PseudoCylon wrote:
> ----- Original Message ----
>
>>>>
>>>>
>>> Well, the patch is working (sort of). Old driver wouldn't let you ping
>>> anywhere.
>>>
>>> Replies are taking awfully long. One of them took 5 sec. This could be a
>>> different issue.
>>>
>>> Can you try a few thing? (Unfortunately, everything is working on my side.)
>>> * Before ping from rspro, does ping from macbook to 192.168.1.42 (wlan0)
>>> work?
>>>
>>>
>> No. I will check again and let you know.
>>
>>
>>> * If you give IP address to only bridge0, does it make any difference?
>>>
>>>
>> I will let you know after testing.
>>
>>
>>> * Does it make any difference if use rspro without 192.168.1.7 (if
>>> possible)?
>>>
>>>
>> 192.168.1.7 is just my freebsd laptop.
>>
>>
>
> Hello,
>
> More questions.
>
> Is freebsd laptop working fine with wlan, or is it connected to ethernet port?
>
Connected to ethernet port.
> Does adsl modem still freeze?
>
Yes.
> Normally, when you ping from macbook to modem, there will be arp pakets
> 'who-has modem tell macbook' and
> 'modem is-at xx:xx...'
> Do you see these at wlan0 on rspro?
>
I see it.
...
19:02:52.519830 ARP, Ethernet (len 6), IPv4 (len 4), Request who-has
192.168.1.1 tell 192.168.1.50, length 28
0x0000: ffff ffff ffff 0026 bb17 f661 0806 0001
0x0010: 0800 0604 0001 0026 bb17 f661 c0a8 0132
0x0020: 0000 0000 0000 c0a8 0101
19:02:52.520118 ARP, Ethernet (len 6), IPv4 (len 4), Reply 192.168.1.1
is-at 00:30:54:62:3d:24 (oui Unknown), length 46
0x0000: 0026 bb17 f661 0030 5462 3d24 0806 0001
0x0010: 0800 0604 0002 0030 5462 3d24 c0a8 0101
0x0020: 0026 bb17 f661 c0a8 0132 0000 0000 0000
0x0030: 0000 0000 0000 0000 0000 0000
I will test the rest and let you know.
Ganbold
> If rspro can ping patch should be working, but let's make sure it is. Please
> before starting hostapd,
> sysctl hw.usb.run.debug=1
> (If the driver is not compiled with kernel, please apply a patch attached.)
> When hostapd is started, it will print out
>
> Starting hostapd.
> Configuration file: /etc/hostapd.conf
> Using interface wlan0 with hwaddr 00:22:cf:03:e0:30 and ssid 'bsd'
> run_key_set: cmdq_store=0
> run_key_set_cb: associd=0, keyix=1, mode=3, type=group, tx=on, rx=off
> run_stop: All Tx cleared
> run_newstate: INIT -> INIT
> run_newstate: INIT -> SCAN
> ... omit some lines ...
>
> Please confirm there is
> run_key_set_cb: associd=0, mode=3, ...
> And, associd is '0' (This was the problem before. So, encryption with group
> key failed.)
>
> When macbook associates with AP, it will print
>
> run_newassoc: cmdq_store=2
> run_newassoc: new assoc isnew=1 associd=c001 addr=00:26:bb:17:f6:61
> run_newassoc: rate=0x82 ridx=0 ctl_ridx=0
> ... omit some lines ...
> run_newassoc: rate=0x6c ridx=11 ctl_ridx=8
> run_newassoc: rate=2, mgmt_ridx=0
> run_key_set: cmdq_store=3
> run_key_set_cb: associd=c001, keyix=0, mode=4, type=pairwise, tx=on, rx=on
>
> Please confirm there is
> run_key_set_cb: associd=c001, mode=4, ...
> And associd isn't '0'.
>
> If not, I need to fix the driver. If things go accordingly, please compare
> the mode. With your config, group key uses TKIP (mode 3) and pairwise key
> uses CCMP (mode 4). And very first arp who-has packet uses group key and
> other use pairwise key. Maybe, macbook doesn't like mixing the mode. So,
> please
> tcpdump -vvv -xxx -i wlan0 'arp'
> and check if any packet with address of all 'ff'. is sent/received alright.
> All 'ff 'means using group key. Others use pairwise key. All 'ff is easy to
> see in output of tcpdump. Or, you can chose one of them, CCMP or TKIP for
> 'wpa_pairwise=' and see if it makes any difference.
>
>
> Sorry for too many questions. It is working fine here, again.
> AK
>
> --patch Only needed if the driver is not compiled with the kernel--
>
> diff --git a/dev/usb/wlan/if_run.c b/dev/usb/wlan/if_run.c
> index e4fc8d2..65c1dab 100644
> --- a/dev/usb/wlan/if_run.c
> +++ b/dev/usb/wlan/if_run.c
> @@ -69,6 +69,7 @@ __FBSDID("$FreeBSD: src/sys/dev/usb/wlan/if_run.c,v 1.11
> 2010/06/14 23:01:50 jki
> #include "usbdevs.h"
>
> #define USB_DEBUG_VAR run_debug
> +#define USB_DEBUG
> #include <dev/usb/usb_debug.h>
>
> #include "if_runreg.h"
>
> --end patch--
> only one line to add
>
>
>
>
>
--
I disagree with what you say, but will defend to the death your right to
tell such LIES!
_______________________________________________
freebsd-current@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-current
To unsubscribe, send any mail to "freebsd-current-unsubscr...@freebsd.org"
