I have a pnp modem "SupraExpress 56i Sp V.90" that works fine with a
kernel from Aug 22. Here is an excerpt from a successful boot:
atkbdc0: <keyboard controller (i8042)> at port 0x60-0x6f on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
vga0: <Generic ISA VGA> at port 0x3b0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> on isa0
sc0: VGA <16 virtual consoles, flags=0x200>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
---> sio2 at port 0x3e8-0x3ef irq 11 on isa0
---> sio2: type 16550A
Waiting 5 seconds for SCSI devices to settle
sa0 at ahc0 bus 0 target 3 lun 0
sa0: <HP C1533A 9406> Removable Sequential Access SCSI-2 device
sa0: 10.000MB/s transfers (10.000MHz, offset 8)
changing root device to da0s3a
[...]
Todays GENERIC kernel hangs after correctly detecting sio2, with no keyboard
input, reboot necessary, yada yada yada.
Disabling sio2 from the config menu will let it boot. Here's a
verbose log of todays GENERIC kernel with sio2 disabled:
us: fast PIO disabled
intel_piix_status: secondary master/slave sample = 5, master/slave recovery = 4
intel_piix_status: secondary slave fastDMAonly disabled, pre/post disabled,
intel_piix_status: IORDY sampling disabled,
intel_piix_status: fast PIO disabled
ide_pci: busmaster 1 status: 04 from port: 0000d80a
chip1: <UHCI USB controller> irq 9 at device 4.2 on pci0
chip2: <Intel 82371AB Power management controller> at device 4.3 on pci0
ahc0: <Adaptec aic7880 Ultra SCSI adapter> irq 9 at device 6.0 on pci0
ahc0: Reading SEEPROM...done.
ahc0: internal 50 cable is present, internal 68 cable is present
ahc0: external cable is present
ahc0: BIOS eeprom not present
ahc0: aic7880 Wide Channel A, SCSI Id=7, 16/255 SCBs
ahc0: Downloading Sequencer Program... 411 instructions downloaded
fxp0: <Intel EtherExpress Pro 10/100B Ethernet> irq 12 at device 10.0 on pci0
fxp0: Ethernet address 00:a0:c9:b2:18:ef
bpf: fxp0 attached
vga-pci0: <ATI Mach64-GX graphics accelerator> at device 11.0 on pci0
ahc1: <Adaptec 2940 Ultra SCSI adapter> irq 10 at device 12.0 on pci0
ahc1: Reading SEEPROM...done.
ahc1: internal 50 cable not present, internal 68 cable not present
ahc1: external cable is present
ahc1: BIOS eeprom is present
ahc1: High byte termination Enabled
ahc1: Low byte termination Enabled
ahc1: aic7880 Wide Channel A, SCSI Id=7, 16/255 SCBs
ahc1: Downloading Sequencer Program... 411 instructions downloaded
fe0: not probed (disabled)
fdc0: not probed (disabled)
wdc0: not probed (disabled)
wdc1: not probed (disabled)
adv0: not probed (disabled)
bt0: not probed (disabled)
aha0: not probed (disabled)
wt0: not probed (disabled)
mcd0: not probed (disabled)
matcd0: not probed (disabled)
scd0: not probed (disabled)
atkbdc0: <keyboard controller (i8042)> at port 0x60-0x6f on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0067
atkbd: keyboard ID 0x41ab (2)
kbdc: RESET_KBD return code:00fa
kbdc: RESET_KBD status:00aa
kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000
psm0: current command byte:0067
kbdc: TEST_AUX_PORT status:0000
kbdc: RESET_AUX return code:00fe
kbdc: DIAGNOSE status:0055
kbdc: TEST_KBD_PORT status:0000
psm0: failed to reset the aux device.
vga0: <Generic ISA VGA> at port 0x3b0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3b0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0e 0f 00 00 07 80 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
EGA/VGA parameters to be used for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
sc0: <System console> on isa0
sc0: VGA <16 virtual consoles, flags=0x200>
sc0: fb0 kbd0
sio0: irq maps: 0x1 0x11 0x1 0x1
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1: irq maps: 0x1 0x9 0x1 0x1
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
sio2: not probed (disabled)
sio3: not probed (disabled)
ppc0: not probed (disabled)
ed0: not probed (disabled)
ie0: not probed (disabled)
ep0: not probed (disabled)
ex0: not probed (disabled)
le0: not probed (disabled)
lnc0: not probed (disabled)
cs0: not probed (disabled)
----> It hangs here if sio2 is enabled
unknown0: <SupraExpress 56i Sp V.90> at port 0x3e8-0x3ef irq 5 on isa0
^^^^^ really at irq 11
BIOS Geometries:
0:0106fe3f 0..262=263 cylinders, 0..254=255 heads, 1..63=63 sectors
1:03fefe3f 0..1022=1023 cylinders, 0..254=255 heads, 1..63=63 sectors
0 accounted for
Device configuration finished.
Any ideas? BTW, here's a pnpinfo -v:
Checking for Plug-n-Play devices...
Card assigned CSN #1
Vendor ID SUP2480 (0x8024b04e), Serial Number 0x00001334
PnP Version 1.0, Vendor Version 0
Device Description: SupraExpress 56i Sp V.90
Logical Device ID: SUP2480 0x8024b04e #0
Device supports I/O Range Check
Compatible Device ID: SUP2080 (8020b04e)
TAG Start DF
I/O Range 0x3f8 .. 0x3f8, alignment 0x8, len 0x8
[16-bit addr]
IRQ: 4 - only one type (true/edge)
TAG Start DF
I/O Range 0x2f8 .. 0x2f8, alignment 0x8, len 0x8
[16-bit addr]
IRQ: 3 - only one type (true/edge)
TAG Start DF
I/O Range 0x3e8 .. 0x3e8, alignment 0x8, len 0x8
[16-bit addr]
IRQ: 4 - only one type (true/edge)
TAG Start DF
I/O Range 0x2e8 .. 0x2e8, alignment 0x8, len 0x8
[16-bit addr]
IRQ: 3 - only one type (true/edge)
TAG Start DF
I/O Range 0x3e8 .. 0x3e8, alignment 0x8, len 0x8
[16-bit addr]
IRQ: 5 - only one type (true/edge)
TAG Start DF
I/O Range 0x2e8 .. 0x2e8, alignment 0x8, len 0x8
[16-bit addr]
IRQ: 5 - only one type (true/edge)
TAG Start DF
I/O Range 0x3e8 .. 0x3e8, alignment 0x8, len 0x8
[16-bit addr]
IRQ: 3 4 5 7 10 11 12 15 - only one type (true/edge)
TAG Start DF
I/O Range 0x2e8 .. 0x2e8, alignment 0x8, len 0x8
[16-bit addr]
IRQ: 3 4 5 7 10 11 12 15 - only one type (true/edge)
TAG Start DF
I/O Range 0x3f8 .. 0x3f8, alignment 0x8, len 0x8
[16-bit addr]
IRQ: 3 4 5 7 10 11 12 15 - only one type (true/edge)
TAG Start DF
I/O Range 0x2f8 .. 0x2f8, alignment 0x8, len 0x8
[16-bit addr]
IRQ: 3 4 5 7 10 11 12 15 - only one type (true/edge)
TAG Start DF
I/O Range 0x200 .. 0x3f8, alignment 0x8, len 0x8
[16-bit addr]
IRQ: 3 4 5 7 10 11 12 15 - only one type (true/edge)
TAG End DF
End Tag
Successfully got 38 resources, 1 logical fdevs
-- card select # 0x0001
CSN SUP2480 (0x8024b04e), Serial Number 0x00001334
Logical device #0
IO: 0x03e8 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
IRQ 11 0
DMA 4 0
IO range check 0x00 activate 0x01
Dan Eischen
[EMAIL PROTECTED]
To Unsubscribe: send mail to [EMAIL PROTECTED]
with "unsubscribe freebsd-current" in the body of the message
