs0 failed to probe at port 0x300 on isa0
ed0 failed to probe at port 0x280 iomem 0xd8000 irq 10 on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
fe0 failed to probe at port 0x300 on isa0
ie0 failed to probe at port 0x300 iomem 0xd0000 irq 10 on isa0
le0 failed to probe at port 0x300 iomem 0xd0000 irq 5 on isa0
lnc0 failed to probe at port 0x280 irq 10 drq 0 on isa0
pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0
pcic1: not probed (disabled)
pcm1 failed to probe at irq 10 drq 1 on isa0
pmtimer0 on isa0
ppc0: parallel port found at 0x378
ppc0: using extended I/O port range
ppc0: ECP SPP ECP+EPP SPP
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
sc1: no video adapter found.
sc1: <System console> failed to probe at flags 0x100 on isa0
sio0: irq maps: 0x201 0x211 0x201 0x201
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: irq maps: 0x201 0x201 0x201 0x201
sio1: probe failed test(s): 0 1 2 4 6 7 9
sio1 failed to probe at port 0x2f8-0x2ff irq 3 on isa0
sio2: not probed (disabled)
sio3: configured irq 9 not in bitmap of probed irqs 0
sio3: irq maps: 0x201 0x201 0x201 0x201
sio3: probe failed test(s): 0 1 2 4 6 7 9
sio3 failed to probe at port 0x2e8-0x2ef irq 9 on isa0
sn0 failed to probe at port 0x300 irq 10 on isa0
vga1: <Generic ISA VGA> failed to probe on isa0
vt0 failed to probe on isa0
isa_probe_children: probing PnP devices
unknown: <PNP0c01> can't assign resources
unknown: <PNP0c01> at port
0x800-0x83f,0x840-0x84f,0x600-0x67f,0x680-0x6ff,0x880-0x88f,0x3f0-0x3f1 iomem
0-0x9ffff,0x100000-0x7ffffff,0xf0000-0xfffff,0xfffe0000-0xffffffff,0x100a0000-0x100fffff
on isa0
unknown: <PNP0303> can't assign resources
unknown: <PNP0303> at port 0x60 on isa0
unknown: <PNP0f13> can't assign resources
unknown: <PNP0f13> at irq 12 on isa0
unknown: <PNP0800> failed to probe at port 0x61 on isa0
unknown: <PNP0e03> can't assign resources
unknown: <PNP0e03> at port 0x3e0-0x3e1 irq 5 on isa0
unknown: <PNP0501> can't assign resources
unknown: <PNP0501> at port 0x3f8-0x3ff on isa0
unknown: <SMCf010> can't assign resources
unknown: <SMCf010> at port 0x3f8-0x3ff on isa0
unknown: <PNP0401> can't assign resources
unknown: <PNP0401> at port 0x378-0x37f on isa0
unknown: <PNP0700> can't assign resources
unknown: <PNP0700> at port 0x3f2-0x3f5 on isa0
BIOS Geometries:
0:03fefe3f 0..1022=1023 cylinders, 0..254=255 heads, 1..63=63 sectors
0 accounted for
Device configuration finished.
bpf: ppp0 attached
bpf: lo0 attached
ad0: success setting UDMA2 on Intel chip
Creating DISK ad0
ad0: <IBM-DJSA-220/JS4OAC0A> ATA-5 disk at ata0-master
ad0: 19077MB (39070080 sectors), 38760 C, 16 H, 63 S, 512 B
ad0: 16 secs/int, 1 depth queue, UDMA33
ad0: piomode=4 dmamode=2 udmamode=4 cblid=1
Mounting root from ufs:/dev/ad0s4a
ad0s1: type 0x7, start 63, end = 10779614, size 10779552 : OK
ad0s2: type 0x6, start 10779615, end = 25687934, size 14908320 : OK
ad0s3: type 0xa5, start 27696060, end = 39070079, size 11374020 : OK
ad0s4: type 0xa5, start 25687935, end = 27696059, size 2008125 : OK
pccbb0: card inserted: event=0x00000000, state=30000820
pccbb0: pccbb_power: CARD_VCC_0V and CARD_VPP_0V [44]
pccbb0: pccbb_power: CARD_VCC_3V and CARD_VPP_VCC [11]
found-> vendor=0x115d, dev=0x0003, revid=0x03
class=02-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0xa8 (5040 ns), mingnt=0x14 (5000 ns), maxlat=0x28 (10000 ns)
intpin=a, irq=0
TUPLE: LINKTARGET [3]: 43 49 53
Product version: 5.0
Product name: Xircom | CardBus Ethernet 10/100 + Modem 56 | CBEM56G | 1.03 |
TUPLE: Unknown(0x88) [4]: b8 d5 98 00
TUPLE: Unknown(0x8a) [12]: 39 30 30 33 57 47 39 38 44 35 42 38
TUPLE: Unknown(0x8b) [4]: 01 00 00 00
Manufacturer ID: 0501030181
TUPLE: DATE [4]: d7 72 4a 29
Functions: Network Adaptor, Multi-Functioned
Function Extension: 04060010a498d5b8
Function Extension: 0102
Function Extension: 0280969800
Function Extension: 0200e1f505
Function Extension: 0301
Function Extension: 0303
Function Extension: 0501
TUPLE: DEVICE_OC [4]: 02 4f 02 ff
cardbus0: Opening BAR: type=IO, bar=10, len=0080
cardbus0: Opening BAR: type=MEM, bar=14, len=0080
cardbus0: Opening BAR: type=MEM, bar=18, len=0100
cardbus0: Invalid BAR number: 27(06)
TUPLE: CONFIG_CB [7]: 03 02 03 01 00 00 ff
TUPLE: CFTABLE_ENTRY_CB [8]: 41 b0 b0 bc 8e 0e fb 04
TUPLE: CFTABLE_ENTRY_CB [9]: 02 b8 02 b0 bc 8e 1c fb 04
TUPLE: NO_LINK [0]:
CIS reading done
cardbus0: Non-prefetchable memory at 44000000-4400017f
cardbus0: Non-prefetchable memory rid=18 at 44000000-440000ff (100)
cardbus0: Non-prefetchable memory rid=14 at 44000100-4400017f (80)
cardbus0: IO port at 1000-107f
cardbus0: IO port rid=10 at 1000-107f
dc0: <Xircom X3201 10/100BaseTX> port 0x1000-0x107f mem
0x44000000-0x440000ff,0x44000100-0x4400017f irq 11 at device 0.0 on cardbus0
dc0: Ethernet address: 4a:29:21:02:06:00
miibus0: <MII bus> on dc0
tdkphy0: <TDK 78Q2120 media interface> on miibus0
tdkphy0: OUI 0x00c039, model 0x0014, rev. 11
tdkphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
bpf: dc0 attached
found-> vendor=0x115d, dev=0x0103, revid=0x03
class=07-00-02, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0210, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=0
TUPLE: LINKTARGET [3]: 43 49 53
Product version: 5.0
Product name: Xircom | CardBus Ethernet 10/100 + Modem 56 | CBEM56G | 1.03 |
TUPLE: Unknown(0x88) [4]: b8 d5 98 00
TUPLE: Unknown(0x8a) [12]: 00 00 00 00 00 00 00 00 00 00 00 00
TUPLE: Unknown(0x8b) [4]: 01 00 00 00
Manufacturer ID: 0501001081
TUPLE: DATE [4]: d7 72 4a 29
Functions: Serial Port, Multi-Functioned
Function Extension: 00020f5c
Function Extension: 0206003f1c03030f070001b5
Function Extension: 1306000b000200b5
TUPLE: DEVICE_OC [4]: 02 4f 02 ff
cardbus0: Opening BAR: type=IO, bar=10, len=0002
cardbus0: Opening BAR: type=MEM, bar=14, len=0002
cardbus0: Opening BAR: type=MEM, bar=18, len=0100
cardbus0: Invalid BAR number: 27(06)
TUPLE: CONFIG_CB [7]: 03 02 f3 00 00 00 ff
TUPLE: CFTABLE_ENTRY_CB [9]: 41 b8 02 b0 bc 8e 0e fb 04
TUPLE: CFTABLE_ENTRY_CB [8]: 02 b0 b0 bc 8e 0e fb 04
TUPLE: NO_LINK [0]:
CIS reading done
cardbus0: Non-prefetchable memory at 44000200-44000301
cardbus0: Non-prefetchable memory rid=18 at 44000200-440002ff (100)
cardbus0: Non-prefetchable memory rid=14 at 44000300-44000301 (2)
cardbus0: IO port at 1080-1081
cardbus0: IO port rid=10 at 1080-1081
sio4: irq maps: 0x201 0x201 0x201 0x201
sio4: probe failed test(s): 0 1 2 4 6 7 9
sio4: irq maps: 0x201 0x201 0x201 0x201
sio4: probe failed test(s): 0 1 2 4 6 7 9
cardbus0: <unknown card> (vendor=0x115d, dev=0x0103) at 0.1 irq 11
start_init: trying /sbin/init
cardbus1: detach_card: no card to detach!
pccbb1: pccbb_power: CARD_VCC_0V and CARD_VPP_0V [44]
link_elf: symbol pfil_add_hook undefined
cstsevent occures, 0x30000868
splash: image decoder found: green_saver
Linux ELF exec handler installed
#
# NEWCARD -- efforts at porting newconfig pccard/cardbus code to newbus
#
# This is a new implementation of pccard and cardbus support. It works
# for many folks right now. Some folks still have issues. The support
# around the edges isn't as complete as the previous pccard system.
#
# For more information on this file, please read the handbook section on
# Kernel Configuration Files:
#
# http://www.FreeBSD.org/handbook/kernelconfig-config.html
#
# The handbook is also available locally in /usr/share/doc/handbook
# if you've installed the doc distribution, otherwise always see the
# FreeBSD World Wide Web server (http://www.FreeBSD.org/) for the
# latest information.
#
# An exhaustive list of options and more detailed explanations of the
# device lines is also present in the NOTES configuration file. If you are
# in doubt as to the purpose or necessity of a line, check first in NOTES.
#
# $FreeBSD: src/sys/i386/conf/NEWCARD,v 1.50 2001/08/06 16:04:39 nate Exp $
machine i386
cpu I686_CPU
ident NEWCARD
maxusers 128
#To statically compile in device wiring instead of /boot/device.hints
#hints "NEWCARD.hints" #Default places to look for devices.
makeoptions DEBUG=-g #Build kernel with gdb(1) debug symbols
options MATH_EMULATE #Support for x87 emulation
options INET #InterNETworking
#options INET6 #IPv6 communications protocols
options FFS #Berkeley Fast Filesystem
options SOFTUPDATES #Enable FFS soft updates support
options MD_ROOT #MD is a potential root device
options NFS #Network Filesystem
options NFS_ROOT #NFS usable as root device, NFS required
options MSDOSFS #MSDOS Filesystem
options CD9660 #ISO 9660 Filesystem
options PROCFS #Process filesystem
options COMPAT_43 #Compatible with BSD 4.3 [KEEP THIS!]
options SCSI_DELAY=15000 #Delay (in ms) before probing SCSI
options UCONSOLE #Allow users to grab the console
#options USERCONFIG #boot -c editor
#options VISUAL_USERCONFIG #visual boot -c editor
options KTRACE #ktrace(1) support
options SYSVSHM #SYSV-style shared memory
options SYSVMSG #SYSV-style message queues
options SYSVSEM #SYSV-style semaphores
options P1003_1B #Posix P1003_1B real-time extensions
options _KPOSIX_PRIORITY_SCHEDULING
options KBD_INSTALL_CDEV # install a CDEV entry in /dev
# Debugging for use in -current
options DDB
options INVARIANTS
options INVARIANT_SUPPORT
options WITNESS
# To make an SMP kernel, the next two are needed
#options SMP # Symmetric MultiProcessor Kernel
#options APIC_IO # Symmetric (APIC) I/O
device isa
#device eisa
device pci
# Floppy drives
device fdc
# ATA and ATAPI devices
device ata
device atadisk # ATA disk drives
device atapicd # ATAPI CDROM drives
device atapifd # ATAPI floppy drives
#device atapist # ATAPI tape drives
options ATA_STATIC_ID #Static device numbering
# SCSI Controllers
#device ahb # EISA AHA1742 family
#device ahc # AHA2940 and onboard AIC7xxx devices
#device amd # AMD 53C974 (Tekram DC-390(T))
#device isp # Qlogic family
##device ncr # NCR/Symbios Logic
#device sym # NCR/Symbios Logic (newer chipsets + those of `ncr')
#device adv # Advansys SCSI adapters
#device adw # Advansys wide SCSI adapters
#device aha # Adaptec 154x SCSI adapters
#device aic # Adaptec 15[012]x SCSI adapters, AIC-6[23]60.
#device bt # Buslogic/Mylex MultiMaster SCSI adapters
#device ncv # NCR 53C500
#device nsp # Workbit Ninja SCSI-3
#device stg # TMC 18C30/18C50
# RAID controllers interfaced to the SCSI subsystem
#device asr # DPT SmartRAID V, VI and Adaptec SCSI RAID
#device dpt # DPT Smartcache III, IV - See NOTES for options!
#device mly # Mylex AcceleRAID/eXtremeRAID
# SCSI peripherals
device scbus # SCSI bus (required)
device da # Direct Access (disks)
device sa # Sequential Access (tape etc)
device cd # CD
device pass # Passthrough device (direct SCSI access)
# RAID controllers
#device aac # Adaptec FSA RAID
#device amr # AMI MegaRAID
#device ida # Compaq Smart RAID
#device mlx # Mylex DAC960 family
#device twe # 3ware ATA RAID
# atkbdc0 controls both the keyboard and the PS/2 mouse
device atkbdc 1 # At keyboard controller
device atkbd # at keyboard
device psm # psm mouse
device vga # VGA screen
# splash screen/screen saver
device splash
# syscons is the default console driver, resembling an SCO console
device sc 1
# Enable this for the pcvt (VT220 compatible) console driver
#device vt
#options XSERVER # support for X server on a vt console
#options FAT_CURSOR # start with block cursor
# Floating point support - do not disable.
device npx
# Power management support (see NOTES for more options)
#device apm
# Add suspend/resume support for the i8254.
device pmtimer
# Pcmcia and cardbus bridge support
device pccbb # cardbus (yenta) bridge
#device pccard
device cardbus
# Serial (COM) ports
device sio # 8250, 16[45]50 based serial ports
# Parallel port
device ppc
device ppbus # Parallel port bus (required)
device lpt # Printer
#device plip # TCP/IP over parallel
#device ppi # Parallel port interface device
##device vpo # Requires scbus and da
# PCI Ethernet NICs.
#device de # DEC/Intel DC21x4x (``Tulip'')
#device vx # 3Com 3c590, 3c595 (``Vortex'')
#device txp # 3Com 3cR990 (``Typhoon'')
# PCI Ethernet NICs that use the common MII bus controller code.
# NOTE: Be sure to keep the 'device miibus' line in order to use these NICs!
device miibus # MII bus support
device dc # DEC/Intel 21143 and various workalikes
#device fxp # Intel EtherExpress PRO/100B (82557, 82558)
#device pcn # AMD Am79C97x PCI 10/100 NICs
#device rl # RealTek 8129/8139
#device sf # Adaptec AIC-6915 (``Starfire'')
#device sis # Silicon Integrated Systems SiS 900/SiS 7016
#device ste # Sundance ST201 (D-Link DFE-550TX)
#device tl # Texas Instruments ThunderLAN
#device tx # SMC EtherPower II (83c170 ``EPIC'')
#device vr # VIA Rhine, Rhine II
#device wb # Winbond W89C840F
#device wx # Intel Gigabit Ethernet Card (``Wiseman'')
device xl # 3Com 3c90x (``Boomerang'', ``Cyclone'')
# ISA Ethernet NICs. pccard nics included.
#device cs # Crystal Semiconductor CS89x0 NIC
## 'device ed' requires 'device miibus'
#device ed # NE[12]000, SMC Ultra, 3c503, DS8390 cards
#device ex # Intel EtherExpress Pro/10 and Pro/10+
#device ep # Etherlink III based cards
#device fe # Fujitsu MB8696x based cards
#device sn # SMC's 9000 series of ethernet chips
#device xe # Xircom pccard ethernet
# The probe order of these is presently determined by i386/isa/isa_compat.c.
#device ie
#device le
#device lnc
# Wireless NIC cards
#device an # Aironet 4500/4800 802.11 wireless NICs.
#device awi # BayStack 660 and others
#device wi # WaveLAN/IEEE 802.11 wireless NICs.
#device wl # Older non 802.11 Wavelan wireless NIC.
# Pseudo devices - the number indicates how many units to allocate.
device random # Entropy device
device loop # Network loopback
device ether # Ethernet support
device sl # Kernel SLIP
device ppp 1 # Kernel PPP
device tun # Packet tunnel.
device pty # Pseudo-ttys (telnet etc)
device md # Memory "disks"
#device gif # IPv6 and IPv4 tunneling
#device faith 1 # IPv6-to-IPv4 relaying (translation)
# The `bpf' device enables the Berkeley Packet Filter.
# Be aware of the administrative consequences of enabling this!
device bpf # Berkeley packet filter
# USB support
#device uhci # UHCI PCI->USB interface
#device ohci # OHCI PCI->USB interface
device usb # USB Bus (required)
#device udbp # USB Double Bulk Pipe devices
device ugen # Generic
device uhid # "Human Interface Devices"
#device ukbd # Keyboard
#device ulpt # Printer
device umass # Disks/Mass storage - Requires scbus and da
#device ums # Mouse
#device urio # Diamond Rio 500 MP3 player
#device uscanner # Scanners
# USB Ethernet, requires mii
#device aue # ADMtek USB ethernet
#device cue # CATC USB ethernet
#device kue # Kawasaki LSI USB ethernet
Many thanks,
--
Vladimir
To Unsubscribe: send mail to [EMAIL PROTECTED]
with "unsubscribe freebsd-current" in the body of the message
