Hi,
after enabling the sym-driver I get drive-lockups after some time of accessing
the disks hanging on the sym-driver.
It seems that at least on disk hangs up (steady disk light) until a bus-reset
"(noperiph:sym0:0:-1:-1): SCSI BUS reset detected" occurs.
A difference between ncr and sym-driver is that the sym-driver probes the disks
as (excerpt from dmesg_sym.txt):
da1 at sym0 bus 0 target 1 lun 0
da1: <IBM DDRS-39130D DC1B> Fixed Direct Access SCSI-2 device
da1: 80.000MB/s transfers (40.000MHz, offset 15, 16bit), Tagged Queueing Enabled
da1: 8715MB (17850000 512 byte sectors: 255H 63S/T 1111C)
whereas the ncr-driver probes as (excerpt from dmesg_ncr.txt):
da1 at ncr0 bus 0 target 1 lun 0
da1: <IBM DDRS-39130D DC1B> Fixed Direct Access SCSI-2 device
da1: 40.000MB/s transfers (20.000MHz, offset 15, 16bit), Tagged Queueing Enabled
da1: 8715MB (17850000 512 byte sectors: 255H 63S/T 1111C)
Usually the IBM-FAQ suspects a cabling/termination Problem if one has a Problem
at 40MHZ.
But I have the 4 disks in a external case from kingston with a proper kable and
terminator and furthermore LVD-drives should have a better signal quality.
Furthermore I have zero problems at 20MHZ.
You can see in neg_before.txt the output of a 'camcontrol neg' which look right,
in neg_after.txt the output of the same command after the disk hang up and
the bus reseted.
neg_ncr.txt contains the output using the ncr-driver.
BTW: I have the same problems with the ncr-driver when using the kernel-config
parameter: SCSI_NCR_DFLT_SYNC=10
And now the question: Whats going wrong?
If it is the HW, how can it be proven? Are it the IBM-disks? Kabel?...
Is it the Software?
If I want to live with 40MB/s is there a knob to pre-set the speed in the
kernel-config or at boot-time?
Any clues?
Bye!
----
Michael Reifenberger
Plaut Software GmbH, R/3 Basis
g = 2
Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,XMM>
real memory = 268423168 (262132K bytes)
config> #flags wdc0 0xa0ffa0ff
Invalid command or syntax. Type `?' for help.
config> #flags wdc1 0xa0ffa0ff
Invalid command or syntax. Type `?' for help.
config> #irq isic0 10
Invalid command or syntax. Type `?' for help.
config> #pnp 1 0 bios enable port0 0x220 irq0 5 drq0 1 drq1 3
Invalid command or syntax. Type `?' for help.
config> #pnp 1 0 bios enable port0 0xd80 irq0 11
Invalid command or syntax. Type `?' for help.
config> pnp 1 1 os enable irq0 5 drq0 1 port0 0x220
Invalid command or syntax. Type `?' for help.
config> #iosiz npx0 262144
Invalid command or syntax. Type `?' for help.
config> quit
avail memory = 256712704 (250696K bytes)
Programming 24 pins in IOAPIC #0
IOAPIC #0 intpin 2 -> irq 0
FreeBSD/SMP: Multiprocessor motherboard
cpu0 (BSP): apic id: 1, version: 0x00040011, at 0xfee00000
cpu1 (AP): apic id: 0, version: 0x00040011, at 0xfee00000
io0 (APIC): apic id: 2, version: 0x00170011, at 0xfec00000
Preloaded elf kernel "kernel" at 0xc0362000.
Preloaded userconfig_script "/boot/kernel.conf" at 0xc036209c.
Preloaded elf module "bktr.ko" at 0xc03620ec.
VESA: v2.0, 8192k memory, flags:0x1, mode table:0xc02f5b42 (1000022)
VESA: Matrox Graphics Inc.
Pentium Pro MTRR support enabled
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Intel 82443BX (440 BX) host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
pcib1: <Intel 82443BX (440 BX) PCI-PCI (AGP) bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
vga-pci0: <Matrox model 0521 graphics accelerator> irq 16 at device 0.0 on pci1
isab0: <Intel 82371AB PCI to ISA bridge> at device 4.0 on pci0
isa0: <ISA bus> on isab0
pci0: Intel PIIX4 ATA controller (vendor=0x8086, dev=0x7111) at 4.1
uhci0: <Intel 82371AB/EB (PIIX4) USB controller> irq 19 at device 4.2 on pci0
usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
intpm0: <Intel 82371AB Power management controller> at device 4.3 on pci0
intpm0: I/O mapped e800
intpm0: intr IRQ 9 enabled revision 0
smbus0: <System Management Bus> on intsmb0
smb0: <SMBus general purpose I/O> on smbus0
intpm0: PM I/O mapped e400
ahc0: <Adaptec aic7890/91 Ultra2 SCSI adapter> irq 19 at device 6.0 on pci0
ahc0: aic7890/91 Wide Channel A, SCSI Id=7, 16/255 SCBs
pci0: unknown card (vendor=0x10b7, dev=0x9055) at 9.0 irq 19
bktr0: <BrookTree 878> irq 18 at device 10.0 on pci0
bktr0: Hauppauge Model 61344 D121
bktr0: Detected a MSP3410D-B4 at 0x80
Hauppauge WinCast/TV, Philips FR1216 PAL FM tuner, msp3400c stereo, remote control.
pci0: unknown card (vendor=0x109e, dev=0x0878) at 10.1 irq 18
ncr0: <ncr 53c895 fast40 wide scsi> irq 17 at device 11.0 on pci0
isic0: <ELSA MicroLink ISDN/PCI> irq 16 at device 12.0 on pci0
isic0: Error, IPAC version 2 unknown!
device_probe_and_attach: isic0 attach returned 6
isa0: too many memory rangesfdc0: <NEC 72065B or clone> at port 0x3f0-0x3f7 irq 6 drq
2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <keyboard controller (i8042)> at port 0x60-0x6f on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
vga0: <Generic ISA VGA> at port 0x3b0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> on isa0
sc0: VGA <16 virtual consoles, flags=0x200>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
sio2: configured irq 19 not in bitmap of probed irqs 0
sio3: configured irq 19 not in bitmap of probed irqs 0
ppc0 at port 0x378-0x37f irq 7 flags 0x40 on isa0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/9 bytes threshold
lpt0: <generic printer> on ppbus 0
lpt0: Interrupt-driven port
ppi0: <generic parallel i/o> on ppbus 0
unknown0: <ESS ES1868 Plug and Play AudioDrive> at port 0x800-0x807 on isa0
sbc0: <ESS ES1868> at port 0x220-0x22f,0x388-0x38b,0x330-0x331 irq 5 drq 1,0 on isa0
pcm0: <SB DSP 3.01 (ESS mode)> on sbc0
unknown1: <ESS ES1868 Plug and Play AudioDrive> at port 0x201 on isa0
unknown2: <ESS ES1868 Plug and Play AudioDrive> at port 0x168-0x16f,0x36e-0x36f irq 12
on isa0
unknown: <PNP0401> can't assign resources
unknown: <PNP0501> can't assign resources
unknown: <PNP0501> can't assign resources
unknown: <PNP0700> can't assign resources
unknown3: <PNP0c01> at iomem
0-0x9ffff,0x100000-0xfffffff,0xe8000-0xeffff,0xf0000-0xf3fff,0xf4000-0xf7fff,0xf8000-0xfffff,0xd3800-0xd3fff,0xfec00000-0xfec00fff
on isa0
unknown: <PNP0000> can't assign resources
unknown4: <PNP0100> at port 0x40-0x43 irq 0 on isa0
unknown5: <PNP0b00> at port 0x70-0x71 irq 8 on isa0
unknown: <PNP0303> can't assign resources
unknown6: <PNP0c04> at port 0xf0 irq 13 on isa0
unknown7: <PNP0200> at port 0-0xf,0x80-0x90,0x94-0x9f,0xc0-0xde drq 4 on isa0
unknown: <PNP0800> can't assign resources
unknown8: <PNP0a03> at port 0xcf8-0xcff on isa0
unknown: <PNP0c02> can't assign resources
APIC_IO: Testing 8254 interrupt delivery
APIC_IO: routing 8254 via IOAPIC #0 intpin 2
i4btrc: 4 ISDN trace device(s) attached
i4brbch: 4 raw B channel access device(s) attached
i4btel: 2 ISDN telephony interface device(s) attached
i4bipr: 4 IP over raw HDLC ISDN device(s) attached
i4bctl: ISDN system control port attached
i4bisppp: 4 ISDN SyncPPP device(s) attached
i4b: ISDN call control device attached
IP packet filtering initialized, divert enabled, rule-based forwarding disabled,
logging limited to 100 packets/entry by default
Waiting 2 seconds for SCSI devices to settle
SMP: AP CPU #1 Launched!
Mounting root from ufs:/dev/da0s1a
da3 at ncr0 bus 0 target 3 lun 0
da3: <IBM DDRS-39130D DC1B> Fixed Direct Access SCSI-2 device
da3: 40.000MB/s transfers (20.000MHz, offset 15, 16bit), Tagged Queueing Enabled
da3: 8715MB (17850000 512 byte sectors: 255H 63S/T 1111C)
da4 at ncr0 bus 0 target 4 lun 0
da4: <IBM DDRS-39130D DC1B> Fixed Direct Access SCSI-2 device
da4: 40.000MB/s transfers (20.000MHz, offset 15, 16bit), Tagged Queueing Enabled
da4: 8715MB (17850000 512 byte sectors: 255H 63S/T 1111C)
da1 at ncr0 bus 0 target 1 lun 0
da1: <IBM DDRS-39130D DC1B> Fixed Direct Access SCSI-2 device
da1: 40.000MB/s transfers (20.000MHz, offset 15, 16bit), Tagged Queueing Enabled
da1: 8715MB (17850000 512 byte sectors: 255H 63S/T 1111C)
da0 at ahc0 bus 0 target 0 lun 0
da0: <IBM DDRS-34560D DC1B> Fixed Direct Access SCSI-2 device
da0: 80.000MB/s transfers (40.000MHz, offset 15, 16bit), Tagged Queueing Enabled
da0: 4357MB (8925000 512 byte sectors: 255H 63S/T 555C)
da2 at ncr0 bus 0 target 2 lun 0
da2: <IBM DDRS-39130D DC1B> Fixed Direct Access SCSI-2 device
da2: 40.000MB/s transfers (20.000MHz, offset 15, 16bit), Tagged Queueing Enabled
da2: 8715MB (17850000 512 byte sectors: 255H 63S/T 1111C)
vinum: loaded
vinum: reading configuration from /dev/da1s1d
vinum: updating configuration from /dev/da2s1d
vinum: updating configuration from /dev/da3s1d
vinum: updating configuration from /dev/da4s1d
vinumioctl: invalid ioctl from process 16 (vinum): c0b84643
pci0: Intel PIIX4 ATA controller (vendor=0x8086, dev=0x7111) at 4.1
xl0: <3Com 3c905B-TX Fast Etherlink XL> irq 19 at device 9.0 on pci0
xl0: Ethernet address: 00:10:5a:d5:9b:43
pci0: unknown card (vendor=0x109e, dev=0x0878) at 10.1 irq 18
isic0: <ELSA MicroLink ISDN/PCI> irq 16 at device 12.0 on pci0
isic0: Error, IPAC version 2 unknown!
device_probe_and_attach: isic0 attach returned 6
miibus0: <MII bus> on xl0
xlphy0: <3Com internal media interface> on miibus0
xlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
cd0 at ahc0 bus 0 target 4 lun 0
cd0: <PLEXTOR CD-ROM PX-40TS 1.00> Removable CD-ROM SCSI-2 device
cd0: 20.000MB/s transfers (20.000MHz, offset 15)
cd0: cd present [327689 x 2048 byte records]
cd1 at ahc0 bus 0 target 6 lun 0
cd1: <YAMAHA CRW6416S 1.0c> Removable CD-ROM SCSI-2 device
cd1: 10.000MB/s transfers (10.000MHz, offset 15)
cd1: Attempt to query device size failed: NOT READY, Medium not present - tray closed
Copyright (c) 1992-2000 The FreeBSD Project.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
FreeBSD 4.0-CURRENT #4: Thu Jan 6 20:45:45 CET 2000
[EMAIL PROTECTED]:/usr/src/sys/compile/nullum
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium III/Xeon (451.02-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x672 Stepping = 2
Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,XMM>
real memory = 268423168 (262132K bytes)
config> #flags wdc0 0xa0ffa0ff
Invalid command or syntax. Type `?' for help.
config> #flags wdc1 0xa0ffa0ff
Invalid command or syntax. Type `?' for help.
config> #irq isic0 10
Invalid command or syntax. Type `?' for help.
config> #pnp 1 0 bios enable port0 0x220 irq0 5 drq0 1 drq1 3
Invalid command or syntax. Type `?' for help.
config> #pnp 1 0 bios enable port0 0xd80 irq0 11
Invalid command or syntax. Type `?' for help.
config> pnp 1 1 os enable irq0 5 drq0 1 port0 0x220
Invalid command or syntax. Type `?' for help.
config> #iosiz npx0 262144
Invalid command or syntax. Type `?' for help.
config> quit
avail memory = 256667648 (250652K bytes)
Programming 24 pins in IOAPIC #0
IOAPIC #0 intpin 2 -> irq 0
FreeBSD/SMP: Multiprocessor motherboard
cpu0 (BSP): apic id: 1, version: 0x00040011, at 0xfee00000
cpu1 (AP): apic id: 0, version: 0x00040011, at 0xfee00000
io0 (APIC): apic id: 2, version: 0x00170011, at 0xfec00000
Preloaded elf kernel "kernel.xxx" at 0xc036d000.
Preloaded userconfig_script "/boot/kernel.conf" at 0xc036d0ac.
Preloaded elf module "bktr.ko" at 0xc036d0fc.
VESA: v2.0, 8192k memory, flags:0x1, mode table:0xc02ff3c2 (1000022)
VESA: Matrox Graphics Inc.
Pentium Pro MTRR support enabled
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Intel 82443BX (440 BX) host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
pcib1: <Intel 82443BX (440 BX) PCI-PCI (AGP) bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
vga-pci0: <Matrox model 0521 graphics accelerator> irq 16 at device 0.0 on pci1
isab0: <Intel 82371AB PCI to ISA bridge> at device 4.0 on pci0
isa0: <ISA bus> on isab0
pci0: Intel PIIX4 ATA controller (vendor=0x8086, dev=0x7111) at 4.1
uhci0: <Intel 82371AB/EB (PIIX4) USB controller> irq 19 at device 4.2 on pci0
usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
intpm0: <Intel 82371AB Power management controller> at device 4.3 on pci0
intpm0: I/O mapped e800
intpm0: intr IRQ 9 enabled revision 0
smbus0: <System Management Bus> on intsmb0
smb0: <SMBus general purpose I/O> on smbus0
intpm0: PM I/O mapped e400
ahc0: <Adaptec aic7890/91 Ultra2 SCSI adapter> irq 19 at device 6.0 on pci0
ahc0: aic7890/91 Wide Channel A, SCSI Id=7, 16/255 SCBs
pci0: unknown card (vendor=0x10b7, dev=0x9055) at 9.0 irq 19
bktr0: <BrookTree 878> irq 18 at device 10.0 on pci0
bktr0: Hauppauge Model 61344 D121
bktr0: Detected a MSP3410D-B4 at 0x80
Hauppauge WinCast/TV, Philips FR1216 PAL FM tuner, msp3400c stereo, remote control.
pci0: unknown card (vendor=0x109e, dev=0x0878) at 10.1 irq 18
sym0: <895> irq 17 at device 11.0 on pci0
sym0: Symbios NVRAM, ID 7, Fast-40, LVD, parity checking
sym0: open drain IRQ line driver, using on-chip SRAM
isic0: <ELSA MicroLink ISDN/PCI> irq 16 at device 12.0 on pci0
isic0: Error, IPAC version 2 unknown!
device_probe_and_attach: isic0 attach returned 6
isa0: too many memory rangesfdc0: <NEC 72065B or clone> at port 0x3f0-0x3f7 irq 6 drq
2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <keyboard controller (i8042)> at port 0x60-0x6f on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
vga0: <Generic ISA VGA> at port 0x3b0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> on isa0
sc0: VGA <16 virtual consoles, flags=0x200>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
sio2: configured irq 19 not in bitmap of probed irqs 0
sio3: configured irq 19 not in bitmap of probed irqs 0
ppc0 at port 0x378-0x37f irq 7 flags 0x40 on isa0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/9 bytes threshold
lpt0: <generic printer> on ppbus 0
lpt0: Interrupt-driven port
ppi0: <generic parallel i/o> on ppbus 0
unknown0: <ESS ES1868 Plug and Play AudioDrive> at port 0x800-0x807 on isa0
sbc0: <ESS ES1868> at port 0x220-0x22f,0x388-0x38b,0x330-0x331 irq 5 drq 1,0 on isa0
pcm0: <SB DSP 3.01 (ESS mode)> on sbc0
unknown1: <ESS ES1868 Plug and Play AudioDrive> at port 0x201 on isa0
unknown2: <ESS ES1868 Plug and Play AudioDrive> at port 0x168-0x16f,0x36e-0x36f irq 12
on isa0
unknown: <PNP0401> can't assign resources
unknown: <PNP0501> can't assign resources
unknown: <PNP0501> can't assign resources
unknown: <PNP0700> can't assign resources
unknown3: <PNP0c01> at iomem
0-0x9ffff,0x100000-0xfffffff,0xe8000-0xeffff,0xf0000-0xf3fff,0xf4000-0xf7fff,0xf8000-0xfffff,0xd3800-0xd3fff,0xfec00000-0xfec00fff
on isa0
unknown: <PNP0000> can't assign resources
unknown4: <PNP0100> at port 0x40-0x43 irq 0 on isa0
unknown5: <PNP0b00> at port 0x70-0x71 irq 8 on isa0
unknown: <PNP0303> can't assign resources
unknown6: <PNP0c04> at port 0xf0 irq 13 on isa0
unknown7: <PNP0200> at port 0-0xf,0x80-0x90,0x94-0x9f,0xc0-0xde drq 4 on isa0
unknown: <PNP0800> can't assign resources
unknown8: <PNP0a03> at port 0xcf8-0xcff on isa0
unknown: <PNP0c02> can't assign resources
APIC_IO: Testing 8254 interrupt delivery
APIC_IO: routing 8254 via IOAPIC #0 intpin 2
i4btrc: 4 ISDN trace device(s) attached
i4brbch: 4 raw B channel access device(s) attached
i4btel: 2 ISDN telephony interface device(s) attached
i4bipr: 4 IP over raw HDLC ISDN device(s) attached
i4bctl: ISDN system control port attached
i4bisppp: 4 ISDN SyncPPP device(s) attached
i4b: ISDN call control device attached
IP packet filtering initialized, divert enabled, rule-based forwarding disabled,
logging limited to 100 packets/entry by default
Waiting 2 seconds for SCSI devices to settle
(noperiph:sym0:0:-1:-1): SCSI BUS reset delivered.
SMP: AP CPU #1 Launched!
Mounting root from ufs:/dev/da0s1a
da1 at sym0 bus 0 target 1 lun 0
da1: <IBM DDRS-39130D DC1B> Fixed Direct Access SCSI-2 device
da1: 80.000MB/s transfers (40.000MHz, offset 15, 16bit), Tagged Queueing Enabled
da1: 8715MB (17850000 512 byte sectors: 255H 63S/T 1111C)
da0 at ahc0 bus 0 target 0 lun 0
da0: <IBM DDRS-34560D DC1B> Fixed Direct Access SCSI-2 device
da0: 80.000MB/s transfers (40.000MHz, offset 15, 16bit), Tagged Queueing Enabled
da0: 4357MB (8925000 512 byte sectors: 255H 63S/T 555C)
da2 at sym0 bus 0 target 2 lun 0
da2: <IBM DDRS-39130D DC1B> Fixed Direct Access SCSI-2 device
da2: 80.000MB/s transfers (40.000MHz, offset 15, 16bit), Tagged Queueing Enabled
da2: 8715MB (17850000 512 byte sectors: 255H 63S/T 1111C)
da3 at sym0 bus 0 target 3 lun 0
da3: <IBM DDRS-39130D DC1B> Fixed Direct Access SCSI-2 device
da3: 80.000MB/s transfers (40.000MHz, offset 15, 16bit), Tagged Queueing Enabled
da3: 8715MB (17850000 512 byte sectors: 255H 63S/T 1111C)
da4 at sym0 bus 0 target 4 lun 0
da4: <IBM DDRS-39130D DC1B> Fixed Direct Access SCSI-2 device
da4: 80.000MB/s transfers (40.000MHz, offset 15, 16bit), Tagged Queueing Enabled
da4: 8715MB (17850000 512 byte sectors: 255H 63S/T 1111C)
cd0 at ahc0 bus 0 target 4 lun 0
cd0: <PLEXTOR CD-ROM PX-40TS 1.00> Removable CD-ROM SCSI-2 device
cd0: 20.000MB/s transfers (20.000MHz, offset 15)
cd0: cd present [327689 x 2048 byte records]
vinum: loaded
vinum: reading configuration from /dev/da4s1d
vinum: updating configuration from /dev/da1s1d
vinum: updating configuration from /dev/da2s1d
vinum: updating configuration from /dev/da3s1d
cd1 at ahc0 bus 0 target 6 lun 0
cd1: <YAMAHA CRW6416S 1.0c> Removable CD-ROM SCSI-2 device
cd1: 10.000MB/s transfers (10.000MHz, offset 15)
cd1: Attempt to query device size failed: NOT READY, Medium not present - tray closed
Current Parameters:
(pass6:sym0:0:4:0): sync parameter: 10
(pass6:sym0:0:4:0): frequencey: 40.000MHz
(pass6:sym0:0:4:0): offset: 15
(pass6:sym0:0:4:0): bus width: 16 bits
(pass6:sym0:0:4:0): disconnection is enabled
(pass6:sym0:0:4:0): tagged queueing is enabled
Current Parameters:
(pass3:sym0:0:1:0): sync parameter: 0
(pass3:sym0:0:1:0): offset: 0
(pass3:sym0:0:1:0): bus width: 8 bits
(pass3:sym0:0:1:0): disconnection is enabled
(pass3:sym0:0:1:0): tagged queueing is enabled
Current Parameters:
(pass3:ncr0:0:1:0): sync parameter: 12
(pass3:ncr0:0:1:0): frequencey: 20.000MHz
(pass3:ncr0:0:1:0): offset: 15
(pass3:ncr0:0:1:0): bus width: 16 bits
(pass3:ncr0:0:1:0): disconnection is enabled
(pass3:ncr0:0:1:0): tagged queueing is enabled
