On Sat, 12 Feb 2000, Doug Rabson wrote:
> Could you send a verbose dmesg (boot -v). I think we need to add a quirk
> for the NetFinity.
Unfortunately I'm currently remote, and I don't yet have it set up for a
serial console. I do have a verbose boot from before the change in
messages, if that is sufficient. If not, would you like one from 1.5[45]?
Copyright (c) 1992-2000 The FreeBSD Project.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
FreeBSD 4.0-CURRENT #0: Wed Feb 9 04:55:17 MST 2000
[EMAIL PROTECTED]:/usr/src/sys/compile/BLUE
Calibrating clock(s) ... TSC clock: 198944384 Hz, i8254 clock: 1193164 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz
CLK_USE_TSC_CALIBRATION not specified - using old calibration method
CPU: Pentium Pro (198.95-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x619 Stepping = 9
Features=0xfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV>
real memory = 268435456 (262144K bytes)
Physical memory chunk(s):
0x00001000 - 0x0009efff, 647168 bytes (158 pages)
0x00334000 - 0x0fff5fff, 265035776 bytes (64706 pages)
avail memory = 257114112 (251088K bytes)
Programming 16 pins in IOAPIC #0
IOAPIC #0 intpin 2 -> irq 0
SMP: CPU0 apic_initialize():
lint0: 0x00000700 lint1: 0x00010400 TPR: 0x00000010 SVR: 0x000001ff
FreeBSD/SMP: Multiprocessor motherboard
cpu0 (BSP): apic id: 0, version: 0x00040011, at 0xfec08000
cpu1 (AP): apic id: 4, version: 0x00040011, at 0xfec08000
cpu2 (AP): apic id: 1, version: 0x00040011, at 0xfec08000
cpu3 (AP): apic id: 2, version: 0x00040011, at 0xfec08000
io0 (APIC): apic id: 14, version: 0x000f0011, at 0xfec00000
bios32: Found BIOS32 Service Directory header at 0xc00fd060
bios32: Entry = 0xfd070 (c00fd070) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0xd091
pnpbios: Found PnP BIOS data at 0xc00fa2e0
pnpbios: Entry = f0000:a3c0 Rev = 1.0
Other BIOS signatures found:
ACPI: 00000000
Preloaded elf kernel "kernel" at 0xc0318000.
Preloaded userconfig_script "/boot/kernel.conf" at 0xc03180a8.
ccd0-1: Concatenated disk drivers
Pentium Pro MTRR support enabled
md0: Malloc disk
Creating DISK md0
Math emulator present
SMP: CPU0 bsp_apic_configure():
lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000010 SVR: 0x000001ff
pci_open(1): mode 1 addr port (0x0cf8) is 0x8000a0ac
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14
[class=000000] 15 [class=ff0000] 16 17 18 19 20 [class=050000] [hdr=00] is there
(id=84c58086)
npx0: <math processor> on motherboard
npx0: INT 16 interface
pci_open(1): mode 1 addr port (0x0cf8) is 0x00000000
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14
[class=000000] 15 [class=ff0000] 16 17 18 19 20 [class=050000] [hdr=00] is there
(id=84c58086)
pcib0: <Intel 82454KX/GX (Orion) host to PCI bridge> on motherboard
found-> vendor=0x8086, dev=0x0482, revid=0x15
class=00-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
found-> vendor=0x8086, dev=0x0008, revid=0x00
class=ff-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
map[10]: type 1, range 32, base fec01000, size 10
map[14]: type 1, range 32, base fffffc00, size 10
map[18]: type 1, range 32, base fffffc00, size 10
map[1c]: type 1, range 32, base fffffc00, size 10
map[20]: type 1, range 32, base fffffc00, size 10
map[24]: type 1, range 32, base fffffc00, size 10
found-> vendor=0x8086, dev=0x84c5, revid=0x05
class=05-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
found-> vendor=0x8086, dev=0x84c4, revid=0x06
class=06-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
found-> vendor=0x8086, dev=0x84c4, revid=0x06
class=06-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
pci0: <PCI bus> on pcib0
isab0: <Intel 82375EB PCI-EISA bridge> at device 14.0 on pci0
eisa0: <EISA bus> on isab0
mainboard0: <INT31c0 (System Board)> on eisa0 slot 0
isa0: <ISA bus> on isab0
chip0: <> mem
0xfffffc00-0xffffffff,0xfffffc00-0xffffffff,0xfffffc00-0xffffffff,0xfffffc00-0xffffffff,0xfffffc00-0xffffffff,0xfec01000-0xfec013ff
at device 15.0 on
chip1: <Intel 82453KX/GX (Orion) PCI memory controller> at device 20.0 on pci0
pci_open(1): mode 1 addr port (0x0cf8) is 0x00000000
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14
[class=000000] 15 [class=ff0000] 16 17 18 19 20 [class=050000] [hdr=00] is there
(id=84c58086)
pcib1: <Intel 82454KX/GX (Orion) host to PCI bridge> on motherboard
found-> vendor=0x9004, dev=0x8078, revid=0x00
class=01-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=11
map[10]: type 1, range 32, base 0000fc00, size 8
map[14]: type 1, range 32, base fe8ff000, size 12
found-> vendor=0x9004, dev=0x8078, revid=0x00
class=01-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=9
map[10]: type 1, range 32, base 0000f800, size 8
map[14]: type 1, range 32, base fe8fe000, size 12
found-> vendor=0x1106, dev=0x3043, revid=0x06
class=02-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=10
map[10]: type 1, range 32, base 0000f480, size 7
map[14]: type 1, range 32, base fe8fdc00, size 7
pci1: <PCI bus> on pcib1
ahc0: <Adaptec aic7880 Ultra SCSI adapter> port 0xfc00-0xfcff mem
0xfe8ff000-0xfe8fffff irq 11 at device 11.0 on pci1
ahc0: Reading SEEPROM...checksum error
ahc0: No SEEPROM available.
ahc0: Using left over BIOS settings
ahc0: aic7880 Wide Channel A, SCSI Id=7, 16/255 SCBs
ahc0: Downloading Sequencer Program... 412 instructions downloaded
ahc1: <Adaptec aic7880 Ultra SCSI adapter> port 0xf800-0xf8ff mem
0xfe8fe000-0xfe8fefff irq 9 at device 12.0 on pci1
ahc1: Reading SEEPROM...checksum error
ahc1: No SEEPROM available.
ahc1: Using left over BIOS settings
ahc1: aic7880 Wide Channel A, SCSI Id=7, 16/255 SCBs
ahc1: Downloading Sequencer Program... 412 instructions downloaded
vr0: <VIA VT3043 Rhine I 10/100BaseTX> port 0xf480-0xf4ff mem 0xfe8fdc00-0xfe8fdc7f
irq 10 at device 14.0 on pci1
vr0: Ethernet address: 00:50:ba:ab:85:18
miibus0: <MII bus> on vr0
amphy0: <DM9101 10/100 media interface> on miibus0
amphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
bpf: vr0 attached
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <keyboard controller (i8042)> at port 0x60-0x6f on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0065
atkbd: keyboard ID 0x41ab (2)
kbdc: RESET_KBD return code:00fa
kbdc: RESET_KBD status:00aa
kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000
psm0: current command byte:0065
kbdc: TEST_AUX_PORT status:0000
kbdc: RESET_AUX return code:00fa
kbdc: RESET_AUX status:00aa
kbdc: RESET_AUX ID:0000
psm: status 00 02 64
psm: status 00 03 06
psm: status 00 33 55
psm: data 18 ff 01
psm: status 00 02 64
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model NetMouse, device ID 0-00, 3 buttons
psm0: config:00000000, flags:00000000, packet size:4
psm0: syncmask:c8, syncbits:08
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 07 80 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
EGA/VGA parameters to be used for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
sc0: <System console> on isa0
sc0: VGA <9 virtual consoles, flags=0x200>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
sio0: irq maps: 0x41 0x51 0x41 0x41
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1: irq maps: 0x41 0x49 0x41 0x41
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
sio2: configured irq 5 not in bitmap of probed irqs 0
sio2: irq maps: 0x41 0x41 0x41 0x41
sio2: probe failed test(s): 0 1 2 4 6 7 9
sio3: not probed (disabled)
ppc0: parallel port found at 0x378
ppc0: ECP SPP ECP+EPP SPP
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
ppi0: <Parallel I/O> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
plip0: <PLIP network interface> on ppbus0
bpf: lp0 attached
isa_probe_children: probing PnP devices
SMP: enabled INTs: 1, 3, 4, 6, 7, 9, 10, 11, 12, apic_imen: 0x00ffe125
BIOS Geometries:
0:03fefe3f 0..1022=1023 cylinders, 0..254=255 heads, 1..63=63 sectors
0 accounted for
Device configuration finished.
APIC_IO: routing 8254 via IOAPIC #0 intpin 2
bpf: lo0 attached
Waiting 10 seconds for SCSI devices to settle
(noperiph:ahc0:0:-1:-1): SCSI bus reset delivered. 0 SCBs aborted.
(noperiph:ahc1:0:-1:-1): SCSI bus reset delivered. 0 SCBs aborted.
SMP: AP CPU #1 Launched!
SMP: CPU1 apic_initialize():
lint0: 0x00010700 lint1: 0x00010400 TPR: 0x00000010 SVR: 0x000001ff
SMP: AP CPU #2 Launched!
SMP: CPU2 apic_initialize():
lint0: 0x00010700 lint1: 0x00010400 TPR: 0x00000010 SVR: 0x000001ff
SMP: AP CPU #3 Launched!
SMP: CPU3 apic_initialize():
lint0: 0x00010700 lint1: 0x00010400 TPR: 0x00000010 SVR: 0x000001ff
Sending WDTR!
ahc0: target 1 using 16bit transfers
ahc0: target 1 synchronous at 20.0MHz, offset = 0x8
Sending SDTR!
ahc0: target 1 using asynchronous transfers
ahc0: target 1 synchronous at 20.0MHz, offset = 0x8
Creating DISK da0
pass0 at ahc0 bus 0 target 1 lun 0
pass0: <TANDEM 4618-1\003+\002\025\202\010\002\025\227\350 03A1> Fixed Direct Access
SCSI-3 device
pass0: Serial Number 68165104GK
pass0: 40.000MB/s transfers (20.000MHz, offset 8, 16bit)
pass1 at ahc0 bus 0 target 15 lun 0
pass1: <SDR GEM200 2> Fixed Processor SCSI-2 device
pass1: Serial Number 1
pass1: 3.300MB/s transfers
pass1 at ahc0 bus 0 target 15 lun 0
pass1: <SDR GEM200 2> Fixed Processor SCSI-2 device
pass1: Serial Number 1
pass1: 3.300MB/s transfers
da0 at ahc0 bus 0 target 1 lun 0
da0: <TANDEM 4618-1\003+\002\025\202\010\002\025\227\350 03A1> Fixed
Direct Access SCSI-3 device
da0: Serial Number 68165104GK
da0: 40.000MB/s transfers (20.000MHz, offset 8, 16bit)
da0: 17501MB (35843670 512 byte sectors: 64H 32S/T 17501C)
Mounting root from ufs:/dev/da0s1a
da0s1: type 0xa5, start 63, end = 35841014, size 35840952 : OK
start_init: trying /sbin/init
splash: image decoder found: logo_saver
Later...... <Doug>
To Unsubscribe: send mail to [EMAIL PROTECTED]
with "unsubscribe freebsd-current" in the body of the message
