Last cvs was a few hours ago and world was installed.
A kernel built from this cvs hangs dead-hard when moused runs from
rc.i386 and no mouse is plugged into the psm0 port
device psm0 at atkbdc? irq 12
The moused config is:
moused_enable="NO" # Run the mouse daemon.
moused_type="mousesystems" # See man page for rc.conf(5) for available settings.
moused_port="/dev/cuaa0" # Set to your mouse port.
moused_flags="" # Any additional flags to moused.
I haven't tested if the kernel hangs when a mouse IS actually plugged
in, but by not running moused at all the kernel so far is fine otherwise.
Last kernel built was Jan 24, and it works fine when no mouse is
plugged in.
A log of a verbose startup follows below.
Regards,
Scott
--
Scott G. Akmentins-Taylor InterNet: [EMAIL PROTECTED]
MRY Systems [EMAIL PROTECTED]
(Skots Gregorijs Akmentins-Teilors -- just call me "Skots")
----- Labak miris neka sarkans -----
------------
Copyright (c) 1992-2000 The FreeBSD Project.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
FreeBSD 4.0-CURRENT #1: Fri Feb 11 14:10:38 PST 2000
[EMAIL PROTECTED]:/usr/src/sys/compile/PORTLEY2
Calibrating clock(s) ... i8254 clock: 1193284 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz
CPU: Cyrix 6x86 (486-class CPU)
Origin = "CyrixInstead" DIR=0x1731 Stepping=1 Revision=7
real memory = 67108864 (65536K bytes)
Physical memory chunk(s):
0x00001000 - 0x0009ffff, 651264 bytes (159 pages)
0x0036e000 - 0x03febfff, 63430656 bytes (15486 pages)
bios32: Found BIOS32 Service Directory header at 0xc00fae40
bios32: Entry = 0xfb2c0 (c00fb2c0) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0xb2f0
pnpbios: Found PnP BIOS data at 0xc00fc070
pnpbios: Entry = f0000:c098 Rev = 1.0
Other BIOS signatures found:
ACPI: 00000000
Preloaded elf kernel "nkernel" at 0xc0355000.
pci_open(1): mode 1 addr port (0x0cf8) is 0x8000005c
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=70308086)
npx0: <math processor> on motherboard
npx0: INT 16 interface
pci_open(1): mode 1 addr port (0x0cf8) is 0x00000000
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=70308086)
pcib0: <Host to PCI bridge> on motherboard
found-> vendor=0x8086, dev=0x7030, revid=0x02
class=06-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
found-> vendor=0x8086, dev=0x7000, revid=0x01
class=06-01-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
found-> vendor=0x8086, dev=0x7010, revid=0x00
class=01-01-80, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
map[20]: type 1, range 32, base 0000f000, size 4
found-> vendor=0x8086, dev=0x7020, revid=0x01
class=0c-03-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=d, irq=11
map[20]: type 1, range 32, base 00006000, size 5
found-> vendor=0x9004, dev=0x8178, revid=0x00
class=01-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=12
map[10]: type 1, range 32, base 00006100, size 8
map[14]: type 1, range 32, base e4000000, size 12
found-> vendor=0x5333, dev=0x8811, revid=0x54
class=03-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=12
map[10]: type 1, range 32, base e0000000, size 26
found-> vendor=0x10b7, dev=0x9050, revid=0x00
class=02-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=11
map[10]: type 1, range 32, base 00006200, size 6
pci0: <PCI bus> on pcib0
PCI Concurrency: enabled
Cache: 256K pipelined-burst secondary; L1 enabled
DRAM: no memory hole, 66 MHz refresh
Read burst timing: x-2-2-2/x-3-3-3
Write burst timing: x-2-2-2
RAS-CAS delay: 3 clocks
isab0: <Intel 82371SB PCI to ISA bridge> at device 7.0 on pci0
I/O Recovery Timing: 8-bit 3.5 clocks, 16-bit 3.5 clocks
Extended BIOS: disabled
Lower BIOS: disabled
Coprocessor IRQ13: enabled
Mouse IRQ12: disabled
Interrupt Routing: A: IRQ12, B: IRQ12, C: disabled, D: IRQ11
MB0: IRQ15, MB1:
isa0: <ISA bus> on isab0
ata-pci0: <Intel PIIX3 ATA controller> port 0xf000-0xf00f at device 7.1 on pci0
ata0: iobase=0x01f0 altiobase=0x03f6 bmaddr=0xf000
ata0: mask=03 status0=50 status1=00
ata0: mask=03 status0=50 status1=00
ata0: devices = 0x1
ata0 at 0x01f0 irq 14 on ata-pci0
ata1: iobase=0x0170 altiobase=0x0376 bmaddr=0xf008
ata1: mask=00 status0=ff status1=ff
pci0: Intel 82371SB (PIIX3) USB controller (vendor=0x8086, dev=0x7020) at 7.2 irq 11
ahc0: <Adaptec 2940 Ultra SCSI adapter> port 0x6100-0x61ff mem 0xe4000000-0xe4000fff
irq 12 at device 17.0 on pci0
ahc0: Reading SEEPROM...done.
ahc0: internal 50 cable not present, internal 68 cable not present
ahc0: external cable not present
ahc0: BIOS eeprom is present
ahc0: High byte termination Enabled
ahc0: Low byte termination Enabled
ahc0: aic7880 Wide Channel A, SCSI Id=7, 16/255 SCBs
ahc0: Downloading Sequencer Program... 415 instructions downloaded
vga-pci0: <S3 Trio graphics accelerator> mem 0xe0000000-0xe3ffffff irq 12 at device
18.0 on pci0
xl0: <3Com 3c905-TX Fast Etherlink XL> port 0x6200-0x623f irq 11 at device 19.0 on pci0
xl0: Ethernet address: 00:10:4b:21:69:28
xl0: media options word: e040
xl0: found MII/AUTO
miibus0: <MII bus> on xl0
nsphy0: <DP83840 10/100 media interface> on miibus0
nsphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
bpf: xl0 attached
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
atkbdc0: <keyboard controller (i8042)> at port 0x60-0x6f on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0047
atkbd: keyboard ID 0x41ab (2)
kbdc: RESET_KBD return code:00fa
kbdc: RESET_KBD status:00aa
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000
psm0: current command byte:0047
kbdc: TEST_AUX_PORT status:0000
kbdc: RESET_AUX return code:00fe
kbdc: RESET_AUX return code:00fe
kbdc: RESET_AUX return code:00fe
kbdc: DIAGNOSE status:0055
kbdc: TEST_KBD_PORT status:0000
psm0: failed to reset the aux device.
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0e 0f 00 00 07 80 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
EGA/VGA parameters to be used for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
sc0: <System console> on isa0
sc0: VGA <12 virtual consoles, flags=0x200>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
aha0: status reg test failed ff
aha0: status reg test failed ff
aha0: status reg test failed ff
aha0: status reg test failed ff
aha0: status reg test failed ff
aha0: status reg test failed ff
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
sio0: irq maps: 0x41 0x51 0x41 0x41
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1: irq maps: 0x41 0x49 0x41 0x41
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
sio2: irq maps: 0x41 0x41 0x41 0x41
sio2 at port 0x1f8-0x1ff flags 0x705 on isa0
sio2: type 16550A (multiport)
sio3: irq maps: 0x41 0x41 0x41 0x41
sio3 at port 0x1e8-0x1ef flags 0x705 on isa0
sio3: type 16550A (multiport)
sio4: irq maps: 0x41 0x41 0x41 0x41
sio4 at port 0x2a8-0x2af flags 0x705 on isa0
sio4: type 16550A (multiport)
sio5: irq maps: 0x41 0x441 0x41 0x41
sio5 at port 0x1a8-0x1af irq 10 flags 0x705 on isa0
sio5: type 16550A (multiport)
sio6: configured irq 5 not in bitmap of probed irqs 0
sio6: irq maps: 0x41 0x41 0x41 0x41
sio6 at port 0x180-0x187 flags 0x901 on isa0
sio6: type 16550A (multiport)
sio7: configured irq 5 not in bitmap of probed irqs 0
sio7: irq maps: 0x41 0x41 0x41 0x41
sio7: probe failed test(s): 0 1 2 4 6 7 9
sio8: configured irq 5 not in bitmap of probed irqs 0
sio8: irq maps: 0x41 0x41 0x41 0x41
sio8 at port 0x190-0x197 flags 0x901 on isa0
sio8: type 16550A (multiport)
sio9: configured irq 5 not in bitmap of probed irqs 0
sio9: irq maps: 0x41 0x41 0x41 0x41
sio9 at port 0x198-0x19f irq 5 flags 0x901 on isa0
sio9: type 16550A (multiport master)
ed0 at port 0x300-0x31f iomem 0xd0000-0xd3fff irq 9 drq 0 on isa0
ed0: address 00:00:d4:00:24:d4, type WD8013EBT (16 bit)
bpf: ed0 attached
pca0 at port 0x40 on isa0
ppc0: parallel port found at 0x378
ppc0: ECP SPP ECP+EPP SPP
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/1 bytes threshold
pps0: <Pulse per second Timing Interface> on ppbus0
ppi0: <Parallel I/O> on ppbus0
pcfclock0: <PCF-1.0> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
plip0: <PLIP network interface> on ppbus0
bpf: lp0 attached
isa_probe_children: probing PnP devices
BIOS Geometries:
0:03fe0e3f 0..1022=1023 cylinders, 0..14=15 heads, 1..63=63 sectors
0 accounted for
Device configuration finished.
IP packet filtering initialized, divert enabled, rule-based forwarding enabled,
default to accept, logging limited to 100 packets/entry by default
DUMMYNET initialized (000106)
bpf: lo0 attached
Linux-ELF exec handler installed
BRIDGE 990810, have 4 interfaces
-- index 1 type 6 phy 0 addrl 6 addr 00.10.4b.21.69.28
-- index 2 type 6 phy 0 addrl 6 addr 00.00.d4.00.24.d4
Waiting 4 seconds for SCSI devices to settle
(noperiph:ahc0:0:-1:-1): SCSI bus reset delivered. 0 SCBs aborted.
ata0-master: success setting up WDMA2 mode on PIIX3 chip
ad0: <Maxtor 87000D8/TAVX3322> ATA-3 disk at ata0 as master
ad0: 6679MB (13678875 sectors), 14475 cyls, 15 heads, 63 S/T, 512 B/S
ad0: 16 secs/int, 1 depth queue, WDMA2
ad0: piomode=4 dmamode=2 udmamode=2 cblid=0
Creating DISK ad0
Creating DISK wd0
Mounting root from ufs:/dev/ad0s1a
ad0s1: type 0xa5, start 63, end = 13678874, size 13678812 : OK
start_init: trying /sbin/init
To Unsubscribe: send mail to [EMAIL PROTECTED]
with "unsubscribe freebsd-current" in the body of the message
