Got myself a Toshiba Portégé 3110CT last week. The IDE controller
isn't recognized by the ata driver. It's an Intel(0x8086) with the
device ID 0x7199. Until the last DMA related checkins by Sřren, the drive
was working in PIO mode.
Now it says it's using DMA and after the "Mounting root from ..." message,
I get
ad0: ad_timeout: lost disk contact - resetting
ata0: resetting devices ..
and then it hangs with the disk activity led on.
Todays ata checkin said "Try to enable DMA on generic controllers ...",
but it still doesn't work. Now it also
says "ata0: master: success setting up WDMA2 mode on generic chip".
The wdc driver seems to work ok with the 0xa0ffa0ff flags.
I have tried looking around on developer.intel.com, but couldn't find
any reference to the device ID 0x7199. Where can I find which chipset
this is?
boot -v from last working PIO mode below
Copyright (c) 1992-1999 The FreeBSD Project.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
FreeBSD 4.0-CURRENT #1: Sun Dec 12 23:52:16 GMT 1999
root@h:/usr/src/sys/compile/H
Calibrating clock(s) ... TSC clock: 299933222 Hz, i8254 clock: 1193150 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz
CLK_USE_TSC_CALIBRATION not specified - using old calibration method
CPU: Pentium II/Celeron (299.94-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x66a Stepping = 10
Features=0x183f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR>
real memory = 134086656 (130944K bytes)
Physical memory chunk(s):
0x00001000 - 0x0009efff, 647168 bytes (158 pages)
0x0030d000 - 0x07fd7fff, 130854912 bytes (31947 pages)
avail memory = 126955520 (123980K bytes)
bios32: Found BIOS32 Service Directory header at 0xc00f0220
bios32: Entry = 0xfc455 (c00fc455) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0xedcd
pnpbios: Found PnP BIOS data at 0xc00f8ed0
pnpbios: Entry = f0000:9344 Rev = 1.0
pnpbios: Event flag at 510
pnpbios: OEM ID 1934f351
Other BIOS signatures found:
ACPI: 000f0170
Preloaded elf kernel "kernel" at 0xc02f4000.
Pentium Pro MTRR support enabled
md0: Malloc disk
Creating DISK md0
pci_open(1): mode 1 addr port (0x0cf8) is 0x00000000
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=71948086)
npx0: <math processor> on motherboard
npx0: INT 16 interface
pci_open(1): mode 1 addr port (0x0cf8) is 0x00000000
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=71948086)
pcib0: <Host to PCI bridge> on motherboard
found-> vendor=0x8086, dev=0x7194, revid=0x01
class=06-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
found-> vendor=0x1023, dev=0x9525, revid=0x49
class=03-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=11
map[10]: type 1, range 32, base ff400000, size 22
map[14]: type 1, range 32, base ff3e0000, size 17
map[18]: type 1, range 32, base fec00000, size 22
found-> vendor=0x8086, dev=0x7198, revid=0x01
class=06-80-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
found-> vendor=0x8086, dev=0x7199, revid=0x00
class=01-01-80, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
map[20]: type 1, range 32, base 0000fff0, size 4
found-> vendor=0x8086, dev=0x719a, revid=0x00
class=0c-03-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=d, irq=11
map[20]: type 1, range 32, base 0000ff80, size 5
found-> vendor=0x8086, dev=0x719b, revid=0x00
class=06-80-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
found-> vendor=0x1179, dev=0x0d01, revid=0x00
class=0d-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=11
map[10]: type 1, range 32, base 0000ff60, size 5
found-> vendor=0x1179, dev=0x0617, revid=0x20
class=06-07-00, hdrtype=0x02, mfdev=1
subordinatebus=14 secondarybus=14
intpin=a, irq=255
found-> vendor=0x125d, dev=0x1978, revid=0x10
class=04-01-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=11
map[10]: type 1, range 32, base 0000fc00, size 8
found-> vendor=0x11c1, dev=0x0441, revid=0x01
class=07-80-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=3
map[10]: type 1, range 32, base ffefff00, size 8
map[14]: type 3, range 32, base 000002f8, size 3
map[18]: type 1, range 32, base 00001c00, size 8
found-> vendor=0x8086, dev=0x1229, revid=0x08
class=02-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=11
map[10]: type 1, range 32, base febff000, size 12
map[14]: type 1, range 32, base 0000fb40, size 6
map[18]: type 1, range 32, base fea00000, size 20
pci0: <PCI bus> on pcib0
vga-pci0: <Trident model 9525 VGA-compatible display device> irq 11 at device 4.0 on
pci0
chip1: <PCI to Other bridge (vendor=8086 device=7198)> at device 7.0 on pci0
ata-pci0: <Unknown PCI ATA controller (generic mode)> at device 7.1 on pci0
ata-pci0: Busmastering DMA supported
ata0: iobase=0x01f0 altiobase=0x03f6
ata0: mask=03 status0=50 status1=00
ata0: mask=03 status0=50 status1=00
ata0: devices = 0x1
ata0 at 0x01f0 irq 14 on ata-pci0
ata1: iobase=0x0170 altiobase=0x0376
ata1: mask=00 status0=ff status1=ff
uhci0: <UHCI (generic) USB controller> irq 11 at device 7.2 on pci0
uhci0: (New UHCI DeviceId=0x719a8086)
usb0: <UHCI (generic) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: (0x719a8086) UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
chip2: <PCI to Other bridge (vendor=8086 device=719b)> at device 7.3 on pci0
pci0: unknown card (vendor=0x1179, dev=0x0d01) at 9.0 irq 11
chip3: <PCI to CardBus bridge (vendor=1179 device=0617)> at device 11.0 on pci0
pci0: unknown card (vendor=0x125d, dev=0x1978) at 12.0 irq 11
pci0: unknown card (vendor=0x11c1, dev=0x0441) at 13.0 irq 3
fxp0: <Intel EtherExpress Pro 10/100B Ethernet> irq 11 at device 14.0 on pci0
using shared irq11.
fxp0: Ethernet address 00:00:39:21:b0:1a
bpf: fxp0 attached
eisa0: <EISA bus> on motherboard
eisa0: unknown card @@@0000 (0x00000000) at slot 1
isa0: <ISA bus> on motherboard
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
fdc0: <NEC 765 or clone> at port 0x3f0-0x3f7 irq 6 drq 2 on isa0
ata-isa0: already registered as ata0
ata1: iobase=0x0170 altiobase=0x0376
ata1: mask=00 status0=ff status1=ff
atkbdc0: <keyboard controller (i8042)> at port 0x60-0x6f on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0047
atkbd: keyboard ID 0x41ab (2)
kbdc: RESET_KBD return code:00fa
kbdc: RESET_KBD status:00aa
kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000
psm0: current command byte:0047
kbdc: TEST_AUX_PORT status:0000
kbdc: RESET_AUX return code:00fa
kbdc: RESET_AUX status:00aa
kbdc: RESET_AUX ID:0000
psm: status 00 02 64
psm: status 00 00 64
psm: status 00 03 64
psm: status 00 03 64
psm: status 10 00 64
psm: data 08 00 00
psm: status 00 02 64
psm: data 08 00 00
psm: status 00 02 64
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0-00, 2 buttons
psm0: config:00000000, flags:00000000, packet size:3
psm0: syncmask:c0, syncbits:00
vga0: <Generic ISA VGA> at port 0x3b0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3b0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 07 80 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
EGA/VGA parameters to be used for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
sc0: <System console> on isa0
sc0: VGA <16 virtual consoles, flags=0x200>
sc0: fb0 kbd0
pcic: polling, can't alloc 0
pcic0: <Intel i82365> on isa0
pccard0: <PC Card bus -- kludge version> on pcic0
sio0: irq maps: 0x41 0x51 0x51 0x51
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: irq maps: 0x41 0x41 0x41 0x41
sio1: probe failed test(s): 0 1 2 4
ppc: parallel port found at 0x378
ppc: chipset forced to generic
ppc0: ECP SPP SPP
ppc0 at port 0x378-0x37f irq 7 flags 0x40 on isa0
ppc0: Generic chipset (ECP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
plip: irq 7
plip0: <PLIP network interface> on ppbus 0
bpf: lp0 attached
lpt0: <generic printer> on ppbus 0
lpt0: Interrupt-driven port
ppi0: <generic parallel i/o> on ppbus 0
isa_probe_children: probing PnP devices
BIOS Geometries:
0:0313fe3f 0..787=788 cylinders, 0..254=255 heads, 1..63=63 sectors
0 accounted for
Device configuration finished.
bpf: sl0 attached
bpf: ppp0 attached
new masks: bio 40084840, tty 40031092, net 40071892
bpf: lo0 attached
ad0: piomode=4 dmamode=2 udmamode=2 cblid=0
ad0: <TOSHIBA MK6411MAT/J0.07 H> ATA-4 disk at ata0 as master
ad0: 6194MB (12685680 sectors), 13424 cyls, 15 heads, 63 S/T, 512 B/S
ad0: 16 secs/int, 1 depth queue, PIO
Creating DISK ad0
Creating DISK wd0
Mounting root from ufs:/dev/ad0s2a
ad0s1: type 0x6, start 63, end = 2056319, size 2056257 : OK
ad0s2: type 0xa5, start 2056320, end = 7293509, size 5237190 : OK
start_init: trying /sbin/init
--
Mikael Hybsch Email: [EMAIL PROTECTED]
RSA Security AB Phone: +46-8-7250900
Box 10704 Fax: +46-8-6494970
S-121 29 STOCKHOLM, SWEDEN
To Unsubscribe: send mail to [EMAIL PROTECTED]
with "unsubscribe freebsd-current" in the body of the message
